User Manual for FOAMit models including: FG-10N-2, FG-10NK-2, FG-10NV-2, FG-10NK-2 10 Gallon Air Operated Portable Fog Equipment, 10 Gallon Air Operated Portable Fog Equipment
USER MANUAL MODEL NUMBER: FG-10N-2 FG-10NK-2 FG-10NV-2 AND RELATED UNITS 10 Gallon Air Operated Portable Fog Equipment English (Original Instructions)
All documents: Misting units - Nilfisk FOOD
USER MANUAL MODEL NUMBER: FG-10N-2 FG-10NK-2 FG-10NV-2 AND RELATED UNITS 10 Gallon Air Operated Portable Fog Equipment English (Original Instructions) User Manual: Portable Fog Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT WARNING Read this manual completely and understand the machine before operating or servicing it. · Read all instructions before installing or operating unit. · Always wear appropriate personal protective equipment (PPE) when operating or servicing unit. · Always follow all chemical safety precautions and handling instructions provided by the chemical manufacturer and Safety Data Sheet (SDS). · If this unit is modified or serviced with parts not listed in this manual, the unit may not operate correctly. · Always depessurize unit after use (as described in the After Use Instructions). · Do not exceed an incoming air pressure of 100 psi (7 bar). · Do not exceed a fluid temperature of 100°F (37°C). · Always flush the unit with fresh water for 5 minutes when switching from an alkaline to an acid or an acid to an alkaline. · Never use unit with hydrocarbons or flammable products. · Only use clean and dry air. Air must be filtered and free of moisture or pump life will be diminished. If needed, install an air dryer before unit. · Do not use an air lubricator before the unit. · Never use unit if it is damaged or leaking. PROTECT THE ENVIRONMENT Please dispose of packaging materials, old machine components, and hazardous fluids in an environmentally safe way according to local waste disposal regulations. Always remember to recycle. *Specifications and parts are subject to change without notice. Model Number: FG-10N-2, FG-10NK-2, FG-10NV-2 Page 2 of 7 | 02142018 User Manual: Portable Fog Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT OPTIONS Pump Seal Material Santoprene (standard) FG-10N Viton (V) -2 Kalrez (K) Add bold option codes to item number as shown. For standard options, no option code is needed. Examples: · FG-10N-2 (standard unit with Santoprene pump seals) · FG-10NV-2 (unit with Viton pump seals) REQUIREMENTS Compressed air requirements Liquid temperature range Chemical compatibility 50 psi (3.4 bar) with 7 cfm (198.3 l/min) 40-100°F (4.4-37°C) Chemical products used with this equipment must be formulated for this type of application and compatible with unit materials and pump seals. For more information on chemical compatibility, consult the manufacturer or SDS for your product or contact our customer service department. SPECIFICATIONS Power type Chemical pickup type Number of products unit can draw from Suction line length/diameter Capacity Flow rate* Compressed air Draws from pre-mixed solution One product 3/8 in. (9.5 mm) inside diameter 12.5 gallons (47.32 liters) 3.7 gal/hour at each nozzle Pump seals Droplet size Coverage area** Run time from full tank** Number of nozzles Wheel type Santoprene, Viton, or Kalrez 15 microns at 50 psi 1 liter of solution will cover approximately 1000 cubic feet (up to system max of 47,320 cubic feet). Approx. 