Instruction Manual for FULHAM models including: VKMUNV008RT930A VividHorse Universal Voltage 120-277V DC Engine Retrofit Kit, VKMUNV008RT930A, VividHorse Universal Voltage 120-277V DC Engine Retrofit Kit, 120-277V DC Engine Retrofit Kit
Fulham: DC LED Retrofit Kits
Fulham: Specification Sheets
File Info : application/pdf, 6 Pages, 2.31MB
DocumentDocumentLED LIGHT ENGINE APPLICATION PROGRAM RETROFIT KIT INSTALLATION MANUAL FOR CEILING MOUNTED LUMINAIRES INSTALLATION INSTRUCTIONS VividHorse Universal Voltage (120-277V) DC Engine Retrofit Kit VKMUNV008RT930A VKMUNV018RT930A Reference spec sheet for full part numbers Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 order@fulham.com www.fulham.com Installation Instructions subject to change without notice. Page 1 of 6 01/06/22 INS-VKM-RD_V3, Rev A LED LIGHT ENGINE APPLICATION PROGRAM RETROFIT KIT INSTALLATION MANUAL FOR CEILING MOUNTED LUMINAIRES 1.0 INSTALLATION WARNINGS 1. "THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND HAZARDS INVOLVED." 2. "WARNING - Risk of fire or electric shock. LED Retrofit kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician." 3. "WARNING - Risk of fire or electric shock. Install this kit only in the luminaires that has the construction features and dimensions shown in the photographs and/or drawings." 4. "WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects." 5. "WARNING Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components." 6. "CAUTION RISK OF FIRE. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR." 7. THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS 8. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components. 1.0 AVERTISSEMENTS D'INSTALLATION 1. CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS. 2. AVERTISSEMENT - Risque d'incendie ou de choc électrique. L'installation de ce nécessaire de modernisation exige une personne familière avec la construction et le fonctionnement du système électrique du luminaire et des risques associés. Toute personne qui n'est pas qualifiée ne doit faire aucune tentative d'installation et doit contacter une personne qualifiée. 3. AVERTISSEMENT - Risque d'incendie ou de choc électrique. N'installer ce nécessaire que dans les luminaires ayant les caractéristiques de construction et les dimensions sont conforme à celles illustrées dans les photos et/ou les dessins 4. AVERTISSEMENT - Afin de prévenir l'endommagement ou l'abrasion des câbles, éviter tout contact entre ces derniers et le bord d'un objet tranchant tel qu'une tôle. 5. "AVERTISSEMENT -Risk d'incendie ou de choc électrique. Le câblage du luminaire et les pièces électriques peuvent être endommagés lors du forage pour l'installation d'un kit de reconditionnement LED. Vérifiez le câblage et les composants inclus. " 6. ATTENTION RISQUE D'INCENDIE, CONSULTER UN ÉLECTRICIEN QUALIFIÉ POUR VOUS ASSURER QUE LES CONDUCTEURS DE LA DÉRIVATION SONT ADÉQUATS. 7. LE KIT DE RÉNOVATION EST ACCEPTÉ COMME COMPOSANT D'UN LUMINAIRE LORSQUE L'ADAPTATION DU LA COMBINAISON EST DÉTERMINÉE PAR CSA OU LES AUTORITÉS AYANT JURIDICTION. PRODUIT DOIT ÊTRE INSTALLÉ PAR UN ÉLECTRICIEN QUALIFIÉ CONFORMÉMENT AUX NORMES APPLICABLES ET CODES ÉLECTRIQUES APPROPRIÉS. LE GUIDE D'INSTALLATION NE REMPLACE PAS LOCAL OU REGLEMENTATION NATIONALE DES INSTALLATIONS ELECTRIQUES 8. Seuls les trous ouverts indiqués sur les photographies et/ou les dessins peuvent être réalisés ou modifiés à la suite du kit installation. Ne laissez aucun autre trou ouvert dans un boîtier de câblage ou de composants électriques. Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 order@fulham.com www.fulham.com Installation Instructions subject to change without notice. Page 2 of 6 01/06/22 INS-VKM-RD_V3, Rev A LED LIGHT ENGINE APPLICATION PROGRAM RETROFIT KIT INSTALLATION MANUAL FOR CEILING MOUNTED LUMINAIRES 2.0 CCT SELECTION INDICATION 1. The VividHorse DC Engine Retrofit Kit is a dual-channel LED product, that allows for CCT selection via the dip switch on the PCB. Available CCTs include 2700K, 3000K, 3500K, 4000K, 4500K and 5000K. 2. A pre-set CCT will come from the factory. Check the product label or packaging to see the pre-set CCT level. 3. Change the dip switch position to "ON" (1~6) to set the desired CCT level. NOTE: ONLY keep one dip switch in the "ON" position, not doing so may result in an undesired CCT. CCT Selection Dip Switch CCT Indication Table 2700K 3000K 3500K 4000K 4500K 5000K 1 ON OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF 3 OFF OFF ON OFF OFF OFF 4 OFF OFF OFF ON OFF OFF 5 OFF OFF OFF OFF ON OFF 6 OFF OFF OFF OFF OFF ON 2700K 3000K 3500K 4000K 4500K 5000K OFF OFF OFF OFF OFF OFF CCT ON 50 45 40 35 30 27 CCT ON 50 45 40 35 30 27 CCT ON 50 45 40 35 30 27 CCT ON 50 45 40 35 30 27 CCT ON 50 45 40 35 30 27 CCT ON 50 45 40 35 30 27 Retrofit Kit Warning Label This luminaire has been modified and can no longer operate the originally intended lamp. REPLACE ONLY WITH FULHAM ELECTRONIC CO. : VKMUNV0**RT930A Ce luminaire a été modifié et ne peut plus utiliser la lampe prévue à l'origine. REMPLACER UNIQUEMENT AVEC FULHAM ELECTRONIC