User Guide for ZIGBEE models including: 80x60 Outdoor Siren with Solar, 80x60, Outdoor Siren with Solar, Siren with Solar, Solar
17 hours ago — Power: 5V/1A Type-C USB Powered. Battery type: 18650 rechargeable batter. Wireless protocol: Zigbee 3.0. Zigbee standard: Zigbee IEEE 802.15.4.
NEO NAS-AB06B Kültéri ZigBee Riasztósziréna TUYA
Outdoor Siren with Solar
USER GUIDE
ZIGBEE
Specifications
Power: 5V/1A Type-C USB Powered Battery type: 18650 rechargeable batter Wireless protocol: Zigbee 3.0 Zigbee standard: Zigbee IEEE 802.15.4 Wireless range: 45m(Max) Standby current: 2.5mA Type of alarm ringtone: 3 Maximum alarm sound:1M-100dB Waterproof rate: IPX5 Working temperature: -10¥j60¥c14j140 Working humidity: 1% j 95%RH(Non condensation) Size: 200mm x 150mm x 65.87mm Solar panel size: 132mm X 62mm Minimum light value for charging: 10000Lux
05
Product Configuration
Solar Panel
Backplate
Racks Indicator light (blue)
Buzzer Tamper alarm
Battery-bay 18650 Battery
Hanging hole
Remove the battery
compartment
Reset Button 01
Type-C USB charge port
LED State
Device Status
LED State
Configure network mode Indicator light flashes 2 times in 1s
Indicator light color
Blue
Reset
Long press the rest bottom for 6s
Installation Method
(1) Open the battery compartment and take out the insulating sheet at the battery end (2) Charge through the Type-C port and activate the device (3) Follow the instructions to connect the device to the network and connect to the APP (4) Cover the battery compartment, and use the accessory screwdriver to screw on the screws (5) Use accessory screws to fix the back plate at the installation position (6) Align the hanging hole of the Outdoor siren with the back plate and hang it (7)Note: When installing, please align the solar panel with the position where the sun shines for the longest time. If there is no sun for two consecutive months, remove the device and charge it through USB.
1. Backplate installation
Mark the position of the backplate holes on the wall and drilled
Align the backplate holes with the wall holes and fix with screws
Finish
Type-C power-on activation
Remove the battery cover
Remove the insulation sheet
Power on and activate the device, then add to the APP
02
Close the battery cover and screw it
2. Device installation 03
Align the racks on the backplate with the device mounting holes then fix it
Finish
3.Type-C USB Charging (1) Remove the alarm from the installation (2) Remove the screws of the battery compartment and open the hatch cover (3) Use 5V/1A power supply to charge the device, and the charging time is 9 hours
04
Get Started
1. Download APP Download the "Smart life" app from APP Store or Google Play to your mobile
3. Add Devices 3-1. Add ZigBee Gateway Configure to Tuya gateway, please follow the gateway manual (note the difference between wired gateway and wireless gateway)
3-2. Add Sub-devices(Outdoor Siren) Please confirm that the device is in the standby state before configuration. If it is not in the standby state, you need to press and hold the reset button for 6 seconds, and the device indicator light will flash and enter the standby state.
2. Register and Login 2-1 Launch the "Smart life" app. 2-2 To register,enter your mobile phone number or email
address,create a password ,then login to the app. 2-3 Login if you have an account already.
06
07
08
09
Functions and Settings
Normal
Alarm
1. Alarm State Display Click to remove the alarm when it is reported.
2. Record you can view the alarm history record of the device.
3. Smart Setting smart linkage
4. More Setting
10
11
12
Charge state: Normal state/Charging
Set the alarm duration; setting range 1-60min
Tamper alarm; Alarm ringtone; Tamper alarm ;turn on/off the display the current there are 3 alarm tamper alarm, and the tamper will not tamper alarm status sounds to choose be triggered after closing
Other Function 1. Share device
1
3 2
13
2. Push Notification Setting If it is disabled, all devices in the APP will not receive notification, but message records will not be affected.
3
14
3. Remove Device Wipe data; Delete the device through the APP and add the device again to clear the historical record
Alarm switch; turn on/off the alarm
Battery level display
Alarm type
Alarm off; turn on/off the alarm, you will not receive a push after closing, and the device function will not be turned off
4
5
15
16
2 1
18
Due to the app update, the above interface is for reference only 19
Adobe PDF library 15.00 Adobe Illustrator(R) 17.0