User Manual for TELTONIKA models including: FMM920 Small and Smart Tracker, FMM920, FMM920 Smart Tracker, Small and Smart Tracker, Smart Tracker, Small Tracker, Tracker
FMM920 - Teltonika Telematics
prieš 21 valandą — Quick Manual v1.9 // FMM920 ... setup. 1 teltonika-gps.com/downloads/en/FMM920/TeltonikaCOMDriver.zip ... LED's should start blinking, see “LED.
FMM920
setup. 1 teltonika-gps.com/downloads/en/FMM920/TeltonikaCOMDriver.zip ... Connect device to computer using Micro-USB cable or Bluetooth connection:.
FMM920
Small and smart tracker
Quick Manual v1.9
CONTENT
Know your device................................................................................................................................................................................................3 Pinout ...................................................................................................................................................................................................................4 Wiring scheme.....................................................................................................................................................................................................5 Set up your device ..............................................................................................................................................................................................6 PC Connection (Windows)..................................................................................................................................................................................7 How to install USB drivers (Windows) ..............................................................................................................................................................7 Configuration.......................................................................................................................................................................................................8 Quick SMS configuration................................................................................................................................................................................. 10 Mounting recommendations.......................................................................................................................................................................... 12 Basic characteristics ........................................................................................................................................................................................ 13 LED indications................................................................................................................................................................................................. 13 Electrical characteristics.................................................................................................................................................................................. 16 Safety information .......................................................................................................................................................................................... 17 Certification and Approvals ............................................................................................................................................................................ 18 Warranty ........................................................................................................................................................................................................... 19 Warranty disclaimer ....................................................................................................................................................................................... 19
Telematics
Quick Manual v1.9 // FMM920 2
KNOW YOUR DEVICE
TOP VIEW (WITHOUT COVER)
POWER CABLE
BOTTOM VIEW (WITHOUT COVER)
MICRO-USB
NAVIGATE LED
STATUS LED
Telematics
BATTERY SOCKET
MICRO-SIM SLOT
Quick Manual v1.9 // FMM920 3
PINOUT
PIN NUMBER PIN NAME
DESCRIPTION
1
VCC (10-30) V DC (+)
(Red) Power supply (+10 -30 V DC)
+10...30 V DC
1
2
GND (-)
(Black) Ground
GND
2
(Yellow) Digital input,
3
DIN1
channel 1. DEDICATED FOR IGNITION INPUT
DIN1
3
4
AIN1
(Grey) Analog input, channel 1. Input range:
AIN1
4
0-30 V DC
DOUT1
5
(White) Digital output.
5
DOUT1
Open collector output.
Max. 0,5 A DC
FMM920 pinout
Telematics
Quick Manual v1.9 // FMM920 4
WIRING SCHEME
IGNITION DETECTION
87 87a 86 85 30
ALARM BUTTON
DOOR SENSOR
+10...30 V DC
1
GND
2
DIN1
3
AIN1
4
DOUT1
5
FUEL GAUGE
BUZZER
STARTER
ANALOG LLS SENSOR
POWER SUPPLY 10 - 30V DC
Telematics
Quick Manual v1.9 // FMM920 5
SET UP YOUR DEVICE
HOW TO INSERT MICRO-SIM CARD
1 COVER REMOVAL
2 MICRO-SIM CARD INSERT
3 REMOVING PROTECTION
Gently remove FMM920 cover using plastic pry tool from both sides.
Insert Micro-SIM card as shown with PIN request disabled or read Security info1how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
Remove the adhesive tape protection.
4 PLACING BATTERY
5 CONNECTING BATTERY
Place the battery inside the casing of the FMM920. Make sure the adhesive tape sticks to the casing.
Connect the internal battery to the FMM920 PCB.
https://wiki.teltonika-gps.com/view/FMM920_Security_info1 Telematics
6 ATTACHING COVER BACK
Attach device cover back. Device is ready to be connected.
Quick Manual v1.9 // FMM920 6
PC CONNECTION (WINDOWS)
1. Power-up FMM920 with DC voltage (10 30 V) power supply using power wires. LED's should start blinking, see "LED indications1".
2. Connect device to computer using Micro-USB cable or Bluetooth connection: · Using Micro-USB cable · You will need to install USB drivers, see "How to install USB drivers (Windows)2" · Using Bluetooth · FMM920 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named "FMM920_last_7_imei_digits", without LE in the end. · Enter default password 5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.
