Instruction Manual for LEDALITE models including: MI NatureConnect Daylight Island, NatureConnect Daylight Island, Daylight Island, Island
Current Daylight island max. 1.0A Power 42 W Voltage max. 60 V Dimensions LxWxH [1796x597x99 mm] 70.7x24x3.9 in 15.4 kg (including driver) 34 lb (including driver)
2 sept. 2022 — Note: This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to part 15 of the FCC Rules. These limits are.
File Info : application/pdf, 3 Pages, 3.68MB
DocumentDocumentindoor Daylight island Daylight driver 1x 1x M4 x 10mm 4x 4x 8-18B x 1/4" 6x For mounting Daylights 4x 4x #6 - 5/16" 24x Mounng instrucons Daylight Island NatureConnect Safety cable mechanism Gripper Cable 1x 1x Daylight panel in separate box Tools not included 3 PH2 4X 3/8 Power 42 W Current max. 1.0A L Voltage max. 60 V Dimensions LxWxH 70.7x24x3.9 in [1796x597x99 mm] 34 lb (including driver) 15.4 kg (including driver) W Mounting brackets #6 - 5/16" 4X © 2020 Signify Holding. All rights reserved H 4X 1/3 IMPORTANT: All Mounting brackets (4 each side) need to be installed on Daylight #6 - 5/16" Data subject to change without notice www.signify.com/natureconnect Install driver plate M4 x 10mm 4X Connect driver and screw top box Safety cable installation 8-18B x 1/4" 6X 1. Insert safety cable trough frame part as image 2. Install gripper on backplate cover tab of Daylight 3. Insert cable through gripper 4. Adjust cable length as tight as possible (image as reference) © 2020 Signify Holding. All rights reserved 5. Final position reference length on gripper side 2/3 Data subject to change without notice www.signify.com/natureconnect Safety cable installation IMPORTANT: Do NOT install Daylight without Safety cable 1. Insert cable end thru gripper nut side 2. Adjust to desired cable lenght 3. Lock Gripper nut Inrush current I max I mains (A) max/2 Tref Electrical characteristics Max. inrush Current <200m s I nom. Time (us) MCB B-10 A B-16 A C-10 A C-16 A Max n. of lumin. 22 36 22 36 ATTENTION ! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEE electrical regulations or the national requirements. The light source of this luminaire is not replaceable; when the light source reached its end of life the whole luminaire shall be replaced. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer, his service agent or similar qualified person in order to avoid hazard. During installation or maintaining the luminaire please use gloves to avoid spots on the cover. To remove dust and spots use the following: - Dust: use micro fiber cloths only - Fingerprints, etc.: use a cleaner for synthetic materials with antistatic properties. The product is IPX0 & as such is not protected against water ingress & as such we strongly recommend that the environment in which the luminaire is to be installed is suitably checked. If the above advice is not taken and the luminaires are subject to water ingress, Signify cannot guarantee safe failure & product warranty will become void. Note: This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial enviroment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. © 2020 Signify Holding. All rights reserved 3/3 Data subject to change without notice www.signify.com/natureconnect