PA Speakers and Subwoofers in Good Quality - PRORECK
proreck.com
User Manual for PRORECK models including: SP-218X Active Powered PA DJ Subwoofer, SP-218X, Active Powered PA DJ Subwoofer, Powered PA DJ Subwoofer, PA DJ Subwoofer, DJ Subwoofer, Subwoofer
Proreck PR212T 6000W Active Subwoofer System
File Info : application/pdf, 4 Pages, 117.77KB
DocumentDocumentwwPbwRr.OaanuRddEPsw@iCoaRwKlppOewrrAsRoo-.UprrE1eerDC@occKIkkrOpe..Accr,cIoooUNkrmm.DeCccoIOkm.,cINomC Specifications Type Peak Power Power Output Voltage Input Inputs Outputs Electronic Crossover XLR High Pass Output Impedance Voice Coil Diameter Voice Coil Material Subwoofer SP-218X Sound reinforcement equipment for low frequency, with 5000W peak 1000W 115V~60Hz XLR INPUT XLR OUTPUT Electronic crossover (35-120 Hz) XLR high pass output (120Hz-20KHz) 4 Ohms 3" Kapton and Copper Dual 18 inch Proper use of the amplifier Your device has a built-in audio amplifier. To make the best use of it and to prolong its life, we recommend that you follow these instructions. -Do not exceed 80% of the volume control knobs. -Never use the unit for more than 4 hours at a time with high volume. -Never use a microphone near the device, this may cause your device to make a hissing sound. -Do not obstruct or block the rear panel ventilation, which has the heat sink that cools the amplifier. In order to get the best performance from your product, please read this instruction manual carefully before use and keep it for future reference. Customer Service Any questions, please feel free to contact us. Sales-1@proreck.com Warnings Keep the unit out of the reach of children. Do not touch the plug with wet hands and remove the cover or modify the unit, as you may receive an electric shock. Operation 1.Before power on, please reduce the volume to the minimum. 2.Install the equipment correctly. 3.Connect to the power supply. Precautions -Do not overload the device to avoid damage to the speakers. -Do not place heavy objects, including the equipment itself on top of the power cord. A damaged power cord poses serious hazards; especially avoid placing heavy objects on a power cord covered by a carpet. -Do not place an open fire on or next to the device. -For indoor use only. If the device is used outdoors, you must ensure that no moisture enters it. -Unplug the device from the power outlet when not in use. -Unplug the device from the power source before checking or replacing the fuse. -Make sure the device is placed on a stable and sturdy surface. -Use only suitable means of transport if you want to move the box. Always unplug the unit during a lightning storm or when it's not in use. -If the unit has not been used for a long time, condensation may form inside the case. Please allow the unit to reach room temperature before use. - Never try to repair the unit yourself, it does not contain any user-serviceable parts. 4 1 56 3 1 2 7 4 1 2 7 8 9 2 AMPLIFIER 1 XLR Output (FULL RANAGE) Parallel balanced stereo XLR output. It delivers an exact copy of the input signal. 2 XLR Input Balanced XLR input for connecting signals from mixers or other amplifiers. 3 Volume This knob allows to increase or decrease the volume control level. 4 Phase Phase selection button NORMAL- REV180°. 5 Limit This LED indicates that the input signal is too high, which may distort the output sound or even damage the unit. 6 Power Indicator Led power indicator. 7 XLR Output (HIGH PASS) Filtered balanced XLR output (high-pass from 120Hz). 8 ON/OFF Switch Turn on and turn off your unit with this interrupter. 9 Input Voltage 115V~60Hz Connect to Mixer with XLR Cable Mixer 3