1Page 13, "LED indications" 2Page 7, "How to install USB drivers (Windows)"
HOW TO INSTALL USB DRIVERS (WINDOWS)
1. Please download COM port drivers from here1. 2. Extract and run TeltonikaCOMDriver.exe. 3. Click Next in driver installation window. 4. In the following window click Install button. 5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the
setup.
1teltonika-gps.com/downloads/en/FMM920/TeltonikaCOMDriver.zip
Telematics
Quick Manual v1.9 // FMM920 7
CONFIGURATION
At first FMM920 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
1wiki.teltonika-gps.com/view/Teltonika_Configurator 2wiki.teltonika-gps.com/view/Teltonika_Configurator_versions
MS .Net requirements
Operating system Windows Vista Windows 7 Windows 8.1
Windows 10
MS .NET Framework version Version
MS .NET 5.0
32 and 64 bit
1dotnet.microsoft.com/en-us/download/dotnet/5.0/runtime
Links www.microsoft.com1
Telematics
Quick Manual v1.9 // FMM920 8
Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5 and etc. FMM920 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:
Downloaded Configurator will be in compressed archive.
Extract it and launch Configurator.exe. After launch software language can be changed by clicking in the right bottom
corner.
Load from device loads configuration from device. Save to device saves configuration to device. Load from file loads configuration from file.
Save to file saves configuration to file.
Configuration process begins by pressing on connected device.
Update firmware updates firmware on device. Read records reads records from the device.
Reboot device restarts device.
After connection to Configurator Status window will be displayed.
Reset configuration sets device configuration to default.
Most important configurator section is GPRS where all your server and GPRS settings6 can be configured and Data Acquisition7 where data acquiring parameters can be configured. More details about FMM920 configuration using Configurator can be found in our Wiki8. 1wiki.teltonika-gps.com/view/FMM920_Status_info 2wiki.teltonika-gps.com/view/FMM920_Status_info#GNSS_Info 3wiki.teltonika-gps.com/view/FMM920_Status_info#GSM_Info 4wiki.teltonika-gps.com/view/FMM920_Status_info#I.2FO_Info 5wiki.teltonika-gps.com/view/FMM920_Status_info#Maintenance 6wiki.teltonika-gps.com/view/FMM920_GPRS_settings 7wiki.teltonika-gps.com/view/FMM920_Data_acquisition_settings 8wiki.teltonika-gps.com/view/FMM920_Configuration
Telematics
Quick Manual v1.9 // FMM920 9
QUICK SMS CONFIGURATION
Default configuration has optimal parameters present to ensure best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it:
« setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0»
1
2
3
4
5
6
Note: Before SMS text, two space symbols should be inserted.
GPRS SETTINGS: 1 2001 APN
2 2002 APN username (if there are no APN username, empty field should be left)
3
2003 APN password (if there are no APN password, empty field should be left)
SERVER SETTINGS: 4 2004 Domain 5 2005 Port 6 2006 Data sending protocol (0 TCP, 1 UDP)
Telematics
Quick Manual v1.9 // FMM920 10
DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION: VEHICLE MOVEMENT will be detected by accelerometer
DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:
300 seconds passes
VEHICLE TURNS 10 degrees
IGNITION WILL BE DETECTED by vehicle power voltage between 13,2 30 V
VEHICLE DRIVES 100 meters
SPEED DIFFERENCE between last coordinate and current position is greater than 10 km/h
DEVICE MAKES A RECORD ON STOP IF:
RECORDS SENDING TO SERVER:
1 HOUR PASSES while vehicle is stationary and ignition is off
IF DEVICE HAS MADE A RECORD it is sent to the server every 120 seconds
After successful SMS configuration, FMM920 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.
1wiki.teltonika-gps.com/view/Teltonika_Configurator 2wiki.teltonika-gps.com/view/Template:FMB_Device_Family_Parameter_list
Telematics
Quick Manual v1.9 // FMM920 11
MOUNTING RECOMMENDATIONS
CONNECTING WIRES
· Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
· The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
· If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
· Wires cannot be connected to the board computers or control units.
CONNECTING POWER SOURCE
· Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in 5 to 30 minutes period.
