IoT Wireless Module Solutions | IoT and M2M Experts in Wireless Embedded WifiIoT Wireless Module Solutions | IoT and M2M Experts in Wireless Embedded Wifi
User Manual for SparkLAN models including: WNFQ268AXBT, RYK-WNFQ268AXBT, RYKWNFQ268AXBT, WNFQ-268AXI, WNFQ-268AX, WNFQ-268AXI WiFi 6 or 6E M.2 Tri Band WiFi Module, WiFi 6 or 6E M.2 Tri Band WiFi Module, 6E M.2 Tri Band WiFi Module, M.2 Tri Band WiFi Module, Tri Band WiFi Module, WiFi Module, Module
SparkLAN Communications, Inc. WNFQ268AXBT RYK-WNFQ268AXBT RYKWNFQ268AXBT wnfq268axbt
File Info : application/pdf, 14 Pages, 482.97KB
DocumentDocumentWireless Module
WNFQ-268AXI(BT)
WNFQ-268AX(BT)
Specification
Standards Chipset Data Rate
Operating Frequency Interface Form Factor Antenna
Modulation
IEEE 802.11ax/ac/a/b/g/n (2T2R) Bluetooth V5.2, V5.1, V5.0, V4.2, V4.1, V4.0LE, V3.0, V2.1+EDR Qualcomm Atheros WCN6856 802.11b: 11Mbps 802.11a/g: 54Mbps 802.11n: MCS0~15 802.11ac: MCS0~9 802.11ax: HE0~11 Bluetooth: 1 Mbps, 2Mbps and Up to 3Mbps IEEE 802.11ax/ac/a/b/g/n ISM Band, 2.412GHz~2.484GHz, 5.150GHz~5.850GHz ,5.925~7.125GHz(FCC only) *Subject to local regulations WLAN: PCIe Bluetooth: USB M.2 2230 E Key and AE key 2 x IPEX MHF4 connectors Ant 1 for WLAN/BT, Ant 2 for WLAN Wi-Fi: 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11n: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11ac: OFDM (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM) 802.11ax: OFDMA (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM) BT: Header: GFSK Payload 2M: /4-DQPSK Payload 3M: 8-DPSK
All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880
WNFQ-268AXI(BT) ver.0.93
Wireless Module
Operating Voltage
DC 3.3V
Operating Temperature Range
WNFQ-268AXI(BT) Operating Temp: -40°C ~75°C; WNFQ-268AX(BT) Operating Temp: -10°C ~65°C
Storage Temperature Range -45°C~90°C
Humidity
5%~90% (Operating)
(Non-Condensing)
5%~90% (Storing)
Dimension L x W x H (in mm) 30mm(± 0.15mm) x 22mm(± 0.15mm) x 3.5mm(± 0.3mm)
Weight (g)
3.2g
Security
64/128-bits WEP, WPA, WPA2, WPA3, 802.1x
All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880
WNFQ-268AXI(BT) ver.0.93
Block Diagram
Wireless Module
Mechanical Dimension (mm)
All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880
WNFQ-268AXI(BT) ver.0.93
Wireless Module
Pin Assignment (TBD)
The following section illustrate signal pin-outs for the module connector.
