Installation Guide for Rydeen models including: BSS-ONE Single Sensor Blind Spot Detector, BSS-ONE, Single Sensor Blind Spot Detector, Blind Spot Detector, Spot Detector
6 | BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles English Installation Guide 5. INSTALLATION 4. Pass the harness through the grommet ensuring the harness and connector do not become damaged. Route the harness to the desired location which the Control Unit will
lightingtrendz.com: RYDEEN BSS-ONE SINGLE SENSOR BLIND SPOT DETECTOR
Lighting Trendz: RYDEEN BSS-ONE SINGLE SENSOR BLIND SPOT DETECTOR
File Info : application/pdf, 12 Pages, 615.17KB
DocumentDocumentEnglish Installation Guide CONTENTS 1. WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. SYSTEM CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3. SYSTEM SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4. SYSTEM LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5. INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.1 TOOLS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.2 SYSTEM BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 6. ERROR DIAGNOSTICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 REV: 0720 English Installation Guide 1. WARNING 1. THE UNIVERSAL BLIND SPOT DETECTION SYSTEM DOES NOT REPLACE ANY FUNCTIONS DRIVERS SHALL ORDINARILY PERFORM IN DRIVING A MOTOR VEHICLE, NOR DOES IT DECREASE THE NEED FOR DRIVERS TO STAY VIGILANT AND ALERT IN ALL DRIVING CONDITIONS, TO OBEY ALL THE SAFE DRIVING STANDARDS, PRACTICES, TRAFFIC RULES AND REGULATIONS. 2. CUB DOES NOT GUARANTEE 100% ACCURACY IN THE DETECTION OF VEHICLES OR PEDESTRIANS, AND THEREFORE DOES NOT GUARANTEE THE PERFORMANCE OF ANY RELATED AUDIO OR VISUAL WARNING SIGNALS. FURTHERMORE, ROAD, WEATHER AND OTHER CONDITIONS MAY ADVERSELY AFFECT THE VEHICLE'S BLIND SPOT DETECTION SYSTEM RECOGNITION AND RESPONSE CAPABILITIES. 3. CAREFULLY READ THIS INSTALLATION GUIDE AND ITS IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLING OR USING THE BSD SYSTEM. 4. IT IS RECOMMENDED THAT THE INSTALLATION BE CARRIED OUT BY QUALIFIED PERSONNEL. Wear proper protective gear Deburr edges and use grommets Use appropriate torque to fasten lb-ft Do not pull the connectors with excessive force. Do not pull the harness with excessive force. Fasten all connectors and terminals securely. Stress relieve harnesses and secure properly. BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles | 1 English Installation Guide 2. SYSTEM CONTENTS No. ITEM Qty 1 Right Universal Blind Spot Sensor 1 2 Left Universal Blind Spot Sensor 1 3 Control Unit 1 4 Right Indicator 1 5 Left Indicator 1 6 Buzzer 1 7 Power Button 1 8 Harness Set 1 9 OBD II Cable 1 10 Manual Set/Accessories 1 PICTURE 2 | BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles English Installation Guide 3. SYSTEM SPECIFICATIONS No. ITEM 1 Operating Temperature 2 Storage Temperature 3 Environmental Protection Level 4 Input Voltage Range 5 Current Consumption 6 Alarm Level 7 Accuracy of Alarm 8 Specifications 9 Radiation Regulations 10 Buzzer 11 Warning Indicator SOUND SPECIFICATIONS -40ºC~ +85ºC -40ºC ~ +90ºC RadarjIP67 12V (9V 16V) 500mA@12V ; 6. 0W Level I jLED On (Constant) Level IIjLED Flash+Buzzer On Vehicle: >99% ISO 17387/IS0 16750 FCC / NCC / VSCC 75dB 5V Drive, A Pillar 4. SYSTEM LAYOUT [ OBD II ] [ POWER BUTTON ] [ BUZZER ] [ LEFT INDICATOR ] [ RIGHT INDICATOR ] [ CONTROL UNIT ] [ LEFT BLIND SPOT SENSOR ] [ RIGHT BLIND SPOT SENSOR ] BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles | 3 English Installation Guide 5. INSTALLATION 5.1 TOOLS REQUIRED Painter's Tape Plastic Pry Bars Philips & Flathead Screwdrivers Surface Cleaner (i.e. rubbing alcohol) Tape Measure Level Sockets & Wrenches Rags Pliers & Cutters Electric Drill Torque Wrench 1. Look for and use grommets for vehicle access to avoid drilling holes. 2. Ensure all harnesses are fully connected and locked in. 3. Use the cable ties to fasten harness while installing. 5.2 SYSTEM BLOCK [ POWER BUTTON ] [ LEFT INDICATOR ] [ BUZZER ] [ LEFT BLIND SPOT SENSOR ] [ RIGHT INDICATOR ] [ OBD II ] [ RIGHT BLIND SPOT SENSOR ] [ ANALOG CONNECTIONS ] OBD pin 16 (Battery) OBD pin 4 (Chassis Ground) OBD pin 14 (CAN_L) OBD pin 6 (CAN_H) BLUE YELLOW WHITE ORANGE 4 | BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles 12v+ Ignition 12v+ Reverse Right Turn Signal Left Turn Signal English Installation Guide 53.. ISNYSSTTAELMLALTAIOYONUT 5.3 INSTALLATION 1. Measure the rear bumper locating a point suitable for installation which aims the sensor 45 degrees from the centerline of the vehicle. Along that axis, locate a position 19.5 to 28 inches from the ground what is parallel to the ground for the sensor to be installed inside the bumper. Mark this location with painter's tape on the outside of the bumper cover. Face radar toward rear traffic Face radar adhesive side out 45º This side up 2. Remove the bumper cover and clean the inside of the cover where the sensor is to be placed. The area should be cleaned so that the adhesive pad on the sensor assembly may be securely attached. Affix the sensor to the bumper cover taking note of the direction, orientation, and designated location. 