mailto:info@accur8tech.com
User Manual for Weather models including: ACCUR8 CO2 Monitor with Temperature and Humidity, ACCUR8 CO2, Monitor with Temperature and Humidity, Temperature and Humidity
prieš 2 dienas — User Manual. ACCUR8 CO2-5000. CO2 Monitor with Temperature & Humidity. 1. Introduction. Thank you for purchasing this ACCUR8 product. This user manual is to ...
User Manual. ACCUR8 CO2-5000. CO2 Monitor with Temperature & Humidity. 1. Introduction. Thank you for purchasing this ACCUR8 product. This user manual is to ...
User Manual. ACCUR8 CO2-5000. CO2 Monitor with Temperature & Humidity. 1. Introduction. Thank you for purchasing this ACCUR8 product. This user manual is to ...
File Info : application/pdf, 12 Pages, 602.73KB
DocumentDocumentUser Manual ACCUR8 CO2-5000 CO2 Monitor with Temperature & Humidity 1. Introduction Thank you for purchasing this ACCUR8 product. This user manual is to be considered a component of the device. Read carefully before using the device. Keep in a safe place for future reference. When the device is sold or given to someone else, the user manual must be provided to the new owner/user of the product. As part of our ongoing policy to improve the design and specification of our products, we reserve the right to change any detail given without prior notice. Tempcon Instrumentation Ltd shall not be responsible for any liability of any nature which may result from the use of any information provided in technical literature. Errors and technical changes excepted. © 2022 Tempcon Instrumentation Ltd. All rights reserved. 2. General Safety Instructions Risk of electric shock Only use the device as described in the manual; otherwise, you run the risk of an electric shock. · Children must only use the device under adult supervision. · Disconnect the device from the power supply before starting any cleaning of the device. · Position your device so that it can be disconnected from the power supply at any time. The power socket should be installed near the device and should be easily accessible as the mains cable plug is used to disconnect the device from the power supply. · To disconnect the device from the power supply, always pull on the plug. Never pull on the cable. · Before starting up the device, check the device, the cables and the connections for signs of damage. · Never use a damaged device or a device with damaged parts. · Only use the display console in a dry environment and do not touch it with wet or moist parts of your body. Risk of suffocation/choking Improper use of this product can result in suffocation, especially for children. The following safety information must be observed at all times. · Keep packaging materials away from children. They can cause suffocation. · This product contains small parts that could be swallowed by children. There is a risk of choking. Risk of fire/explosion Improper use of this product can cause an explosion. The following safety information must be observed at all times to prevent an explosion. · Do not expose the device to high temperatures. Excessive heat or improper handling could trigger a short circuit, a fire, or an explosion. Risk of damage to property Improper handling can result in damage to the device and/or to the accessories. Always observe the following safety information when using the device: 1 · Never disassemble the device. In the event of a fault, please contact your retailer. · Do not expose this device to high temperatures and protect it from water and high humidity. · Protect the device from severe shocks or excessive vibrations. · For this device, only use accessories and spare parts that comply with the technical information. Risk of voltage damage The manufacturer is not liable for voltage damage through the use of an improper power adaptor. 3. Packing List CO2 Monitor Unit USB cable for Power (standard USB power adaptor plug required) User Manual 4. Features at a Glance Large Display Touch Button Operation 15° Bevel Design, Easy to Read Low Drift NDIR Sensor, Long Lifespan Audible Alarm Chart with Variable Time Zoom Levels CO2/ Humidity /Temperature Sensors Auto-Calibration and Manual Calibration Max/Min Values Displayed on Screen 2 5. Overview 6. General Operation and Settings 1. Use the provided USB cable to connect the device. Once the countdown is complete, your device is ready to use. 2. Use the Up and Down buttons to switch timeline and CO2/HUMIDITY/TEMP. The trend chart displays the history records for any of the three parameters. See details on Page 4. 3. To restore factory defaults, hold the Enter button for 3 seconds until an audible beep is heard. 