User Guide for kogan models including: 2.1 Wireless Soundbar with Bluetooth, KASBRT21A
2.1 Wireless Soundbar with Bluetooth KASBRBT21A Quick Start Guide Product Specifications Power Supply AC 100-240V / 50-60Hz Total Power Consumption 80W Input Sensitivity (Subwoofer) 300mV -/ 20mV Input Sensitivity (Satellite) 800mV -/ 50mV Speaker impedance of Satellite 4 Ohm S/N (A Weight) 8 Ohm THD (1kHz, 1W) 0.5% Frequency Response 45Hz ~ 20KhzdB L/R Separation (1kHz) 30dB
Power Supply Total Power Consumption Input Sensitivity (Subwoofer) Input Sensitivity (Satellite) Speaker impedance of Satellite S/N (A Weight) THD (1kHz, 1W) Frequency...
Power Supply. AC 100-240V / 50-60Hz. Total Power Consumption. 80W. Input Sensitivity (Subwoofer). 300mV -/ 20mV. Input Sensitivity (Satellite). 800mV -/ ...
File Info : application/pdf, 5 Pages, 1.25MB
DocumentDocument2.1W irelessSoundbarwithBluetooth KASBRBT21A QuickStartGuide Product Specifications PowerSupply TotalPowerConsumption InputSensitivity(Subwoofer) Input Sensitivity (Satellite) SpeakerimpedanceofSatellite S/N (A W eight) THD(1kHz,1W ) Frequency Response L/R Separation (1kHz) L/R Balance (Stereo) BluetoothTransmissionDistance 2.4G Betweenwirelesssubwoofertransmissiondistance AC 100-240V / 50-60Hz 80W 300mV -/+ 20mV 800mV -/+ 50mV 4 Ohm 8 Ohm 0.5% 45Hz ~ 20KhzdB 30dB +/- 2dB CSR 2.1m 5 metres Controls and Functions Front Panel Rear Panel Attention Pleasehandlethisproductwithcareandinspectitregularlyto ensureitisingoodworkingorder. Iftheproduct,powersupplycordorplugshowsanysignsof damage:stopuse,unplugandcontactKogan.com support. Safety Precautions All safety and operational instructions should be read before the unit is used. A copy of these instructions should be kept for future reference. · Power & Power Cord: connect the device to the power type as advised. Do not place objects on top of the power cord. · Water & Moisture: the device should not be used near water (for example, near a bathtub, sink, laundry, near a swimming pool etc..) · Ventilation: The device should be situated so that its location or position does not interfere with its proper ventilation. Do not use the device on a bed, sofa, rug or similar surface that may block the ventilation openings. · Heat: Keep the device away from heat sources such as radiators, heaters, stoves or other appliances that generate heat. · Damage requiring service: The appliance should be serviced by the Kogan customer support technicians when: 1) The power-supply cord or the plug has been damaged; or 2) Objects or liquids have fallen into the device; or 3) The device has been exposed to rain; or 4) The device is not operating normally or exhibits a marked change in performance; or 5) The device has been dropped or damaged. · Clean only with a dry cloth. · Unplug the device during lightning storms or when it will remain unused for extended periods of time. RemoteControl 1 Standby (On/Off) 2 Normal Mode 3 Reset (location retrieval button) 4 Bluetooth track Prev 5 Volume down 6 Bass down 7 Music mode 8 Input 9 Bluetooth track next 10 Mute mode 11 Movie mode 12 EQ adjust sound effect 13 Short press: Bluetooth Play/Pause Long press: Blueooth Pair/Disconnect 14 Volume op 15 Bass up Remotecontrolbatteryreplacement 1. Replace the remote control battery when the range is reduced considerably. 2. Use only Cr2025 or D12032 3V lithium batteries. 3. Bear in mind that lighting and other room conditions, in addition to battery age, can affect the operating range of an infrared remote control. PairingtheSoundbar&Subwoofer To use the wireless subwoofer, you must ensure that the soundbar itself has been powered up and is ready for pairing. To do this, simply turn the soundbar on, then switch the subwoofer on 30 seconds later. If you turn the subwoofer on before the soundbar has booted up, the units will not pair and you will not get any sound from the subwoofer. The failure to pair will be indicated by the small blue LED light in the rear of the subwoofer flashing. If the units fail to pair correctly, turn the subwoofer off, wait for 10 seconds, then switch it back on again. System ConnectionInstructions Basic Status Connected AUX single, Optical and Coaxial signal on the rear panel of the Sound Bar. The LED display will display "- -" to show it is in standby mode. LED DigitStatusandFunction LED DIGIT AU OP CO BL Number FUNCTION AUX audio signal input Optical audio signal input Coaxial signal input Bluetooth audio signal input Volume label LED DIGIT EQ E1 E2 E3 FUNCTION Adjust Equaliser mode Normal sound effect Music sound effect Movie sound effect EQ Setting Treble setting: press the EQ button on the remote control, then press the VOL+ button and the VOL- button to adjust the treble, with the range increasing or decreasing by 7db. (Reset: Press EQ, then press the reset button).