· When module is connected, measure voltage again to make sure it did not decrease. · It is recommended to connect to the main power cable in the fuse box. · Use 3A, 125V external fuse.
CONNECTING IGNITION WIRE
· Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine. · Check if this is not an ACC wire (when key is in the first position, most of the vehicle electronics are available). · Check if power is still available when you turn off any of vehicles devices. · Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on,
may be chosen.
CONNECTING GROUND WIRE
· Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame. · If the wire is fixed with the bolt, the loop must be connected to the end of the wire. · For better contact scrub paint from the spot where loop is going to be connected.
Telematics
Quick Manual v1.9 // FMM920 12
LED INDICATIONS
NAVIGATION LED INDICATIONS
Behaviour
Meaning
Permanently switched on
GNSS signal is not received
Blinking every second
Normal mode, GNSS is working
GNSS is turned off because:
Off
Device is not working or Device is in
sleep mode
Blinking fast constantly
Device firmware is being flashed
STATUS LED INDICATIONS
Behaviour
Meaning
Blinking every second
Normal mode
Blinking every two seconds
Sleep mode
Blinking fast for a short time
Modem activity
Off
Device is not working or Device is in boot mode
Telematics
BASIC CHARACTERISTICS
Module Name Technology
FMM920-Q3IB0: Quectel BG95-M3 with Teltonika TM2500
LTE Cat M1/NB-IoT/GSM/GPRS/ GNSS/BLUETOOTH
GNSS
GNSS
Receiver Tracking sensitivity Accuracy Hot start Warm start Cold start
GPS, GLONASS, GALILEO, BEIDOU, QZSS, AGPS 33 channel -165 dBM < 3 m < 1 s < 25 s < 35 s
Celluar Technology 2G bands
4G bands
LTE Cat M1/NB-IoT/GSM
GPRS: B2/B3/B5/B8
Cat M1: B1/B2/B3/B4/B5/B8/ B12/ B13/B18/B19/ B20/B25/B27/ B28/ B66/B85 Cat NB2: B1/B2/B3/B4/B5/B8/ B12/ B13/B18/B19/ B20/B25/B28/B66/ B71/B85
Quick Manual v1.9 // FMM920 13
Data transfer Transmit power
BG95: Cat M1: Max. 588Kbps (DL)/ Max.1119Kbps (UL) Cat NB2: Max. 127Kbps (DL)/Max. 158.5Kbps (UL) GPRS: Max. 107Kbps (DL)/Max. 85.6Kbps (UL)
Class 4 for GSM850/900: 32±2dBm Class 1 for GSM1800/1900: 30±2dBm Class 3 for LTE-TDD: 23±2.7dBm Class 3 for LTE-FDD: 23±2.7dBm Bluetooth: 4.57dBm +/-2dBm Bluetooth LE: -4.83dBm +/-2dBm
Power
Input voltage range
10 - 30 V DC with overvoltage protection
Back-up battery
170 mAh Li-Ion battery (0.63 Wh)
Internal fuse
3A, 125 V
Power consumption
At 12V < 2 mA (Ultra Deep Sleep) At 12V < 3 mA (Deep Sleep) At 12V < 8 mA (Online Sleep) At 12V < 12 mA (GNSS Sleep) At 12V < 28 mA (Nominal with no load) At 12V < 250 mA Max. (with full Load / Peak)
Bluetooth Specification
Supported peripherals
4.0 + LE
Temperature and Humidity sensor1, OBDII dongle2, Inateck Barcode Scanner,Universal BLE sensors support
INTERFACE Digital Inputs Digital Outputs Analog Inputs GNSS antenna Cellular antenna USB LED indication SIM Memory
1 1 1 Internal High Gain Internal High Gain 2.0 Micro-USB 2 status LED lights Micro-SIM 128MB internal flash memory
1teltonika.lt/product/bluetooth-sensor
2wiki.teltonika.lt/view/How_to_connect_OBD_II_Blue-tooth_Dongle_to_ FMB_device
Telematics
Quick Manual v1.9 // FMM920 14
Physical Specification Dimensions Weight
79 x 43 x 12 mm (L x W x H) 54 g
Operating Environment
Operating temperature (with
battery)
-20 °C to +40 °C
Operating temperature (without battery)
-40 °C to +85 °C
Storage temperature (without battery)
-40 °C to +85 °C
Operating humidity 5% to 95% non-condensing
Ingress Protection Rating
IP54
Battery charge temperature
0 °C to +45 °C
Battery discharge temperature
-20 °C to +60 °C
Battery storage temperature
-20 °C to +45 °C for 1 month -20 °C to +35 °C for 6 months
Features Sensors
Accelerometer
Telematics
Scenarios
Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip3
Sleep modes
GPS Sleep, Online Deep Sleep, Deep Sleesp, Ultra Deep Sleep4
Configuration and firmware update
