Honeywell 7.5ft 600ct Churchill Pine Prelit User Manual

Thank You

Thank you for purchasing The 7.5ft Honeywell Churchill Pine LED One Plug tree. This tree assembles in minutes and is decorated with LED light sets. For your convenience, it is equipped with a foot pedal switch for easy illumination.

Important Safety Instructions

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

• Do not use this product outdoors. This seasonal use product is not intended for permanent installation or use.
• Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.
• Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
• Do not let lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the house, when retiring for the night, or if left unattended.
• This is an electric product—not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not be played with or placed where small children can reach it.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from cord, wire, or light string. Hang ornaments only on the tree itself.
• Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
• Do not cover the product with cloth, paper or any material not part of the product when in use.
• This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
• This product is equipped with push-in type lamps. Do not twist lamps.
• This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be fully inserted. Do not alter or replace the plug.
• Read and follow all instructions that are on the product or provided with the product.

SAVE THESE INSTRUCTIONS.

Package Content

The following items are included in the package:

• Installation Kit:
• Top Section (A) - 1 set
• Middle Section (B) - 1 set
• Bottom Section (C) - 1 set
• Tree Base (D) - 1 set
• Screw (E) - 1 piece

• Other Components:
• Bolt (F) - 2 pieces
• Fuse (G) - 2 pieces
• Replacement lamp (H) - 8 pieces

Diagram Description: The package content section displays illustrations of the tree sections (A, B, C), the tree base (D), a screw (E), bolts (F), fuses (G), and replacement lamps (H).

Installation

Note: Before you start to assemble your tree, please choose a location near an electrical wall outlet. Place the tree stand on a level surface. Please remove protective covers from the base of the pole from each section.

1. Unfold the tree base (D) to a 90 degree angle.
2. Carefully insert the bottom section (C) of the tree into the tree base (D) and tighten the screw (E) (see Figure 1).
3. Insert the middle section (B) of the tree into the bottom section (C) (see Figure 2).
4. Insert the top section (A) into the middle section (B) (see Figure 3).
5. Note: There is a tree top connector on the top section (A).
6. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches, be sure that all wires are free of branch hinges (see Figure 4).
7. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left, and one along the centre of the main stem. Repeat this pattern for each branch (see Figure 5).
8. Plug the well-connected power supply cord plug 1 from the bottom section (C) into an electrical outlet. Please note this tree comes with an on/off foot pedal switch for easy illumination. Plug 2 is for tree top lights. Plug the power supply cord plug 2 into an electrical outlet.

Diagram Description: Figures illustrate the assembly process: Figure 1 shows connecting the bottom section to the base. Figure 2 shows connecting the middle section to the bottom. Figure 3 shows connecting the top section. Figure 4 shows adjusting branches and wires. Figure 5 shows shaping individual branches. Components labeled include Tree top connector, Plug 2, Foot pedal switch, Plug 1, and Tree base.

Troubleshooting

If any lights do not work on your pre-lit tree, please check the following before calling customer service:

• If the entire tree or a section of the tree does not light:
  • Make sure the end connector of the power cord is well connected to the bottom section (C).
  • Check that each section of the tree is well connected.
  • Check that there is power at the electrical outlet.
  • Check fuses in the tree's plugs and replace if necessary (see "Replace the fuse" below).
• If a strand of lights still does not work:
  • Check that all lamps are tightly fitted inside the lampholders and that no lamps are broken or missing. Replace any broken or missing lamps with replacement lamps provided (see "Replace the lamp" below). If all lamps are firmly in the lampholders, slightly twist the lamps from side to side to ensure proper connection.
  • If the lights still do not work, carefully remove each lamp one by one out of the problem light string. Pull the lamp AND plastic base straight out of the lampholder. Do not twist lamps while removing from lampholders. Check the two wires at the bottom of the lampholder. Each wire should be aligned properly on the lampholder to ensure a proper connection in the lampholder. If one wire is missing or too short, please replace the lamp with a replacement lamp (provided).
• If you are still experiencing problems with the tree, please contact customer service at 866-205-9854.

Loose branches

If a branch of the tree falls off, follow the steps below to reinstall it with a spare bolt:

1. Place the branch into the slot of the bracket.
2. Insert a spare bolt (F) through the hole and use diagonal pliers (not included) to crimp the bolt (see Figure A).

Diagram Description: Figure A shows how to reattach a loose branch using a bolt and pliers.