1.5 hours 2 nozzles Two 10 inch non-marking wheels *Dilution rates and flow rates given are based on chemical with viscosity of water and factory air pressure settings. **Area covered and run time may vary based on humidity, air flow, and product used. Model Number: FG-10N-2, FG-10NK-2, FG-10NV-2 Page 3 of 7 | 02142018 User Manual: Portable Fog Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Operation Instructions Always follow all chemical safety precautions and handling instructions provided by the chemical manufacturer and Safety Data Sheet (SDS). 1. Follow all instructions from chemical manufacturer. Fill the tank with water and the advised percentage of chemical concentrate. 2. Place the unit in the area to be fogged. 3. Ensure the air supply valve (BVB14) is in the closed position, and connect a compressed air line to the air inlet fitting (AP25). 4. Open the air supply valve (BVB14) to activate the unit. 5. Evacuate the area. 6. After the unit has stopped fogging, observe all appropriate safety precautions before reentering area. Close the air supply valve (BVB14) and disconnect the compressed air line from the unit. After Use Instructions: 1. Flush the unit with fresh water for 5 minutes. 2. Disconnect the air line from the air fitting (AP25). Maintenance Instructions: To keep your portable unit operating properly, periodically perform the following maintenance procedures: · Check the air pump (P56/P56K/P56V) for wear and leaks. · Inspect hoses for leaks or excessive wear. Make sure all hose clamps are in good condition and properly secured. · Check the suction tube and screen for debris and clean as needed. · Drain compressor tank on a regular basis to ensure proper operation of pump. Troubleshooting Instructions: · If air passes through the pump (P56/P56K/P56V) without cycling, the pump needs to be replaced. · Check the chemical suction line and strainer for debris or damage. Clean or replace as needed. To prevent damage to the unit, the strainer (STR38-IL) must always be used. · Check for proper air pressure on air gauge (AG100). Air regulator (R14) is factory set at 50 psi (3.4 bar). · If the unit foams at a reduced pressure: o Check the air compressor supplying the unit. If the pressure is less than 40 psi, turn the foam unit off until the compressor can catch up. o If the air supply is 50 psi (3.4 bar) or above, check the AG100, which should read near 50 psi (3.4 bar). If the AG100 is more or less than 50 psi (3.4 bar), adjust the pressure by turning the knob on the top of the air regulator (R14). Model Number: FG-10N-2, FG-10NK-2, FG-10NV-2 Page 4 of 7 | 02142018 User Manual: Portable Fog Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT TANK ASSEMBLY ITEM NUMBER: TANK-10N-A DFP7 (see parts list for color options) TANK-10N DP-A OPTIONAL COMPONENTS AIR HOSE ASSEMBLY ITEM NUMBER: AH30 COT FWAX15 W15 AS1-VS SSP12 SSAXLE14 PVCV34FM WATER SEPARATOR ITEM NUMBER: WS-20CFM Model Number: FG-10N-2, FG-10NK-2, FG-10NV-2 Page 5 of 7 | 02142018 User Manual: Portable Fog Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Plate - Inside View FOG NOZZLE ASSEMBLY P56, P56K or P56V R14 AG100 QFEL1438 HBSSEL1814 PFN-N130 EL14M14F QF1438 QFSEL38 STR38-IL QFBH38 QFSEL38 HBSSEL1438 HHPB3414 PVCV34FM Plate - Back View SSA14 BEL14M14M BVB14 AP25 QFSEL38 QFSEL38 FG-10N-2-BRKT QFT38 