Carter Desk White

Introduction

Thank you for purchasing the Carter Desk. Please read the instructions and warnings carefully before use, to ensure safe and satisfactory operation of this product.

At John Lewis, we are committed to making great products possible. From our in-house Design Team, to our Buyers, we work together to bring great designs to life. Our expert Product Technologists work collaboratively with our buyers and suppliers to assure the legality, safety and quality of the product we sell. We are all committed to designing and developing products to the highest industry standards. We hope you are happy with your product and welcome any feedback or comments you may have.

The John Lewis Team

Assembly Information

Tools required: [Allen key symbol]

Time to assemble: 1 hour

People to assemble: 2 [Two people symbol]

Important Safety Information

Warnings

• The product should only be used on firm, level ground.
• Keep small parts out of reach of children.
• Ensure the product is fully assembled as illustrated before use.

Do's

• Check the pack and make sure you have all the parts listed.
• Check all screws or bolts are tightened and inspect regularly.
• Make sure the legs remain in contact with the ground at all times.

Don'ts

• ❌ Do not over tighten screws or bolts.
• ❌ Do not stand on the product.
• ❌ Do not use power tools to construct as overtightening and panel failure may occur.

Visual Checks:

• [Checklist symbol] Check the pack and ensure all parts are present.
• [Box with checklist symbol] Verify contents against the parts list.
• [Phone symbol] Contact John Lewis customer service at 03456 049 049 for assistance.
• ❌ Do not assemble directly on the floor.
• [Two people symbol] Assembly requires two people.
• ❌ Do not place the desk upside down directly on the floor.
• [Rug symbol] Assemble on a soft surface like a rug to avoid scratches.

Product Components

Your desk

Fixtures and Fittings

Fixtures and fittings supplied (actual size)

[Ruler symbol] Measurement scale for fittings.

Fixtures and fittings supplied (not actual size)

Assembly Instructions

Step 1

Parts: 1

Action: Please remove the two compartment lids prior to assembly.

[Diagram description: The desk top is shown with two circular compartment lids. Arrows indicate the lids should be removed.]

Step 2

Parts: 2

Action: Gently place the desk top upside down on a soft surface to avoid scratches. Then place the leg frames as shown.

[Diagram description: The desk top is shown upside down. Two leg frames are positioned to be attached to the underside of the desk top. Arrows indicate the placement of the leg frames.]

Step 3

Fittings and tools: A, B, C, D

Action: Insert bolts A with spring washers C and washers B into the allocated holes in the leg frames. Do not fully tighten at this stage.

[Diagram description: A close-up view shows how to attach a leg frame to the desk top. Assembly bolts (A) are shown with spring washers (C) and washers (B) being inserted into pre-drilled holes. An Allen key (D) is also shown. Arrows indicate the direction of insertion.]

Step 4

Fittings and tools: A, B, C, D

Action: Now insert the remaining bolts A with spring washers C and washers B as shown, and tighten firmly when all bolts are inserted. Now also fully tighten all bolts inserted at step 3.

[Diagram description: The desk is shown with all leg frames attached. More bolts (A), washers (B), and spring washers (C) are being inserted and tightened using the Allen key (D). Arrows indicate tightening.]

Step 5 - Cable Management

[Diagram description: The desk top is shown. Circular compartment lids are being placed into their respective openings. Arrows indicate the direction of placement and rotation.]

Step 6

[Diagram description: The desk top is shown with the compartment lids in place. Arrows indicate pushing down on the lids to secure them.]

Care Guide

Care and Maintenance

Wood Furniture

Wood displays different grain patterns depending on which way they cut - for example, the 'medullary ray' which can appear on oak furniture is a mark of good quality timber - these are just characteristics of the natural beauty of the wood. Some furniture is also deliberately aged and rustic.

Wood veneers also allow distinctive patterns to be created on flat surfaces, such as table tops and drawer fronts by the way the slivers are arranged.

All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade from items that have been previously purchased.

How to care for your wood furniture

Furniture with a painted surface or hard lacquer should be dusted with a dry cloth.

Spray polishes are best avoided as they contain silicones which may spoil the furniture's surface by building up over time.

Make sure all surfaces are protected from heat and liquids by mats and coasters. Wipe up spills immediately and ensure that a mat or pad is placed under paper if you are writing.

Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next to heat sources such as radiators or fires. Be particularly careful with solid wood as the lack of humidity caused by central heating can cause damage such as warping.

Protect surfaces from scratches and marks by using mats and coasters.

Safety Instructions

• Never drag furniture when moving it, always lift it.
• Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
• Please take care when handling or moving the furniture as careless handling may cause damage or injury.
• Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person. No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.

Retain these instructions for future reference.