⚠️ CAUTION! ALWAYS UNPLUG YOUR TREE FROM ITS POWER SOURCE BEFORE ATTEMPTING EITHER FUSE OR LAMP REPLACEMENT.

User Servicing Instructions

Replace the fuse:

A) Replace the fuse of the extension cord with foot pedal switch (1 replaceable 5 A, 125 V fuse is located in the plug):

Note: This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.

1. Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.
2. Open the fuse cover. Slide open the fuse access cover on top of the attachment plug towards the blades.
3. Remove the fuse carefully.
4. Risk of fire. Replace fuse only with a 5 Amp, 125 Volt fuse (provided with product).
5. Close the fuse cover. Slide closed the fuse access cover on top of the attachment plug.
6. Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Diagram Description: Illustrations show how to open the fuse cover on the plug.

B) Replace the fuse of the power cord from the bottom section (C) and plug 2:

1. Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.
2. Open the fuse cover. Slide open the fuse access cover on top of the attachment plug towards the blades.
3. Remove the fuse carefully.
4. Risk of fire. Replace fuse only with a 3 Amp, 125 Volt fuse (provided with product).
5. Close the fuse cover. Slide closed the fuse access cover on top of the attachment plug.
6. Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Diagram Description: Illustrations show the fuse rating (3A MAX, 125V) and the fuse access cover.

Replace the lamp:

1. Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.
2. Unlock the burned-out LED lamp by lifting the hook.
3. Pull the lamp and plastic base straight out of the lampholder.
4. Replace the lamp with only a 3.0 Volt, 0.06 Watt, LED type lamp (provided with product). Always match the hook to the tab.
5. Lock the hook of the lamp base by pushing the lock down into the tab.

Diagram Description: Diagrams show the process of unlocking, removing, and locking a new lamp into the lampholder, highlighting the hook and tab mechanism.

CAUTION:

• To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.0 Volt, 0.06 Watt LED lamps only. The LED lamp has polarity. Do not deliberately change the direction of the LED lamp in the lamp holder.
• Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Replace lamps only with the spare lamps provided with this product.

User Servicing Instructions (Continued)

If the new lamp base does not fit in the lampholder, follow the steps below before step 4 of lamp replacement:

• Pull the reflector out.
• Remove the base of the burned-out lamp by straightening lamp leads and gently pull the lamp out.
• Thread leads of the new lamp through holes in the old base, with one lead in each hole.
• After the lamp is fully inserted into the base, bend each lead up, like other lamps in the light set, so that the leads will touch the contacts inside the lampholder (always match the long lead of the new lamp to the hook of the lamp base).
• Insert the reflector into the base.

Diagram Description: Diagrams illustrate the process of preparing the old base and inserting the new lamp leads.

CAUTION

• To reduce the risk of electric shock, use only with the power-supply cord provided or with a cord set intended for indoor use.
• Do not use a cracked, frayed, or damaged cord. Inspect the cord periodically.
• Do not abuse the cord - Do not carry the product by the cord or yank or pull it to disconnect from the outlet.
• Disconnect the product from the outlet when not in use.
• Do not overload. Connect other lighting strings or tree toppers end-to-end up to a maximum of 216 watts (1.8 Amps) total. Do not interconnect low-voltage products.

Use and Care Instructions

• Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
• When storing the product, carefully remove the product from wherever it is placed to avoid any undue strain or stress on the product conductors, connections, and wires.
• When not in use, store neatly in a cool, dry location protected from sunlight.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Statement (Continued)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

UL Model No.: TME7.5-6(0.3)

Storage

Disassembled tree can be stored in its original box. Store tree in a cool, dry place where the temperature does not exceed 100°F (38°C).

Patents and Contact Information

ONE PLUG® U.S. Patents: US8,454,186, US8,454,187, US8,936,379, US9,140,438, US9,157,588, US 9,179,793, US9,243,788, US 10,194,764, US 10,433,604, US 10,578,289, US 10,721,981, US 11,006,687. Other Patents Pending. See www.williscorporation.com/about.html#p6 for a complete list of patents.

Archway Marketing Services
DEPT. 4599, CAROL STREAM, IL 60122-4599
866-205-9854

Dongguan Newone Trading Co., Ltd.
1001 Room, No.273, Jinxiu Road, Changan Town, Dongguan City, Guangdong Prov., China
866-205-9854
williselectric@archway.com

Made in Cambodia. The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product. This product is manufactured by Dongguan Newone Trading Co., Ltd.