Pin#
Pin Name
1 GND
3 USB_D+
5 USB_D-
7 GND
9 SDIO_CLK/SYSCLK
11 SDIO_CMD
13 SDIO_DATA0
15 SDIO_DATA1
17 SDIO_DATA2
19 SDIO_DATA3
21 SDIO_WAKE#
23 SDIO_RESET#/TX_BLANKING
25 NOTCH FOR KEY E
27 NOTCH FOR KEY E
29 NOTCH FOR KEY E
31 NOTCH FOR KEY E
33 GND
35 PERp0
37 PERn0
39 GND
41 PETp0
43 PETn0
45 GND
47 REFCLKp0
49 REFCLKn0
51 GND
53 CLKREQ0# (3.3V)
55 PEWAKE0# (3.3V)
57 GND
59 RESERVED/PERp1
TOP
Type
Description
G Ground connections I/O USB serial differential data Positive
I/O USB serial differential data Negative
G Ground connections
NC No Connection
NC No Connection NC No Connection NC No Connection
NC No Connection
NC No Connection
NC No Connection
NC No Connection
NC No Connection NC No Connection NC No Connection
NC No Connection
G Ground connections
I PCI Express receive data-Positive
I PCI Express receive data-Negative
G Ground connections O PCI Express transmit data- Positive O PCI Express transmit data- Negative
G Ground connections
I PCI Express differential clock input- Positive
I PCI Express differential clock input- Negative
G Ground connections
OD PCIe clock request OD PCIe wake signal G Ground connections
NC No Connection
All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880
WNFQ-268AXI(BT) ver.0.93
61 RESERVED/PERn1 63 GND 65 RESERVED/PETp1 67 RESERVED/PETn1 69 GND 71 RESERVED/REFCLKp1 73 RESERVED/REFCLKn1 75 GND
Pin Assignment
Pin#
Pin Name
2 3.3 V
4 3.3 V
6 LED_1#
8 PCM_CLK/I2S_SCK (1.8V)
10 PCM_SYNC/I2S_WS (1.8V)
12 PCM_OUT/I2S_SD_OUT (1.8V)
14 PCM_IN/I2S_SD_IN (1.8V)
16 LED_2#
18 GND
20 UART_WAKE# (3.3V)
22 UART_TXD
24 NOTCH FOR KEY E
26 NOTCH FOR KEY E
28 NOTCH FOR KEY E
30 NOTCH FOR KEY E
32 UART_RXD
34 UART_RTS
36 UART_CTS
38 VENDOR DEFINED
40 VENDOR DEFINED
42 VENDOR DEFINED
44 COEX3
46 COEX_TXD
48 COEX_RXD
Wireless Module
NC No Connection G Ground connections NC No Connection NC No Connection G Ground connections NC No Connection NC No Connection G Ground connections
BOTTOM
Type
Description
P VDD system power supply input P VDD system power supply input O WLAN LED I I2S Continuous Serial Clock (SCK).
I I2S Word Select.
O I2S Serial Data IN. I I2S Serial Data OUT. O Bluetooth LED G Ground connections NC No Connection NC No Connection
NC No Connection
NC No Connection NC No Connection NC No Connection NC No Connection NC No Connection
NC No Connection
NC No Connection
NC No Connection NC No Connection NC No Connection DNC Do Not Connect
DNC Do Not Connect
All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880
WNFQ-268AXI(BT) ver.0.93
Wireless Module
50 SUSCLK 52 PERST0# 54 W_DISABLE2# 56 W_DISABLE1# 58 I2C_DATA 60 I2C_CLK 62 ALERT# 64 RESERVED 66 UIM_SWP/PERST1# 68 UIM_POWER_SNK/CLKREQ1# 70 UIM_POWER_SRC/GPIO_1/PEWAKE1# 72 3.3 V 74 3.3 V
NC No Connection I PCIe host indication to reset the device Active low. I BT enable signal. I WLAN enable signal. NC No Connection NC No Connection NC No Connection NC No Connection NC No Connection NC No Connection NC No Connection P VDD system power supply input P VDD system power supply input
Note: Power (P), Ground (G), Open-Drain (OD), Input (I), Output (O), Do Not Connect (DNC), No Connection (NC)
All Rights Reserved. SparkLAN may make changes to specification and descriptions at any time without prior notice. www.sparklan.com / sales@sparklan.com / +886 2 2659-1880
WNFQ-268AXI(BT) ver.0.93
Installation Connect the Module to the PCIe slot of the computer. Install Wi-Fi driver driver. After the Wi-Fi Driver is installed , click the Network icon on the Windows, then
search the network , and connect the Wireless Network you want.
Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
RF exposure statements This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.
CFR 47 FCC PART 15 SUBPART C (15.247) and SUBPART E (15.407) has been investigated. It is applicable to the modular transmitter.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product.
This radio transmitterRYK-WNFQ268AXBT has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Unique antenna connector must be used on the Part 15 authorized transmitters used
in the host product.
Antenna Type
Brand
Maximum Gain (dBi) Antenna Model
2.4 GHz 5GHz 6GHz
Remark
Length of Antenna
Dipole SparkLAN AD-500AX 2.65 dBi 4.81 dBi 4.98 dBi cable:550mm Connector type of
Antenna cable: I-PEX/MHF4
Length of Antenna
Dipole
SparkLAN
AD-501AX
3.7 dBi
5 dBi
cable:150mm Connector type of 5 dBi
Antenna cable: I-PEX/MHF4 to
RP-SMA
Length of Antenna
PIFA
SparkLAN AD-502AX 3.5 dBi 5 dBi 3.9 dBi cable:300mm Connector type of
Antenna cable: I-PEX/MHF4
Length of Antenna
Dipole SparkLAN AD-503AX 3.7 dBi 5 dBi 5 dBi cable:150mm Connector type of
Antenna cable: I-PEX/MHF4
CHIP SparkLAN 2450AD18A6050 2 dBi 1.5 dBi 2.7 dBi N/A
Dipole SparkLAN
Length of Antenna
AD-504AX 2.67dBi 4.87 dBi 4.94 dBi cable:150mm Connector type of
Antenna cable: I-PEX/MHF4
Dipole SparkLAN
Length of Antenna
AD-505AX 2.67dBi 4.87 dBi 4.94 dBi cable:250mm Connector type of
Antenna cable: I-PEX/MHF4
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use
wording such as the following: "Contains Transmitter Module FCC ID:RYKWNFQ268AXBT" Or "Contains FCC ID:RYK-WNFQ268AXBT"
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the users manual.
