Assembly Instructions

CARE INSTRUCTIONS

WIPE CLEAN WITH A SOFT DAMP CLOTH. NEVER USE SCOURERS, ABRASIVES OR CHEMICAL SOLVENTS. KEEP AWAY FROM MOISTURE AND DIRECT SUNLIGHT. STORE IN A DRY PLACE. FOR INDOOR USE ONLY.

WARNING

DO NOT STAND, SIT OR LEAN ON THE UNIT. DO NOT USE THIS UNIT AS A STEP LADDER. ENSURE THIS UNIT IS USED ONLY ON A FLAT SURFACE. DO NOT USE THIS UNIT UNLESS ALL BOLTS AND SCREWS ARE FIRMLY SECURED. DO NOT PLACE HOT OBJECTS SUCH AS COFFEE CUPS DIRECTLY ON THE SURFACE OF THIS FURNITURE ITEM. THIS ITEM IS FOR STORAGE PURPOSES ONLY. CONTAINS SMALL PARTS. IT IS TO BE ASSEMBLED BY AN ADULT. FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.

MAXIMUM SAFE LOAD: 10KG FOR TOP, 5KG FOR DRAWER.

1 Hardware List

• A: 6x30mm - 10pcs
• B: 5x40mm - 4pcs
• C: 4x30mm - 8pcs
• D: 6x35mm - 14pcs
• E: 15x10mm - 14pcs
• F: 4x40mm - 1pc
• G: 6x12mm - 8pcs
• H: M3mm - 1pc
• I: 1pc
• J: 2pcs
• K: 2pcs
• L: 2pcs
• M: 2pcs
• N: 3x12mm - 29pcs
• O: 3x14mm - 4pcs
• P: 4pcs
• Q: 1pc
• R: 2pcs
• S: M4mm - 1pc

2 Parts List

• Part 1: 1pc
• Part 2: 1pc
• Part 3: 1pc
• Part 4: 1pc
• Part 5: 1pc
• Part 6: 1pc
• Part 7: 4pcs
• Part 8: 2pcs
• Part 9: 2pcs
• Part 10: 2pcs
• Part 11: 2pcs
• Part 12: 2pcs

Assembly Steps

ATTENTION: DO NOT TIGHTEN THE SCREWS FULLY DURING ASSEMBLY. FULLY TIGHTEN SCREWS AFTER THE FINAL ASSEMBLY STEP.

STEP 1

Attach parts 9 and 10 to part 2 using screws J (x2), K (x2), and N (x16).

STEP 2

Attach parts 2 and 3 to the base using screws D (x2).

STEP 3

Attach part A (x1) and part E (x1) to part 2.

STEP 4

Attach part A (x1) and part E (x1) to the side panel.

STEP 5

Attach parts 1 and 2 to the main body using screws A (x4), D (x4), and E (x4).

STEP 6

Place part 5 onto the assembled unit.

STEP 7

Attach part 4 to the unit using screws A (x4), B (x4), and H (x1).

STEP 8

Insert dowels G (x8) into the designated holes. Secure with screws S (x1).

STEP 9

Assemble the drawer components using screws C (x8). This step is repeated twice (x2).

STEP 10

Assemble the drawer runners and drawer box. Use screws D (x8), E (x8), L (x2), M (x2), and N (x12). This is done twice (x2).

STEP 11

Insert the assembled drawers into the bedside table unit.

STEP 12

Secure the unit using screws N (x1), P (x4), O (x4), Q (x1), and R (x1).

STEP 13

Attach the back panel using screws R (x1), F (x1), and I (x1).

TOPPLING FURNITURE WARNING

• ALWAYS secure it with an anchor device.
• Please seek professional advice if you are in doubt of what fixing device to use.
• Regularly check that anchors are securely maintained.
• Use safety drawer locks to prevent children climbing.
• Stability of tall items may be affected by thick pile carpet or uneven floors.
• Do not place unanchored televisions on furniture.

CAUTION

For your safety when attaching the anchor fixings, please note the following:

• Check any electrical wires or plumbing inside the wall before drilling any holes (if you are unsure please seek professional advice from a qualified tradesperson).

WARNING: PLEASE SECURE YOUR FURNITURE WITH THE SUPPLIED WALL FIXING. SCAN THE CODE FOR MORE INFORMATION.

This is a permanent label. Do not remove!