3. Connect the left and right radar sensors to the harness. Route the harness assembly from the rear exterior of the vehicle into the cabin utilizing a grommet. Secure the harness away from the heat sources and moving parts. Affix it to the vehicle using cable ties. BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles | 5 English Installation Guide 5. INSTALLATION 4. Pass the harness through the grommet ensuring the harness and connector do not become damaged. Route the harness to the desired location which the Control Unit will be installed. 5. Instructions for A. indicator, B. buzzer & C. BSD power button. A. Select locations for the right & left indicators to be installed, check for clearance behind the panel. Mark the locations to be drilled with the provided tool. Drill holes. Snap into place. B. Locate a suitable location for the buzzer around the A pillar for maximum effect and ease of installation. Affix the buzzer using the adhesive patch or wire ties. C. Locate a suitable location for the BSD power button which is accessible to the driver, inspect the area behind the panel for clearance. Drill a hole for the button and insert the button into the hole. 6 | BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles English Installation Guide 5. INSTALLATION 6. Locate the OBD-II connector and connect the adapter to the socket. Route the harness to the desired location for the Control Unit to be installed. 7. Connect IGN lead to a switched power source (i.e. cigarette lighter, radio accessory power, ignition switch). Connect REVERSE lead to the 12v+ reverse source (i.e. reverse light circuit, integration module output). Connect DIRECTION R and DIRECTION L leads to their corresponding turn signal sources (i.e. tail lamp, side marker, front turn signal). The turn signal leads also accept PWM signal sources in most cases. 8. Connect all the connections then route the harness to the Control Unit and affix the unit in a safe location in the vehicle (i.e. under the dashboard, under the seat, inside the console). Connect the harness connector to the Control Unit. BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles | 7 English 6. ERROR DIAGNOSTICS It is possible that the Blind Spot Detection System will trigger an alert even though there is no vehicle in the blind spot zone. The Blind Spot Detection System can detect objects such as: construction barrels, guard rails, lamp posts, etc. Occasional false alerts are normal. STATUS Controller HMI CAN TX Failed Radar System Error Sleep Mode System Initialization SOUND Do Re Mi Do Re Mi 1 second beep, stop .5 second & 1 second beep 3 second beep Installation Guide 8 | BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles English Installation Guide 7. TROUBLESHOOTING ISSUE SYMPTOM The system does not respond after starting the engine Power On Self-test The indicator does not light up The buzzer makes no sound The power switch does not work System Operation [ Do Re Mi ]alarm Did not enter sleep mode after 5 minutes of IGN off No Level 1 BSD alert Functions No Level 2 BSD alert No RCTA alert POSSIBLE CAUSE Incorrect connection or control unit failure Damaged indicator Disconnected indicator Damaged buzzer Disconnected buzzer Damaged power switch Disconnected power switch Radar disconnection or no OBD connection IGN lead connected to constant power Vehicle speed is less than 12 mph Bad connection from OBDII Turn signal leads not connected Reverse lead not connected POSSIBLE SOLUTION Confirm that the IGN, wiring, fuse, and controller are connected. Contact your dealer Verify connection Contact your dealer Verify connection Contact your dealer Verify connection, press and hold the switch for 2 seconds. Abnormal power supply, wiring, or radar, please contact your dealer. Change the IGN to a switched power source connection location Normal operation The vehicle is not compatible. Please contact the dealer. Press the RESET button on the control unit after starting the engine. Check the system again after the reboot is completed. Confirm turn signal leads are connected Confirm that the reverse lead is connected BLIND SPOT DETECTION SYSTEM: For Passenger Vehicles | 9 250 Benton Ct, City of Industry, CA · 714.784.6687 · www.buyblindspot.com · cs@novusradar.com