H38CP (Available per ft.) Model Number: FG-10N-2, FG-10NK-2, FG-10NV-2 Page 6 of 7 | 02142018 User Manual: Portable Fog Units | English READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT ITEM NUMBER AG100 AH30 AP25 AS1-VS B103234 B8X58 BEL14M14M BPS-58SO BPS-SSR BVB14 COT DFP7 DFP7-C DFP7-F DFP7-PIN DFP7-C-BL DFP7-C-GN DFP7-C-RD DFP7-C-YL DP-A DP DP-G EC14-2 EL14M14F FG-10N-2-BRKT FMS1034 FWAX15 FWLG14 H38B-F H38CP HBBEL1414 HBSSEL1438 HHBB1418 DESCRIPTION 1.5 INCH DRY MODEL 20 DUAL SCALE GAUGE 30 FT. AIR HOSE WITH QUICK CONNECT FITTINGS PLUG 1/4 NPTM AIR FITTING - BRASS 1/4-20 X 1/2 PHIL TRUSS MACH SCREW 19-8 W/516 ORANGE VIBRASEAL PATCH 10-32 X 3/4 PHIL TRUSS MACH SCR 18-8 8-15 X 5/8 inch PHIL FLAT TY-A 316 S.S. BRASS ELBOW 1/4in MPT X 1/4in MPT Back Panel Screw - 5/8 inch with Stand Off 1/4 INCH PUSHNUT BOLT RETAINER STAINLESS STEEL AIR INLET VALVE - VA BRS 025-4F4F-BT, NICKEL 1/8 X 1 COTTER PIN 18-8 S/S 7 INCH HINGED CAP ASSEMBLY - INCLUDES BLACK CAP, LID FLANGE AND HINGE PIN 7 INCH FILL CAP POLYPRO BLACK 7 INCH TANK LID FLANGE POLYPRO HINGE PIN FOR DFP7-C & DFP7-C 7 INCH FILL CAP POLYPRO BLUE PANTONE 7 INCH FILL CAP POLYPRO GREEN PANTONE 7 INCH FILL CAP POLYPRO RED PANTONE 7 INCH FILL CAP POLYPRO YELLOW PANTONE DRAIN PLUG ASSEMBLY FOR TANK-10N TANK-20N FRONT DRAIN PLUG FOR PORTABLE UNIT POLYPRO FKM SQUARE CUT DRAIN PLUG GASKET OETIKER CLAMP 13.8 1/4 FEM PIPE X 1/4 M PIPE ELBOW BRACKET FOR FG-10N-2 10 X 3/4in PHIL SHEET METAL SS SCREW FLAT AXLE WASHER .569 ID X 1.28 OD X .08 THICK FLAT WASHER SS 18-8 3/8 INCH BLUE HOSE-HYBRID TPE-Available per ft. 3/8IN OD POLYETHYLENE TUBING - NATURAL HOSE BARB 1/4 MPT X 1/4 BARB ELBOW STAINLESS HOSE BARB ELBOW 1/4 INCH NPT X 3/8 HOSE BARB HEX HEAD BUSHING 1/4 MPT X 1/8 FPT HHPB3414 P56 P56K P56V 20756103B HB14P HB5638 HB5638K HB5638V PFN-N130 PLPF-B PLPF-PIN PVCV34FM QF1438 QF5638 QFBH38 QFEL1438 QFSEL38 QFT38 R14 SSA14 SSAXLE14 SSC38 SSP12 STR38-IL TANK-10N TW916 W15 WS-20CFM HEX HEAD POLY REDUCER BUSHING 3/4 X 1/4 5700 PUMP WITH SANTOPRENE SEALS - INCLUDES HOSE BARBS, AIR FITTING, AND AIR PORT 5700 PUMP WITH KALREZ SEALS - INCLUDES HOSE BARBS, AIR FITTING, AND AIR PORT 5700 PUMP WITH VITON SEALS - INCLUDES HOSE BARBS, AIR FITTING, AND AIR PORT Polypro G57 Air Port x HB Straight, w/ Viton o-ring 1/4in BRASS HB AIR FITTING /G57/P56 HOSE BARB FOR P56 PUMP HOSE BARB FOR P56K PUMP HOSE BARB FOR P56V PUMP PNEUMATIC FOG NOZZLE - POLYPROPYLENE AND KYNAR TIP - 3.7 GAL/HR PER NOZZLE BLANK PORTABLE FOAMER PLATE WITH HINGE W/O HOLES 302 STAINLESS PORTABLE PLATE HINGE PIN PVC VALVE 3/4in FPT X 3/4in MPT MALE CON. 3/8in TUBE X 1/4in MPT - POLYPROPYLENE 3/8in QF PUMP FITTING / G57 BULKHEAD 3/8in TUBE POLYPROPYLENE FIXED ELBOW 3/8in TUBE X 1/4in MPT POLYPROPYLENE PLUG-IN ELBOW 3/8in TUBE X 3/8in POLYPROPYLENE UNION TEE 3/8in TUBE POLYPROPYLENE 1/4 NPTF REGULATOR W/ FILTER-NO GAUGE SS304 MALE/FEMALE ADAPTOR 1/4 NPT X 1/4 NPT 14 ½" long with the 5/8" diameter bar & 2 through holes with countersinks beveled ends WORM GEAR CLAMP, S/S (.25-.63) STAINLESS STEEL AXLE PLATE - 2.5 inch X 1 inch - 2 HOLE IN LINE STRAINER 3/8 BARB 20 MESH 304 STAINLESS EDPM GSKT 10 GALLON NATURAL TANK 1/2 INT TOOTH L/W 410SS NONMARKING WHEEL FOR PORTABLE UNITS TSUNAMI WATER SEPARATOR 20 CFM Model Number: FG-10N-2, FG-10NK-2, FG-10NV-2 Page 7 of 7 | 02142018GPL Ghostscript 9.55.0 Adobe InDesign CS6 (Windows)