FOTA Web5, FOTA6, Teltonika Configurator7 (USB, Bluetooth), FMBT mobile application8 (Configuration)
SMS
Configuration, Events, DOUT Control, Debug
GPRS commands
Configuration, Debug
Time Synchronization
GPS, NITZ, NTP
Fuel monitoring
LLS (Analog), OBDII dongle9
Ignition detection
Digital Input 1, Accelerometer, External Power Voltage, Engine RPM (OBDII dongle14)
3wiki.teltonika-gps.com/view/FMM920_Features_settings 4wiki.teltonika-gps.com/view/FMM920_Sleep_modes 5wiki.teltonika-gps.com/view/FOTA_WEB 6wiki.teltonika-gps.com/view/FOTA 7wiki.teltonika-gps.com/view/Teltonika_Configurator 8wiki.teltonika-gps.com/view/FMBT_Mobile_application 9wiki.teltonika-gps.com/view/How_to_connect_OBD_II_Bluetooth_ Dongle_to_FMB_device
Quick Manual v1.9 // FMM920 15
ELECTRICAL CHARACTERISTICS
Characteristic description
Value
Supply voltage
Min.
Typ.
Supply Voltage
(Recommended
+10
Operating Conditions)
Max. Unit +30 V
Digital output (open drain grade)
Drain current (Digital Output OFF)
Drain current (Digital Output ON, Recommended Operating Conditions)
Static Drain-Source resistance (Digital Output ON)
120 µA
0.5
A
300 m
Digital input
Input resistance (DIN1) 47
k
Input voltage
(Recommended
0
Operating Conditions)
30
V
Input Voltage threshold
2.5
V
Characteristic description
Value
Supply voltage
Min.
Typ.
Max. Unit
Analog input
Input Voltage
(Recommended
0
Operating Conditions)
Input resistance
Measurement error on 12V
Additional error on 12V
Measurement error on 30V
Additional error on 30V
30
V
150
k
3
%
360
mV
3
%
900
mV
Telematics
Quick Manual v1.9 // FMM920 16
SAFETY INFORMATION
This message contains information on how to operate FMM920 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!
· The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10...+30 V DC.
· To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
· When connecting the connection (1x5) cables to the vehicle, the appropriate jumpers of the power supply of the vehicle should be disconnected.
· Before dismounting the device from the vehicle, the 1x5 connection must be disconnected.
· The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard.
· The device FMM920 is not designed as a navigational device for boats.
Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the powe supply.
All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with autonomic power supply.
Installation and/or handling during a lightning storm is prohibited.
The device is susceptible to water and humidity.
Telematics
Quick Manual v1.9 // FMM920 17
CERTIFICATION AND APPROVALS
This sign on the package means that it is necessary to read the User`s Manual before your start using the device. Full User`s Manual version can be found in our Wiki1.
1wiki.teltonika-gps.com/view/FMM920
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
FCC ID: 2A3HUFMM920
· This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
· This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help. · Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. · This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2. 2 wiki.teltonika-gps.com/view/FMM920_Certification_%26_Approvals
Telematics
Quick Manual v1.9 // FMM920 18
WARRANTY
TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager.
Contact us teltonika-gps.com/about-us/contacts
All batteries carry a reduced 6 month warranty period. If a product should fail within this specific warranty time, the product can be: · Repaired · Replaced with a new product · Replaced with an equivalent repaired product fulfilling the same functionality · TELTONIKA can also repair products that are out of warranty at an agreed cost.
WARRANTY DISCLAIMER
TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC LOSS. More information can be found at teltonika-gps.com/warranty-repair
Telematics
Quick Manual v1.9 // FMM920 19
Download .NET 5.0 Runtime
Teltonika Telematics
FMM920 Certification & Approvals - Teltonika Telematics Wiki
teltonika.lt/product/bluetooth-sensor/