Instruction Manual for MODERN FORMS models including: WS-56124 561 LED Wall Scone, WS-56124, 561 LED Wall Scone, LED Wall Scone, Wall Scone, Scone
File Info : application/pdf, 6 Pages, 1.06MB
DocumentDocumentINSTALLATION INSTRUCTION WS-56124/WS-56137 · Read all instructions before installing. · System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations. · When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only. · Retain installation instructions for future maintenance reference. All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing. Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth. · Lisez toutes les instructions avant l'installation. · Le système doit être installé par un électricien licensié conformément au code national de l'électricité (NEC), et également aux règlements locaux. · Lors de la manipulation du luminaire, n'appuyez pas sur les LED. Tenez-le uniquement par la base. Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l'annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées. Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un chiffon humide. A B C D Wire Connector Qty:3pcs+1Extra Mounting Screw Mounting Ring Qty: 1 Extra Qty:1pc Conversion Plate Qty:1pc Modern Forms.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 ModernForms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2020 1 INSTALLATION INSTRUCTION WS-56124/WS-56137 B Mounting Screw Switch Box Ground Wire switch Driver A Wire Connector Mounting back plate Junction Box Screw Fixture Back Plate Dimensions WS-56124: 6 1/4" WS-56137: 7 7/8" 1 3/5" 1 3/8" 2 1/4" Mounting Ring Dimensions 1 3/8" 1 3/4" Ø4" GND Conversion Plate Dimensions WS-56124: 6 3/4" WS-56137: 8 1/4" 1 3/8" 1 3/5" 4 1/2" 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar. 2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation. 3. Loosen the mounting screw (B) from the fixture, and remove the mounting back plate. 4. The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in the canopy (Fig. 4). 5. Secure the mounting back plate to the switch box using junction box screws . (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue; (ii) The side of the mounting plate marked "GND" must face out 6. Connect the driver input wires to switch box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture's ground wire to it. Otherwise, connect the fixture's ground wire directly to the mounting back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box. Secure the fixture to the mounting back plate using the mounting screw (B). Modern Forms.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 ModernForms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2020 2 INSTALLATION INSTRUCTION WS-56124/WS-56137 Junction box Junction Box Screw Junction Box Screw C Mouting Ring D Conversion Plate B Mounting Screw Mounting back plate 3. Loosen the mounting screw (B) from the fixture, and remove the mounting back plate. 4. The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch in the canopy (Fig. 4). 5. Secure the mounting ring (C) to the junction box using junction box screws . (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue; (ii) The side of the mounting ring marked "GND" must face out 6. Secure the mounting back plate and conversion plate (D) to the mounting ring (C) with the junction box screws . 7. Connect the driver input wires to junction box wires as shown in Fig. 3, making sure that all wire connectors (A) are secured. If your outlet box has a green and bare copper ground wire, connect the fixture's ground wire to it. Otherwise, connect the fixture's ground wire directly to mounting ring using the green screw provided. After wires are connected, tuck them carefully inside the junction box. 8. Secure the fixture to the mounting back plate using the mounting screw (B). Fixture Wires Black or Smooth Fixture Wires White or Ribbed Fixture Wires Bare wire (Ground) House Wires Black (Hot) House Wires White (Neutral) House Wires Green or Bare Copper (Ground) 3500K 3000K 2700K Modern Forms.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 ModernForms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2020 3 INSTALLATION INSTRUCTION Trimless Junction Box Cover MKCP-3040-WT CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING. - Read all instructions before installing. - System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations. - When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only. - Retain installation instructions for future maintenance reference. WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing. MISE EN GARDE: POUR ÉVITER TOUT CHOC ÉLECTRIQUE, ASSUREZ-VOUS QUE LE DISJONCTEUR SOIT MIS HORS TENSION AVANT DE COMMENCER. - Lisez toutes les instructions avant l'installation. - Le système doit être installé par un électricien licensié conformément au code national de l'électricité (NEC), et également aux règlements locaux. - Lors de la manipulation du luminaire, n'appuyez pas sur les LED. Tenez-le uniquement par la base. ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l'annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées. COMPONENT OVERVIEW The trimless junction box cover is intended for installation to NEC approved 4" square junction boxes recessed in drywall and flush with the support structure. It may be covered with spackle and/or plaster to conceal junction box visibility. It is to be connected to compatible Modern Forms fixtures. Refer to specifications sheets for more information. OVERALL COMPONENT DIMENSIONS HARDWARE A B C #8 Wire Connector 1/8"-40 x 13/16" Long #8-32 x 3/4" Long TYP Qty: 3 (+1 Extra) Mounting Screw Junction Box Screw Qty: 2 (+1 Extra) Qty: 2 (+1 Extra) 2" D E F NOTE: This accessory is supplied with an optional mounting C-ring for fixture connection via 7/8" K.O. hole. This component may be omitted from the installation if mounting fixtures using #8 screw holes. 1/2" Plastic Spacer Qty: 2 3/4" Plastic Spacer Qty: 2 1" Plastic Spacer Qty: 2 modernforms.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2023 (G0) 1 INSTALLATION INSTRUCTION Trimless Junction Box Cover MKCP-3040-WT TRIMLESS JUNCTION BOX COVER INSTALLATION: The trimless junction box cover is compatible with NEC approved 4" square junction boxes recessed in drywall and flush with the support structure. 1. Install compatible junction box (by others) to the framing structure. Ensure the junction box is flush with the base or front of framing structure (See FIG. 1). 2. Install the mounting plate to the junction box (See FIG. 2). Ensure the spacer alignment base is facing outward. FIG. 2 FIG. 1 FIG. 3 Spacer Alignment Base Junction Box C Screws Ground Wire 3. Determine the drywall thickness and select the appropriate spacer to install between the mounting plate and the trimless junction box cover (See FIG. 3). NOTE: Only 1 matching pair of spacers are to be used per installation. 4. Using the mounting screws provided, attach the trimless junction box cover to the mounting plate (See FIG. 4). 5. Make a 41/8" square cutout in drywall at the intended trimless junction box cover location and proceed to install to framing structure (See FIG. 5). Apply and finish spackle up to the center hole of trimless junction box cover. Ensure #8 holes on the cover are free of spackle. (See FIG. 6). FIG. 5 105mm 105mm FIG. 4 FIG. 6 Mounting Plate Plastic Spacers Spacer Height No Spacer Drywall Thickness 1/2" D 1/2" 5/8" E 3/4" 1" F 1" 11/4" Trimless Junction Box Cover Cover Mounting Screws B Example: 1/2" Drywall (No Spacer) 1/2" 5/8" modernforms.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2023 (G0) 2 INSTALLATION INSTRUCTION Trimless Junction Box Cover MKCP-3040-WT FIXTURE INSTALLATION TO JUNCTION BOX COVER: The trimless junction box cover features two #8 holes which may be used to mount fixtures: 1. Make appropriate splice connections. Wiring may be placed inside the fixture or pushed into the junction box. 2. Using #8 mounting screws supplied with the lighting fixture, attach the fixtures to the #8 holes on the trimless junction box cover. Apply fixture cover or lensing (where applicable) to complete the installation. (See FIG. 7). FIG. 7 A Wire Connector Fixture #8 Mounting Screws modernforms.com Phone (800) 526.2588 Fax (800) 526.2585 Headquarters/Eastern Distribution Center 44 Harbor Park Drive Port Washington, NY 11050 Central Distribution Center 1600 Distribution Ct Lithia Springs, GA 30122 Western Distribution Center 1750 Archibald Avenue Ontario, CA 91760 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2023 (G0) 3