Nanlux Evoke 2400B LED Bi-Color Spot Light User Manual

1. Product Name

LED Bi-Color Spot Light

Model No.: Evoke 2400B

2. Technical Data

• Input: AC 100-240V 50/60Hz
• Output: DC 48V 2 x Max. 26A 2496W
• Color Temperature: 2700-6500K
• CRI: 96
• TLCI: 97

3. 2.4G, Bluetooth and LUMENRADIO Remote Control

The Evoke 2400B can be remotely controlled by a 2.4G remote controller, or by the NANLINK APP via a transmitter box or directly via Bluetooth. It also features a built-in LumenRadio module, enabling it to receive CRMX wireless DMX signals.

Note:

• The 2.4G remote controller and transmitter box are sold separately.
• The fixture supports the 2.4G wireless protocol V1.0 and V2.0. Set the fixture to V2.0 when using WS-RC-C1 or WS-RC-C2 remote controllers. Set the fixture to V1.0 when using other remote controllers.

4. Safety Precautions

1. Please open the package to check for damage caused in transit. If damaged, do not use and contact the place of purchase or manufacturer as soon as possible.
2. Do not use a power cord with damaged insulation. Do not unplug forcefully or drag the power cord directly.
3. Ensure that the power supply voltage used matches the voltage designated by the light before installation.
4. Turn the light off when it is not in use or before cleaning.
5. Keep the light safely stored and away from children.

5. Notice

1. Remove the COB protective cap before use.
2. Do not look directly at the emitter when the light is on.
3. Wait 10 seconds after any parameter setting before turning off the light fixture to save the settings for future use.
4. Do not place any objects on the light emitter or allow liquid to flow inside the fixture or the emitter.
5. Do not place the light fixture near flammable substances like alcohol or gasoline.
6. Wipe off debris or dirt using a cloth with clean water or a neutral cleanser when cleaning the light.
7. The fixture should be used in a dry and ventilated place. Avoid using it in damp, dusty, or overheated environments. Ensure the fan and vents are not blocked or obstructed.
8. Any attempt to repair the fixture yourself will void the warranty. Disassembly and repair are only permitted when trained professionals are involved under strict protocols regulated in this manual.
9. For optimal cooling, do not cover the vents when using the fixture, as this may result in equipment damage. The fixture surface temperature can be high after prolonged use; exercise caution to prevent burns and scalds.

6. FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be installed and operated with a minimum distance of 20 cm between the radiator and your body.