Installation Guide for PHANTEKS models including: PH-GB4090AS-BK01 Glacier G40 Asus GPU Block, PH-GB4090AS-BK01, Glacier G40 Asus GPU Block, G40 Asus GPU Block, GPU Block, Block
8 nov 2022 — WARNING - This product is intended for advanced users. Improper installation may result in damage to your equipment. While all e orts have.
GLACIER G40 ASUS GPU BLOCK PH-GB4090AS_BK01/CR01/MW01_BP INSTALLATION GUIDE V1.0 PACKAGE CONTENTS GB4090AS block QTY: 1 GLACIER stop fitting QTY: 2 Support bracket QTY: 1 Thermal compound QTY: 1 2 3 6 6 6 6 6 6 5 5 5 5 1 1 4 4 7 88 7 88 Block thermal pads QTY: 2 pre-cut pieces M3x10 screws QTY: 1 M2.5x5 screws/washers QTY: 4/4 Phanteks D-RGB cable QTY: 1 1 2 5 3 3 4 6 6 GB4090AS backplate QTY: 1 Backplate thermal pads QTY: 2 pre-cut pieces 8x M2.5x8 flush screws 2x M2.5x6 flush screws Motherboard cable QTY: 1 WARNING - This product is intended for advanced users. Improper installation may result in damage to your equipment. While all efforts have been made to provide the most comprehensive information possible, Phanteks assumes no liability expressed or implied for any damage(s) occurring to your components as a result of using Phanteks cooling products, either due to mistake or omission on our part in the below instructions, or due to failure or defect in the Phanteks cooling products. Do not disassemble the water block. Warranty will be voided. STEP 1. REMOVING STOCK COOLER Unscrew all highlighted screws to remove the stock cooler and backplate. backplate screws stock cooler screws Make sure to unplug the LED and Fan cables when you remove the stock cooler. ASUS ROG STRIX RTX 4090/4080 ASUS TUF GAMING RTX 4090/4080 Keep for step 3 STEP 2. APPLYING THERMAL PASTE & PADS Clean off the original thermal compound. We recommend using isopropanol alcohol. Remove the protective film and place the the thermal pads on the correct position on the PCB. Apply the Phanteks Thermal Compound to the center of the GPU chip. ASUS ROG STRIX / TUF RTX 4090/4080 6 6 86 85 5 2 74 1 1 47 58 6 3 85 6 6 Make sure to remove the protective film on both sides of the thermal pads. 2 3 6 6 6 6 6 6 5 5 5 5 1 1 4 4 7 88 7 88 STEP 3. MOUNT THE WATER BLOCK Secure the support bracket to the GPU block first. Carefully position the water block onto the graphics card. Align the mounting holes on the PCB with the holes on the water block. Secure the water block with 4 M2.5x5mm screws and washers to the PCB. Secure the Support Bracket with the original cooler screw. Make sure to lay the GPU with the water block flat down without resting on the PCI bracket. 1x 4x 4x STEP 4. APPLYING THERMAL PADS Remove the protective film on both sides and place the thermal pads on the correct position on the backplate. 1 2 5 3 3 4 6 6 STEP 5. INSTALL THE BACKPLATE Carefully position the backplate onto the graphics card. Align the mounting holes on the PCB with the holes on the backplate. Secure the backplate with 8x M2.5x8mm and 2x M2.5x6mm flush screws to the PCB. 6 43 2 35 6 1 8x 2x Secure with original screw. STEP 6. INSTALL INTO THE SYSTEM 1. Connect the D-RGB cable to the D-RGB strip in the water block. All Phanteks D-RGB products can be daisy-chained together. 2. Install the GPU into the system. 3. Install the waterloop and Stop Fittings Opotional: Always perform a leak test before providing power to any system components. Use the Motherboard cable to connect the LED strip to the motherboard. Connect to Phanteks Case / Motherboard CableAdobe PDF library 16.07 Adobe Illustrator 26.4 (Windows)