MGI Zip Navigator User Manual VERSION 4.7

3.1 Attaching the Rear Wheels

First, lubricate both axles using the black lubricant cloth provided in the MGI Pouch. Lubrication of the axles should be performed regularly to keep your cart in optimal condition. (Refer to 10.5 MGI Service Schedule)

Diagram showing the rear wheel of the MGI Zip Navigator, highlighting the grey release button on the wheel hub and the axle with grooves for positioning.

Press the grey release button on the wheel hub. Place the wheel onto the axle. You will need to match up the inner female groove on the axle and the male of the wheel. When placed in position, simply release the button. You will hear a “click” when the wheel is properly secured.

To check that the wheel is properly in position, pull on the wheel. If it is properly in position, it will not slide off. Repeat for the other wheel.

3.2 Rear Wheels Positions

The MGI Zip Navigator is designed to allow the rear wheels to be in two positions. The position is determined by where the wheel is locked on the axle in either of the two grooves [see picture]. The drive position is used during the normal operation of the Zip Navigator. The free wheel position is used to push the Zip Navigator freely, if required.

Diagram illustrating the two possible positions for the rear wheels on the MGI Zip Navigator axle: 'Drive position' (closest to the battery base) and 'Free wheel position' (closest to the end of the axle).

i. Drive position – Lock the wheel onto the groove closest to the battery base. To do this, press the grey release button on the wheel hub, push the wheel onto the axle as far as possible. To test for drive position, try rolling the wheel backwards. If you feel resistance, then the wheel is now in drive position and ready to use. Repeat for the other wheel.

ii. Free wheel – Lock the wheel into the groove closest to the end of the axle. To do this, press the grey release button on the wheel hub, push the wheel onto the axle and push the release button onto the groove. To test for free wheel position, try rolling the wheel backwards. The wheel should spin freely with no resistance. Repeat for the other wheel.

3.3 Unfolding

Please see below the steps to unfold a Zip Navigator Handle.

1. Ensure both rear wheels are attached.
2. Release fold lever.
3. Move the top bag support away from the front wheel assembly until you hear it click.
4. The handle is now free to pull upwards. The handle will naturally unfold as you continue to pull until the handle is completely open.
5. Ensure that the latch at the bottom of the handle clicks into place.
6. Close the fold lever to lock the handle into place in one of three positions.
7. Push the top bag support down to move it into position.

3.4 Folding

Step 1: Disconnect the battery by lifting the battery handle. It can be left on or removed from the Zip Navigator.

Step 2: Open the fold lever to release the handle.

Step 3: Pull the latch up at the bottom of the handle.

Step 4: Lower the handle until flat.

Step 5: Push the toggle down on the top bag support and then move the top bag support down so that it locks over the front wheel assembly.

Step 6: Close the fold lever to lock the handle into place.

3.5 Fourth Foldable Rear Wheel

The MGI Zip Navigator comes standard with a fourth foldable and extendable rear wheel. This wheel MUST be unfolded and extended into position at all times when the Zip Navigator is in use. This will provide the ultimate stability across all terrains. This fourth wheel should be cleaned regularly with a cloth to ensure it can be folded and retracted as required for storage.

3.6 GPS Holder and Top Handle Compartment

In the top handle compartment, there is a position for a GPS/mobile device holder. Open the compartment and connect the holder into position. To open, press the button at the top of the holder. Place the GPS into the cradle, then close the holder by squeezing the two sides closer together. To remove, gently push the GPS Holder up and away from the Navigator.

3.7 Inverting Rear Wheels

The rear wheels can be inverted on the axle to reduce the size of the Zip Navigator when folded. To invert the rear wheels, press the grey release button on the wheel hub and remove from the axle. Invert the rear wheels so that the wheel hub protrudes away from the axles. Press the grey release button on the wheel hub and release once the wheel is fitted onto the axle.

4.1 Initial Charge

• Before using your MGI Zip Navigator for the first time, you must fully charge the battery overnight.
• Plug the charger AC lead into a power point - the green LED illuminates to indicate the charger is on.
• Plug the charger output connection into the connector on the front of the battery - the red LED illuminates to indicate it is charging.
• When the charging LED indicator has turned green, the battery is fully charged and ready for use.

Image of the MGI 24v Lithium battery and its associated charger, with LED indicators for charging status.

Please refer to the battery charger user manual for further information.

4.2 Connecting the Battery onto the Zip Navigator

Position the battery on the Zip Navigator and push the battery down to secure it.

Three-part image sequence illustrating how to connect the MGI 24v Lithium battery to the Zip Navigator by positioning it and pushing the handle down.

Push the handle down to connect the battery to the Zip Navigator.

Your Zip Navigator has been equipped with a fail-safe battery connection, so the Zip Navigator will not move when you connect the battery. Your Zip Navigator will only start via the top handle button or the remote.