CO. : VKMUNV0**RT930A Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 order@fulham.com www.fulham.com Installation Instructions subject to change without notice. Page 3 of 6 01/06/22 INS-VKM-RD_V3, Rev A LED LIGHT ENGINE APPLICATION PROGRAM RETROFIT KIT INSTALLATION MANUAL FOR CEILING MOUNTED LUMINAIRES 3.0 ORIGINAL LUMINAIRE DIMENSIONS Original Luminaire Mfr: Indessa Lighting - Model: 562 Series Minimum Luminaire Dimensions 10.5" 4.25" 6.0" Remove all the original luminaire parts, hardware, lamp, ballast, and socket in order to begin the retrofit. Original luminaire diffuser and original ground wire will need to be kept for this retrofit. This DC Engine Kit can be retrofitted into any surface wall or ceiling luminaire with a similar shape and diameter/height greater or equal to the minimum dimensions described above, or volume greater or equal to 158.66 cubic inches. 4.0 RETROFIT KIT COMPONENTS Retrofit kit components will be provided as listed below: UNV DC Engine Mounting Hardware This luminaire has been modified and can no longer operate the originally intended lamp. REPLACE ONLY WITH FULHAM ELECTRONIC CO. : VKMUNV0**RT930A Ce luminaire a été modifié et ne peut plus utiliser la lampe prévue à l'origine. REMPLACER UNIQUEMENT AVEC FULHAM ELECTRONIC CO. : VKMUNV0**RT930A Input Power Connector Retrofit Warning Label 5.0 RECOMMENDED TOOLS (Not Included) Power Drill W/ Philips Bit Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 order@fulham.com www.fulham.com Installation Instructions subject to change without notice. Page 4 of 6 01/06/22 INS-VKM-RD_V3, Rev A LED LIGHT ENGINE APPLICATION PROGRAM RETROFIT KIT INSTALLATION MANUAL FOR CEILING MOUNTED LUMINAIRES 6.0 RETROFIT KIT DESCRIPTION A B C D This luminaire has been modified and can no longer operate the originally intended lamp. REPLACE ONLY WITH FULHAM ELECTRONIC CO. : VKMUNV0**RT930A Ce luminaire a été modifié et ne peut plus utiliser la lampe prévue à l'origine. REMPLACER UNIQUEMENT AVEC FULHAM ELECTRONIC CO. : VKMUNV0**RT930A ITEM A. B. C. D. DESCRIPTION DC Engine 6-20 X 3/8" Pan Head Self Drilling Screws Input Connector Retrofit Labels QTY 1 4 1 2 Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 order@fulham.com www.fulham.com Installation Instructions subject to change without notice. Page 5 of 6 01/06/22 INS-VKM-RD_V3, Rev A LED LIGHT ENGINE APPLICATION PROGRAM RETROFIT KIT INSTALLATION MANUAL FOR CEILING MOUNTED LUMINAIRES 7.0 RETROFIT KIT ASSEMBLY 1. Start by removing the original lamp, ballast and socket from the luminaire. See Figure 1. NOTE: The original luminare ground wire will need to be kept for this retrofit. 2. Pass the DC Engine (A) input power wires and dimming wires (if available) through the luminaire wire hole. See Figure 2. 3. Place the DC Engine (A) onto the luminaire back plate as shown in Figure 3. NOTE: LED Engine must make direct contact with the back plate when installed in order to provide sufficient heat sinking to properly manage thermals for safety and warranty purposes. Figure 1 Figure 2 4. Use the supplied self-drilling screws (B) to attach the DC Engine (A) to the luminaires housing. See Figure 4. 5. Place the provided labels in the outer space of the luminaire after the DC Engine installation has been completed. Labels must be clearly visible and should not be obscured by line voltage cables. See Figure 5. Figure 3 can no lamp. Figure 4 ERLEEPLCTARCEONIOCNLCYO.W:ITVHKFMUULNHVA0*M*RT930A been modified and originally intended has the This luminaire longer operate Ce luminaire a été modifié et ne peut plus utiliser la lampe prévue à l'origine. REMPLACER UNIQUEMENT AVEC FULHAM ELECTRONIC CO. : VKMUNV0**RT930A 6. Completed assembly should look like Figure 5. 7. Luminaire is now ready to be installed. Please see below for instructions on connecting line voltage to the luminaire. Re-attach and secure the lens once installation is completed, retrofit should look like Figure 6. Figure 5 This luminaire has been modified and can no longer operate the originally intended lamp. REPLACE ONLY WITH FULHAM ELECTRONIC CO. : VKMUNV0**RT930A Ce luminaire a été modifié et ne peut plus utiliser la lampe prévue à l'origine. REMPLACER UNIQUEMENT AVEC FULHAM ELECTRONIC CO. : VKMUNV0**RT930A Figure 6 Connecting Power to the DC Engine: 1) Connect the green wire (Ground) from the luminaire to the Ground that is being fed by the power source. Connect these two wires by using a wire connector with a minimum 18AWG rating. 2) Connect the white wire (Neutral) from the LED Engine to the Neutral being fed by the power source. Connect these two wires by using a wire connector with a minimum 18AWG rating. 3) Connect the Black wire (Line) from LED Engine to the Line being fed by the power source. Connect these two wires by using a wire connector with a minimum 18AWG rating. 8.0 WARRANTY Please refer to LED Engine kit spec sheet for warranty information Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 order@fulham.com www.fulham.com Installation Instructions subject to change without notice. Page 6 of 6 01/06/22 INS-VKM-RD_V3, Rev A