The module is for indoor applications only.
The module may not be used for the purposes of remote control of drones
The antenna must be installed into the host device so that the end user does not have access to the antenna or its connector.
Minimum antenna gain, including any cable losses, for the 6GHz bands must exceed 0dBi.
Industry Canada statement: This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: 1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) l'appareil ne doit pas produire de brouillage; 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
Caution: 1) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
3) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
Avertissement: 1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
2) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la imitation P.I.R.E.;
3) Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour l'exploitation point à point et non point à point, selon le cas.
Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This radio transmitter (IC: 6158A-WNFQ268AXBT has been approved by Industry
Canada to operate with the antenna types listed below with the maximum
permissible gain indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use
with this device.
Le présent émetteur radio (IC: 6158A-WNFQ268AXBT a été approuvé par Industrie
Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un
gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le
gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Antenna Type
Brand
Maximum Gain (dBi) Antenna Model
2.4 GHz 5GHz
Remark
Length of Antenna
cable:550mm Dipole SparkLAN AD-500AX 2.65 dBi 4.81 dBi
Connector type of Antenna
cable: I-PEX/MHF4
Length of Antenna
cable:150mm
Dipole SparkLAN AD-501AX 3.7 dBi 5 dBi Connector type of Antenna
cable: I-PEX/MHF4 to RP-
SMA
Length of Antenna
Dipole SparkLAN
AD-310N
cable:550mm 2.65 dBi 4.86 dBi
Connector type of Antenna
cable: I-PEX/MHF4
Length of Antenna
PIFA SparkLAN AD-502AX
3.5 dBi
cable:300mm 5 dBi
Connector type of Antenna
cable: I-PEX/MHF4
Length of Antenna
Dipole SparkLAN AD-503AX
3.7 dBi
cable:150mm 5 dBi
Connector type of Antenna
cable: I-PEX/MHF4
CHIP SparkLAN 2450AD18A6050 2 dBi 1.5 dBi N/A
Length of Antenna
cable:150mm
Dipole SparkLAN AD103AG 2.02 dBi 2.03 dBi Connector type of Antenna
cable: I-PEX/MHF4 to RP-
SMA
Dipole SparkLAN Dipole SparkLAN Dipole SparkLAN Dipole SparkLAN Dipole SparkLAN
AD-302N AD-303N AD-308N AD-504AX AD-505AX
3.14 dBi 3.14 dBi
3 dBi 2.67 dBi 2.67 dBi
Length of Antenna cable:150mm 2.74 dBi Connector type of Antenna cable: I-PEX/MHF4 to RPSMA Length of Antenna cable:150mm 3.24 dBi Connector type of Antenna cable: I-PEX/MHF4 to RPSMA Length of Antenna cable:150mm 5 dBi Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna cable:150mm 4.87 dBi Connector type of Antenna cable: I-PEX/MHF4 Length of Antenna cable:250mm 4.87 dBi Connector type of Antenna cable: I-PEX/MHF4
If the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains IC: 6158A-WNFQ268AXBT".
Si le numéro de certification ISDE n'est pas visible lorsque le module est installé à l'intérieur d'un autre appareil, alors l'extérieur de l'appareil dans lequel le module est installé doit également afficher une étiquette faisant référence au module inclus. Cette étiquette extérieure peut utiliser un libellé comme celui-ci: " Contient IC: 6158A-WNFQ268AXBT".
Plaque signalétique du produit final: Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6158A-WNFQ268AXBT ".
Manual Information To the End User: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manue
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual. Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: RYK-WNFQ268AXBT, Contains IC:6158A-WNFQ268AXBT The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer's instruction manual.
If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes.
le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de montrer dans ce manuel. le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes les autres exigences applicables du système comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans l'hôte. le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID:RYKWNFQ268AXBT, contient IC : 6158A-WNFQ268AXBT