4. Pressing the Menu button once will bring up the main menu. To select the function, press Menu/Down button. See details on Page 5. 5. Select `Plant' to switch between human and plant modes. See detail on Page 5. 6. Select `ADV' to change the high/low alarms for human and plant modes. See details on Page 6. 7. Enter ALARM to switch between alarm and mute. See details on Page 6. 8. Enter °C/°F to select temperature units °C or °F. See details on Page 7. 7. Operating Instructions 1. When first unboxing, plug in the unit with the provided USB cable. 2. Once successfully connected, the power indicator and three LEDs flash one by one. 3. The main display shows a countdown from 10. Once the countdown is complete, your product is ready to use. No initial setup or calibration is needed. 3 8. LCD Display 4 9. Trend Chart Display The chart below displays the past readings for any of the three parameters (CO2/Humidity/Temperature). There are four modes that can be toggled by using the Up button: CO2, Temp, Humidity, and Cycle (automatically cycles through CO2/Temp/ Humidity). The table below shows the available Zoom Levels for all parameters CO2/ Humidity/ Temp.as well as the duration of each division for corresponding Zoom Levels: 10. Max/Min At the top right corner of the display, there are two indicators: MAX and MIN. As the Zoom Level is changed, the MAX and MIN values will reflect the maximum and minimum values on the chart of the selected parameter (C02, Humidity and Temp). 5 11. Main Menu Functions The Main Menu functions can be activated by pressing the Menu button. Pressing Down/Menu once will bring up the main menu, with an underlining flashing bar indicating the current choice. To select the function, press Enter when it is underlined by the flashing bar. Note that after one minute if nothing is pressed, the Main Menu will disappear, and the device will revert to the normal state. 6 7 8 12. Specifications Typical test conditions: Ambient Temp: 23 ± 3°C, humidity=50%-70%, Altitude= 0-10 metres Operating Temperature Storage Temperature Operating & storage humidity 32°F - 122°F (0°C - 50°C) -4°F - 140°F (-20°C - 60°C) 0-95% (non-condensing) CO2 Measurement Measuring range Display resolution Accuracy Repeatability Temp compensation Response time Warm-up time (0-5000)ppm 1ppm (0-1000); 5ppm (1000-2000); 10ppm (>2000) (0-3000)ppm: ± 50ppm ± 5% of reading. (>3000)ppm: ± 7% of reading 20ppm at 400ppm ±0.1% of reading per °C <2 min for 63% of step change or< 4.6 min for 90% step change <20 seconds Temperature Measurement Operating temperature Display resolution Response time 32°F - 195°F (0°C ~90°C) 0.1°F (0.1°C) <20 minutes (63%) Humidity Measurement Measuring range Accuracy Display resolution 5-95% ±5% 1% Main interface display, 0.1% Max/Min display Operating Voltage Dimension Weight DC(5±0.25)V 120*90*35mm 170g device only 9 13. Appendix No. Refers Low/High Alarm 0, FOR Human 800-1200ppm 1, FOR Customised Plant 600-900ppm 2, FOR Bean 600-900ppm 3, FOR Chillies 800-1000ppm 4, FOR Cucumber 1000-1500ppm 5, FOR Grape 800-1400ppm 6, FOR Orchid 800-1400ppm 7, FOR Potato 1200-1800ppm 8, FOR Strawberry 800-1200ppm 9, FOR Tomato 800-1200ppm Adjustable Yes Yes No No No No No No No No 14. Service Please contact us for any questions regarding the product or claims, preferably by email. ACCUR8 Ford Lane Business Park Ford West Sussex BN18 0UZ UK Email: info@accur8tech.com Phone: +44 (0)1243 558 280 ACCUR8 is a registered trademark of Tempcon Instrumentation Ltd 15. EC Declaration of Conformity Tempcon Instrumentation Ltd has issued a declaration of conformity in accordance with applicable guidelines and corresponding standards. The full text of the EC declaration of conformity is available on request from the address above. 16. Disposal Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal. Do not dispose of electronic devices in the household rubbish! Used electronic devices must be collected separately and recycled in an environmentally friendly manner. Do not dispose of batteries and rechargeable batteries with the household waste. After they are used, the batteries can be returned to our point of sale or to a nearby location (for example, retailers or municipal collecting points). Batteries and rechargeable batteries are marked with a symbol of a crossed-out dustbin and the chemical symbol of the pollutant. "Cd" stands for Cadmium, "Hg" stands for mercury and "Pb" stands for lead. Document Version 1.1 10 This page has been intentionally left blank. 11 This page has been intentionally left blank. 12