4.3 Charging the Battery after use

• Disconnect the battery by lifting the handle.
• The battery can be left on or removed from the Zip Navigator for charging.
• Plug the charger AC lead into a power outlet - the green LED illuminates to indicate the charger is on.
• Plug the charger output connection into the connector on the front of the battery - the red LED illuminates to indicate charging.
• When the charging LED indicator has turned green, the battery is fully charged and ready for use.

*The Zip Navigator AT battery MUST be charged after every use. Failure to do so may damage the battery.

4.4 Battery Storage

• Lithium batteries should not be stored for long periods of time, either depleted or fully charged. Ideally, the battery should be at 40-50% capacity, stored in a clean, dry environment on a hard, non-flammable surface, between 15°C (60°F) to 25°C (80°F). As lithium batteries slowly discharge over time, it is recommended that the battery be power cycled every 6 months if left unused and stored as above.
• Do not leave your lithium battery in a car, as high temperatures can damage the battery cells. Do NOT charge your MGI lithium battery for more than 10 hours.

4.5 Disposal of Lithium Batteries

This product contains materials that require special handling at end-of-life. Please contact your local environmental authority or governing body for guidance on safe disposal and recycling in accordance with regional regulations. DO NOT dispose of in general waste.

Symbol indicating correct disposal of the product according to EU regulations, advising against disposal with household waste and promoting recycling.

Correct Disposal of this product: This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

6.1 Top Box Display

The Top Box Display includes the following indicators:

1. Distance Mode Button
2. Unit Setting Button
3. ON / OFF Speed Control Button
4. Speed Setting Indicator
5. Main Battery Level Indicator
6. Distance Mode
7. Distance
8. Unit Measurement
9. Remote Battery Level Indicator

Diagram of the MGI Zip Navigator's top box display, with numbered callouts identifying various indicators and buttons.

6.2 Start / Stop the Zip Navigator

Zip Navigator Speed Control

Please note the following points regarding the Zip Navigator Speed Control:

1. To select the desired speed, rotate the speed control button. Turning the speed control button clockwise will increase the speed, whilst anti-clockwise will decrease speed.
2. The speed setting chosen is displayed in the centre of the screen.

Please note you will feel notches as you rotate the speed control. The notches do not indicate a change in speed. The speed will only increase or decrease as the number changes in the display.

3. To start the Zip Navigator at this desired speed, press the speed control button.
4. Another tap will stop the Zip Navigator.
5. The desired speed can be altered up or down while the Zip Navigator is moving.

Image of the MGI Zip Navigator's speed control dial on the top box.

6.3 Turn the Zip Navigator Off

Zip Navigator Battery

Please note the following points regarding the Zip Navigator battery:

Connecting the Battery onto the Zip Navigator

1. Position the battery on the Zip Navigator and push the battery down to secure it. Push the battery handle down to connect the battery to the Zip Navigator.
2. To turn the Zip Navigator Top Box Display off: Hold down the Start/Stop Speed Control Button and Left Hand Distance Mode Button for four seconds, and the display will turn off, thereby disabling the Top Box.

Please note that the battery will still be connected to the Zip Navigator and will continue to draw power whilst connected.

Please note that the Zip Navigator display will also turn off if the Speed Control is not operated for 30 minutes.

Once again, please note that the battery will still be connected to the Zip Navigator and will continue to drain whilst connected.

3. To reactivate the Top Box Display, whilst the battery is connected, hold down the Start/Stop Speed Control Button and Left Hand Distance Mode Button for four seconds, and the display will turn on, thereby enabling the Top Box.
4. To fully shut down the Zip Navigator and prevent the battery from discharging, disconnect the battery by lifting its handle. The battery can be left on or removed from the Zip Navigator.

6.4 Main Battery Level Indicator

Battery indication is located on the left side of the top box screen. Four coloured bars are highlighted showing full charge. The number of bars displayed indicates the battery life available. You should always check the battery status before you play golf to ensure the main battery is fully charged.

6.5 Unit Measurements

You can change from meters / kilometres / yards / miles simply by pressing the Unit Setting Button [on the right].

6.6 Distance Modes

There are three distance measurement modes. To move between the modes, press the Distance Mode Button [DM] on the left.

Distance A and B: Resettable distance measurements can be used to measure how far you hit your shot and to measure how far you have walked for the day. To reset, simply press the DM Button [left side] for 3 seconds until the reading displays “0”.

Distance Total: Cannot be reset as it is the odometer for the life of the Zip Navigator. This feature will assist with service reminders, which is recommended every 500km (310 miles) or 6-month period.

6.7 Competition Mode

In the unlikely event that the club you are playing at does not allow the use of distance devices, you will need to disable the distances feature on the MGI Zip Navigator.

