VEVOR

Technical Support and E-Warranty Certificate

For support, visit: www.vevor.com/support

Disclaimer: Pricing expressions like "Save Half" or "Half Price" represent estimated savings compared to major brands and may not apply to all product categories. Please verify savings carefully when ordering.

Product Image

[Description: A black, industrial-style pressure paint pot with a capacity of 10 liters, mounted on a wheeled base. It features a lid with multiple valves, regulators, and connectors for air intake and paint output. An agitator assembly is visible on top.]

Need Help? Contact Us!

For product questions or technical support, please feel free to contact VEVOR.

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret this user manual. The appearance of the product is subject to the item received. VEVOR will not provide separate notification for technology or software updates.

SAFETY INSTRUCTION AND PRECAUTIONS

⚠️ WARNING: Read this material before using this product. Failure to do so can result in serious injury.

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or under the influence of alcohol, drugs, or medication.
6. Product capabilities apply to properly and completely assembled product only.
7. Assemble on a flat, level, hard, and smooth surface capable of safely supporting a fully loaded Pressure Paint Pot.

⚠️ WARNING:

1. This product is not a toy. Do not allow children to play with or near this item. Children or persons with physical disabilities, and those unfamiliar with safe operation, are prohibited from using this product.
2. This 10L product allows paint to be pressurized to 70 PSI; the maximum operating pressure must not exceed 80 PSI to avoid personal safety risks.
3. The safety valve on the pressure barrel protects normal pressure. It is factory set within the allowable range and should not be removed or adjusted at will during normal use.
4. This product should not be modified, nor should dangerous operations such as drilling or welding be performed, as these may produce a tempering effect, damage the pressure barrel, and affect the product's service life.
5. It is strictly forbidden to pour strong acidic or alkaline liquids into this product to avoid corrosion of the tank body and causing personal injury.
6. Use as intended only.
7. Inspect before every use; do not use if parts are loose or damaged.
8. After spraying, the product must be thoroughly cleaned to extend its service life.

Preface

This paint barrel is composed of an air pressure regulating valve, safety valve, vent valve, discharge port, and four movable wheels. All parts are made of the best materials, have passed strict quality control, and feature a durable baking paint finish.

Product Decomposition

[Description: Schematic diagram of the JY-ZDS30L decomposition. This diagram shows an exploded view of the pressure paint pot. Key components include the main pressure barrel body (1), inner barrel (2), barrel lid (8), air motor (15) with motor mounts (17) and trachea (16), pneumatic regulating valves (21), regulators (26), pressure gauge (28), discharge valve (24), outlet valve (12), air intake valves (25), and four movable wheels (39). Various nuts, bolts, gaskets, and connectors are also depicted.]

Parts List

List of User Thread Specifications

How to Use

1. Before use, ensure there is no residual pressure in the pressure barrel. If residual pressure exists, pull the Red Hat safety valve bleed ring on the lid to completely release the air pressure inside the barrel for safety.
2. Loosen the wing nuts and open the lid.
3. Close all valves. Connect the sprayer to the paint discharge port (24) and ensure the outlet valve (12) is closed. [Note: Original text was ambiguous, interpreted based on typical usage.]
4. Connect the air intake connector (20) and open the air intake valve (25). [Description: Close-up view of the air intake connector and valve.]
5. Adjust the inlet pressure regulator: rotate clockwise to increase working pressure, and counterclockwise to decrease pressure in the barrel. [Description: Close-up view of the air pressure regulator and a pressure gauge showing approximately 30 PSI.]
6. Open the outlet valve (12) and the discharge valve (24).
7. If the paint settles, turn on the air motor to stir. [Description: Close-up view of the pressure paint pot lid with the air motor assembly, indicating stirring action.]

Maintenance

1. After use, cut off the air source. Open the balloon valve switch on the lid to release all air from the barrel. Loosen the butterfly bolts, open the lid, pour out residual paint, and clean all parts touched by paint with an appropriate solvent.
2. Pour cleaning solvent into the bucket, close the lid to lock it, open the intake valve, and operate the sprayer until clean solvent appears.
3. Safety valves must be kept clean at all times.

Air Leakage Remedy

Note: If you find air leakage during use, apply glue evenly along the leak area. Close the lid of the barrel, tighten the screws while the pressure reaches 15 PSI (hold for about 10 seconds) to allow the glue to penetrate the leakage. Close the intake valve, open the pressure relief plunger, and let it stand for 6-8 hours until the glue is completely solidified before continuing use.

Troubleshooting

[Description: Diagram illustrating the correct diagonal sequence for locking the bucket lid. Numbered points (1, 2, 3, 4) are shown on the lid, with arrows indicating the order of tightening: first 1-2, then 3-4.]

Contact and Distribution Information

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Made In China

UK REP: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

EC REP: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX