Axxess Integrate - Comprehensive Interface Products for Vehicle UpgradesAxxess Integrate - Comprehensive Interface Products for Vehicle Upgrades
Instructions for AXXESS models including: AXTC-HN1, AXTC-HN1 Honda SWC Steering Wheel Control and Data Interface, AXTC-HN1, Honda SWC Steering Wheel Control and Data Interface, Honda SWC and Data Interface, Honda SWC, Honda Data Interface, Steering Wheel Control and Data Interface
Axxess AXTC-HN1 Wiring Interface Connect a new stereo and retain steering wheel controls and factory backup camera in select 2016-21 Honda vehicles at Crutchfield
File Info : application/pdf, 4 Pages, 648.70KB
DocumentDocumentAXTC-HN1
INSTALLATION INSTRUCTIONS
APPLICATIONS
Honda Civic (Coupe, Sedan) LX, LX-P.........................................................2016-2021 Civic (Hatchback) LX, Sport.............................................................2017-2021 Fit ....................................................................................................2018-2020
Honda SWC (Steering Wheel Control)
and Data Interface 2016-2021
Visit AxxessInterfaces.com for more detailed information about the product and up-todate vehicle specific applications.
INTERFACE FEATURES
· Provides illumination, parking brake, reverse, and speed sense outputs
· Retains the factory backup camera, and also includes an 12-volt to 6-volt step-down converter (AXCSD-6V)
· Retains audio controls on the steering wheel
· Designed to be compatible with all major radio brands
· Auto detects vehicle type, radio connection, and preset controls
· Ability to dual assign steering wheel control buttons
· Retains memory settings even after battery disconnection or interface removal (non volatile memory)
· Micro-B USB updatable
Product Info
TABLE OF CONTENTS
Connections............................................................2 Programming......................................................... 3 Troubleshooting.....................................................4
INTERFACE COMPONENTS · AXTC-HN1 interface · AXTC-HN1 harness · 3.5mm adapter · AXCSD-6V
TOOLS & INSTALLATION ACCESSORIES REQUIRED · Crimping tool and connectors, or solder gun, solder, and heat shrink · Tape · Wire cutter · Zip ties
ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product. NOTE: Refer also to the instructions included with the aftermarket accessory before installing this device.
AxxessInterfaces.com
© COPYRIGHT 2024 METRA ELECTRONICS CORPORATION
REV. 6/6/24 INSTAXTC-HN1
CONNECTIONS
Reset Button
AXTC-HN1
LED
NOTE: If the vehicle's Steering Wheel Controls do not function after the AXTC-HN1 has completed its programing sequence, unplug connector E1 from connector E and connect E2 to E. Once completed, hit the reset button on the interface to restart the programming sequence and test. Refer to LED Feedback Chart for programming information if needed.
3.5mm Adapter (for vehicles without Steering wheel controls or aftermarket radios with a wire for SWC)
Boss (with SWC wire): Key 1 (Gray) - Brown Kenwood / JVC (with SWC wire): Blue/Yellow - Brown
XITE: SWC-2 - Brown
{ Universal Key-A or SWC-1 - Brown
Radio* Key-B or SWC-2 - Brown/White * After programming, assign SWC buttons within radio menu
E1
E
E2
Aftermarket Radio Front (radio's features may vary)
Rear View Rear
AUX-IN
Sub
SWC
3.5mm Adapter for Vehicles without Steering wheel controls 1) From the 3.5mm adapter, tie the Brown and Brown/White wires together with tape or connector 2) Connect the 3.5mm adapter to the 3.5mm jack from the AXTC-HN1 Harness 3) Program the AXTC-HN1 per the instructions on page 3. Disregard steps 4 & 5
2
AXCSD-6V
*Harness #
LD-AFDI-5V *
VEHICLE CONNECTORS
RADIO CONNECTIONS
Gray - Front right speaker + Gray/Black - Front right speaker White - Front left speaker + White/Black - Front left speaker Green - Rear left speaker + Green/Black - Rear left speaker Purple - Rear right speaker + Purple/Black - Rear right speaker Blue/Pink - VSS/Speed-Sense Green/Purple - Reverse signal Light Green - Parking brake Blue/White - Amp turn-on Orange - Illumination Yellow - Battery power
SWC GROUND
Black & Black X2 - Ground
(Connect All Grounds Together)
CAMERA POWER 6V
Red (CAMERA POWER 6V) & Blue/Red - Camera Power Red & Blue/White - Accessory power
PROGRAMMING
1.
Open the driver's door, and keep open during the programming process. 6.
The LED will go out, then once again quickly flash Green & Red while
the interface programs itself to the vehicle. Once programmed, the LED
Green & Red LED will go out again, then turn solid Green.
OF F
START
2.
ACC ON
Cycle the ignition on.
Green LED
7.
ACC ON
Cycle the ignition off, then back on.
START
OF F
3.
Connect the AXTC-HN1 harness to the AXTC-HN1 interface, and then to
the wiring harness in the vehicle.
ACC ON
START
OF F
4.
The AXTC will enter auto-detect mode. No additional action is required. 8.
Test all functions of the installation for proper operation.
5*.
The LED will flash Green & Red while the interface programs the radio to
the steering wheel controls. Once programmed, the LED will go out, then
Green & Red LED produce a pattern which will identify the radio type installed. Refer to
the Radio LED Feedback section under Troubleshooting for radio types.
*Only applicable if vehicle came with steering wheel controls
Green or Red LED
Note: If the vehicle's Steering Wheel Controls do not function after the AXTC-HN1 has completed its programing sequence, unplug connector E1 from connector E and connect E2 to E. Once completed, hit the reset button on the interface to restart the programming sequence and test. Refer to LED Feedback Chart for programming information if needed.
REV. 6/6/24 INSTAXTC-HN1 3
AXTC-HN1
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING
1.
If the interface fails to function, 2. Final LED Feedback
press and release the reset button, then repeat the programming process from step 4 to try again.
At the end of programming the LED will turn Solid Green which indicates programming was successful. If the LED didn't turn Solid Green, reference the list below to understand which programming section the problem may stem from.
LED
Reset
Light
Button
QR Code Scan Here
Further troubleshooting steps and information can be located at: axxessinterfaces.com/product/AXTC-HN1
LED Light
Solid Green Slow Red Flash Slow Green Flash
Solid Red
Radio Programming
Section Pass Fail Pass Fail
Vehicle Programming
Section Pass Pass Fail Fail
Note: If the LED shows Solid Green for Pass (indicating everything programmed correctly), yet the steering wheel controls don't work, make sure that the 3.5mm jack is plugged in, and plugged into the correct jack in the radio. Once corrected, press the reset button, then program again.
Having difficulties? We're here to help. Contact our Tech Support line at:
386-257-1187
Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 5:00 PM Sunday: 10:00 AM - 4:00 PM
Metra recommends MECP certified technicians
AxxessInterfaces.com
© COPYRIGHT 2024 METRA ELECTRONICS CORPORATION
REV. 6/6/24 INSTAXTC-HN1