To disable the distance recording feature, simply hold down the left and right buttons at the same time for 3 seconds and “COMP MODE” will appear on the screen. In addition, the distance recording will be removed from the screen.

To exit COMP MODE, hold down the left and right buttons at the same time.

Image of the MGI Zip Navigator's display showing 'COMP MODE' and a speed indicator, indicating the competition mode is active.

7.1 Charging Your Remote Control

Before you start using your Zip Navigator, you must fully charge the remote control battery for approximately 6 hours or overnight using the USB cord provided. The top left UNLOCK button will flash while charging. When a full charge is complete, the green light will stay on and stop flashing.

To charge the remote, plug the other end of your cable into the Zip Navigator USB port located underneath the handle. Alternatively, the remote can be charged via PC, Laptop, or AC adaptor (not included).

To check the level of power in the remote, press any button to signal the digital top box, and the remote control battery level will show on the screen of the Zip Navigator.

We recommend recharging your remote battery when recharging your main battery after each round.

7.2 Forward Arrow

Press the forward button to start and accelerate the Zip Navigator. The longer you press the button, the faster the Zip Navigator travels. The Zip Navigator will always start at speed 4 when using the remote.

7.3 Down Arrow

The down arrow decreases the speed and initiates reverse. If you are moving forward, the down arrow can be used to decrease speed; the longer the pressure, the slower the speed. If you hold down the button, the Zip Navigator will reverse. If you release the down arrow whilst the Zip Navigator is in Reverse Mode, the Zip Navigator will stop [safety feature].

7.4 Left and Right Arrow

When the Zip Navigator is stopped, press the appropriate turn command and keep depressed until the degree of turn is achieved, then press the forward button for the Zip Navigator to go forward.

Whilst the Zip Navigator is moving, press the appropriate turn command and keep depressed until the degree of turn is achieved. Momentary pressure will make a small adjustment to the direction, whilst prolonged pressure will increase the degree of turn and speed of the turn.

7.5 Speed Control – Manually and Remotely

Under manual control, you can adjust the speed by turning the speed control button clockwise [increase speed] or anti-clockwise [decrease speed]. When changing to the remote control, irrespective of the speed level indicated on the display, the Zip Navigator will always start at speed 2.

7.6 Keypad Unlock and Lock

The remote control has two buttons at the top which allow you to LOCK and UNLOCK the keypad. This will eliminate accidental button input when the remote is kept in your pocket. The STOP button will continue to work when the LOCK feature is activated.

Image of the MGI Zip Navigator remote control keypad, showing the directional arrows, speed control, STOP, LOCK, and UNLOCK buttons.

7.7 Remote Range and Safety Stop

The Zip Navigator can be remotely controlled up to a range of 100m - 200m. The remote's range is affected by many factors, such as the environment, weather, geomagnetic, and external electromagnetic interference. If the remote control loses contact with the Zip Navigator, then the automatic Safety Stop will initiate after five seconds. If the Zip Navigator is activated using the manual controls, the automatic Safety Stop feature will not be active. It is the user's responsibility to ensure that they have control of the Zip Navigator at all times. If the Navigator is inadvertently activated, it is the user's responsibility to ensure that it does not go into hazards, irrespective of the Remote Range and Safety Feature.

Please note, the top left unlock button will flash every 3 seconds while the Safety Stop feature is active.

7.8 Pairing a Remote

In the unlikely event that your remote loses pairing with your Zip Navigator, or you have replaced your remote, it will need to be paired as follows:

1. Lift the main battery handle, disengaging the battery terminals.
2. Hold down the STOP Button on the remote until both the LOCK and UNLOCK buttons illuminate and remain solid, then release the STOP Button.
3. Re-engage the main battery by pushing the handle back down, ensuring the lights on the remote remain illuminated.
4. The remote will synchronise with the Top Box – the process will be complete once the LOCK and UNLOCK buttons are no longer illuminated.

Please note, if you do not connect the Zip Navigator, as per point 3, with a battery, the remote will exit pairing after one minute.

9.1 Warranty Policy

The MGI Zip Navigator is covered by a limited 3-year manufacturer's warranty from the date of purchase. Duration of this warranty is:

• 3 years on parts*
• 3 years on Lithium batteries and chargers

*MGI or an authorised service centre will repair or replace any parts found to be defective in materials or workmanship under normal use, provided that:

1. The MGI Zip Navigator has been properly used, maintained, and regularly serviced [see section 10.5].
2. The replacement or repair is performed by an authorised MGI service centre or the owner with MGI approval.

Our goods come with guarantees that cannot be excluded under Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty is in addition to other rights and remedies available to the consumer under law.

If a warranty claim is to be made, please cease use of the goods immediately and contact your place-of-purchase or your nearest Authorised Service Centre. Alternatively, MGI can be contacted directly via details on the back of this User Manual. Proof-of-purchase is required.

