Vivid Kiosk Assembly
The Vivid Kiosk assembly involves several steps, starting with identifying the packages.
- Identify a big package and a small package.
- Open the small package.
- Assemble the Lucid Storage Lightbox components.
- Install Part A according to the labels. Part A is now finished.
- Install Part B according to the labels. Part B is now finished.
- Install the top table.
- The final assembly shows the completed Vivid Kiosk with a graphic panel.
Fingerprint Cabinet Lock Features
- Biometric sensor: High sensitivity and rapid response.
- Capacity: Supports up to 20 fingerprints for multiple users.
- E-Key: Provides an emergency key and management function.
- Design: Zinc alloy panel with an elegant appearance.
- Mounting: Surface-mounted, suitable for drawers, cabinets, and wardrobes.
Fingerprint Cabinet Lock Operation
Automatic Mode
1. Adding New Fingerprints
To add a new fingerprint:
- Place a registered finger on the sensor. The green light will illuminate, and the latch will retract. Keep holding the finger until the green light stays on, then remove it.
- A blue light will appear. Place a finger on the sensor and remove it when the green light shows.
- Repeat the process of placing the finger on the sensor and removing it when the green light appears until a long green light is displayed for 2 seconds. This indicates the fingerprint is registered.
- A blue light will appear, indicating you can add more fingerprints.
Note:
- Ensure fingerprints are added before use. In factory settings, any finger can unlock the device.
- To ensure optimal performance, add at least 3 fingerprints.
2. Deleting Fingerprints
- Place any registered finger on the sensor. The green light will illuminate. Keep holding the finger until the green light illuminates again, then continue holding until the green light flashes red, and then remove the finger.
- A green light for 2 seconds indicates all fingerprints have been deleted.
3. Locking the Cabinet
Push the door closed. The lock will engage automatically.
4. Unlocking the Cabinet
- Place any registered fingerprint on the sensor.
- The green light will illuminate, indicating the cabinet is unlocked.
- Pull the door open.
Other Functions
E-Key Usage
- Insert the E-Key.
- Place any registered finger on the sensor. The green light will illuminate, and the cabinet will unlock.
- Pull the door open.
Low Battery Warning
When the battery is low, placing a registered fingerprint will cause the green light to flash once, followed by three red flashes, and then a long green light, indicating it is unlocked. Change the batteries immediately after opening the door.
Note: Use 3x AAA alkaline batteries. Do not use carbon batteries.
Outer Power Supply
In case of a low battery, you can connect a power bank or mobile plug for an external power supply. After unlocking, change the batteries immediately.
Fingerprint Cabinet Lock Installation Instructions
- Place the installation drawing on the door. Position it approximately 35mm from the door frame to the center hole (refer to Picture 1). Drill the hole accordingly.
- Connect one end of the panel connection line through the middle round hole to the lock box. Initially, use two M4*22 cross pan head screws to fix the panel to the door. Ensure the connection line is organized to prevent it from being pinched. Then, use two 3.5*30 cross countersunk head wood screws and one 3.5*16 cross countersunk head wood screw to secure the lock box to the door panel.
- Fix the striking plate using an ST3.5*12 screw. Ensure the latch functions correctly.
Screw Guide for Door Thickness:
| Door Thickness (mm) | Screw Type |
|---|---|
| 14mm~16mm | (M4*20) X 2 |
| 16mm~18mm | (M4*22) X 2 |
| 19mm~21mm | (M4*25) X 2 |
Components:
- Front Panel
- Lock Body
- Lock Body Cover
- Striking Plate
- Screws (M4*20, M4*22, M4*25, ST3.5*12)
- Wire
- Indicator (USB port)
- E-key