9.2 Warranty Exclusions

The following events are not covered under warranty:

• Normal wear and tear; (e.g. tyres, rubber handlebar, elastic straps, paintwork, battery performance, axles threads, charging ports on batteries and remotes, screen glass etc.)
• Minor appearance defects which bear no effect on the operation of the unit and are considered by the manufacturer to be within the accepted standards.

The following events will void warranty:

• Battery BMS failure caused by improper charging cycles, i.e. letting battery drain to zero charge.
• Any alteration performed by non-authorised people or companies.
• Fitting of parts or accessories not recommended by MGI.
• Any damage caused by continued operation of the product after it is known to be defective.
• Damage to the seat and/or seat support bracket on the unit.
• Damage caused by partial or full submersion in water - affecting the drive system or electronics.*
• Damage caused by the unit being driven into bunkers, other course hazards, or clubhouse and carpark hazards.
• Damage caused by golf balls or golf clubs.
• Application of external force to any part of the unit or battery.
• Fusion/overheating of motor or electronics through overload (i.e. using the product to aid the user uphill) or continued operation whilst stationary.
• All implied warranties [save those preserved by statute] are excluded.
• Liability for consequential damages under any and all warranties are excluded to the extent exclusion is permitted by law.

*In the event of submersion in water (partial or full) of your Zip Navigator, MGI advises the complete write-off of your Zip Navigator. The cost of replacing the water-damaged components (including labour) exceeds the price of a replacement Zip Navigator.

If you elect to purchase replacement components, i.e. motors, gearbox, motor controller, and electronics, we advise the replacement of ALL components simultaneously. Replacing individual components on a water-damaged Zip Navigator poses a higher risk of future failure of other components and therefore these parts will not be covered under warranty.

Please note that MGI does not warrant water-damaged batteries and, due to fire risk, under no circumstances should they continue to be used.

MGI Golf only offers a warranty within the country where the buggy/caddy was purchased - across all MGI electric buggies/caddies, batteries, chargers, and accessories. In some instances, MGI may uphold a warranty claim and supply the parts under warranty; however, the freight and labour to install/repair must be covered by the customer.

9.3 Parts Installed During Warranty

Warranty coverage for components installed during a motorised Zip Navigator's warranty period shall consist of the duration of the Zip Navigator's warranty period, provided the warranty installation is performed by MGI, an authorised service centre, or the Zip Navigator owner on approval. Replacement of parts under warranty will not extend the warranty of the Zip Navigator or parts.

Warranties are non-transferable. The warranty applied to a product, on purchase, is limited to the original purchaser.

10.1 Cleaning Your Zip Navigator [See Maintenance Schedule]

For years of good operation, your Zip Navigator requires care and attention:

• Keep your Zip Navigator clean by using a cloth with warm water and a mild detergent.
• Do not hose down your Zip Navigator under any circumstance, as the Zip Navigator has electronic components.
• Ensure that the seat stem bracket is free of sand and debris.
• Do not submerge your Zip Navigator, partially or fully, as it will damage the drive system and/or the electronics. The Zip Navigator is designed to withstand wet weather (in conjunction with a Zip Rain Cover [sold separately]).
• Clean the Zip Navigator battery base when the battery is removed from the Zip Navigator.
• Regularly brush away sand/dirt from moving parts and toggles for smooth operation.

10.2 Rear Wheel Axles Maintenance [See Maintenance Schedule]

The rear wheel stub axles need to be lubricated regularly. Remove the rear wheels by depressing the spring clip and at the same time pull off the wheel. Apply Petroleum Jelly or light grease to the stub axles. Use a very small amount, as the lubricant can attract sand. If you play in sandy conditions, you should clean the axle and re-lubricate fortnightly. Once your cloth has dried out, please lightly coat the axle with Petroleum Jelly.

10.3 Upper and Lower Bag Strap Maintenance [See Maintenance Schedule]

The bag straps should be replaced as per the Service Schedule. The upper bag strap can be replaced by:

• Removing the left and right hand straps from the upper bag support.
• Undo and remove the screws holding the strap in position on the bag support.
• Remove and replace both bag straps.
• Insert bag strap securing screws.

10.4 Correcting the Alignment

Please see Zip Navigator Motor Trimming at mgigolf.com.

10.5 MGI Service Schedule

It is the owner's responsibility to ensure that all periodical checks, necessary adjustments, and services are carried out. If in doubt, please contact the MGI service centre:

• Australia: 1300 644 523
• USA: 1800 617 2990

Any work performed on your Zip Navigator should be recorded on your service record (see page 21) regardless of the work.

BO = Zip Navigator owner can carry out this work
SC = Charged work to be carried out by approved service centre
BO/SC = The six-monthly service can be completed by either an authorised service centre or the owner of the Zip Navigator.

10.6 Service Record