HELLA Sonnen- und Wetterschutztechnik GmbH
Installation Guide for HELLA models including: ISPL18 Pleated Insect Screen, ISPL18, Pleated Insect Screen, Insect Screen, Screen
File Info : application/pdf, 16 Pages, 2.39MB
DocumentDocumentInstallation instructions These instructions must be read prior to installation and use! Pleated insect screen Installation instructions Table of Contents Preliminary remarks HELLA Pleated insect screen ..............................................................3 Before installation.................................................................................................................4 Overview: Tools for the installation.......................................................................................5 Overview: ISPL18 Pleated insect screen..............................................................................6 Installation ISPL18 Pleated insect screen 18 mm ................................................................7 Commissioning/functional check ........................................................................................ 12 Replacing the pleated insect screen with cords..................................................................13 Removal ............................................................................................................................. 15 Installation instructions Preliminary remarks HELLA Pleated insect screen With this HELLA product you have opted for a high-quality product with a most up-to-date technology that can nevertheless be easily installed and operated. In these instructions we describe the basic installation, commissioning and use. For authorized specialist staff For the consumer (user) The following symbols will assist you with the installation or use and require a safetyconscious conduct: Attention! This symbol indicates instructions that, if disregarded, can put the user in danger. Attention! This symbol indicates instructions that, if disregarded, can potentially result in damage to the product. This symbol indicates instructions for use or helpful information. This symbol requires you to act. Attention! This symbol indicates a risk of injury or danger to life due to an electric shock. This symbol indicates parts of the product, for which you will find important information in these installation instructions. Attention! This symbol indicates possible risk of injury by crushing. This symbol indicates the cleaning of the product. This symbol indicates the maintenance and repair of the product. Subject to technical modifications Date of Issue April/2024 3 Installation instructions Before installation Check the product immediately for possible shipping damage and for compliance with the delivery receipt. If parts are missing or damaged, please consult your supplier immediately. Check the mounting base and ensure that the mounting material to be used complies with the given conditions to guarantee proper installation. In case of doubt, please seek advice from a specialist enterprise for fixing techniques. The packaging cardboard box should not be exposed to humidity. To protect it from rain during transport, it should be covered by a foil. Carry larger units by two persons. Transport and store the units carefully to prevent injury of persons and damage to the product. Remove the packaging material carefully. When using a knife, be careful not to damage the packaging content and to avoid cuts! Dispose of the packaging material via recycling. Caution! A wrong installation can endanger the user seriously. Please strictly observe the installation instructions. Close off the place of installation. When working at higher heights, there is risk of falling. Suitable ascent supports, scaffoldings and fall protection devices are to be used. Please make sure that the ascent supports stand solidly and provide a firm grip. 4 Subject to technical modifications Date of Issue April/2024 Installation instructions Overview: Tools for the installation Battery-powered drill Drill Depending on the Drill set mounting base (Bit AW 20, acc. to Mounting base AW 25) Bit extension Level Measuring tape Pin Screwdriver Allen key Blind rivetting tongs Subject to technical modifications Date of Issue April/2024 5 Installation instructions Overview: ISPL18 Pleated insect screen Legend 1 1 Installation profile at the top 2 Guide rail at the top 2 3 Holding device for guide rail at the top 3 4 Pleated blind package consisting of: 4 - Screen with cords - Wall profiles with end caps - Handle profile with end caps 5 5 Mounting clip 6 Holding device for slide rail at the bottom 7 Slide rail at the bottom 6 7 6 Subject to technical modifications Date of Issue April/2024 Installation instructions Installation ISPL18 Pleated insect screen 18 mm 1 2 3 4 Legend 1 Frame profile 2 Corner joint 3 Covering cap 4 Plastic clip profile with adhesive tape Installation frame (optional) Stick the frame profiles (1) and the corner joints (2) together and adjust them to the mounting base. Mark the boreholes on the mounting base and provide the boreholes according to the mounting base to be used. Screw the installation frame to the mounting base and close the boreholes with the covering caps (3). Optionally it is possible to mount the installation frame without screws. For this purpose a plastic clip profile (4) with double-sided adhesive tape is used. Subject to technical modifications Date of Issue April/2024 7 Installation instructions Installation ISPL18 Pleated insect screen 18 mm Installation of the guide rail at the top Screw the mounting profile 1 (1) at the top to the mounting base or installation frame. Insert the holder (3) into the upper guide rail (2) and 2 clamp it with a headless screw. Using the holder and 3 the slot nut (4), screw the upper guide rail laterally at the top to the mounting base or installation frame: 100 4 Legend 1 Installation profile at the top 2 Guide rail at the top 3 Holding device for guide rail at the top 4 Slot nut for guide rail holder 8 Subject to technical modifications Date of Issue April/2024 Installation instructions Installation ISPL18 Pleated insect screen 18 mm 2 3 1 Installation of the slide rail at the bottom Insert the holding devices (1) into the lower slide rail (2) and remove the protective foil from the adhesive tape. Glue the slide rail in parallel and vertical alignment beneath the upper guide rail to the mounting base or installation frame (punchings for water drainage face towards the outside) Screw the holding devices (1) and mounting clips (3) at medium height to the mounting base resp. mounting bracket (the screws face towards the outside). Legend 1 Holding devices for lower slide rail 2 Lower slide rail 3 Mounting clip Subject to technical modifications Date of Issue April/2024 9 Installation instructions Installation ISPL18 Pleated insect screen 18 mm 1 2 3 4 Attaching the pleated blind package Insert the pleated blind package into the upper and lower slide rain and hinge it in the numbered order as shown in the illustration. Ensure that the lower cords are not crossed and are inside the C-shaped guide rail. If the cords are not brought to the intended position, operation is more difficult and the cords may be pushed out of the rail. Over a longer period of time, this can damage the pleating. 10 Subject to technical modifications Date of Issue April/2024 Installation instructions Installation ISPL18 Pleated insect screen 18 mm 1 2 2 3 The unit is set to the ordered width in the factory so that no adjustments need to be made to the cords at the site. Tensioning of the cords 1. Remove the magnetic profile, which is placed on the side of the limit stop, laterally from the wall profile. 2. Release the threaded pins provided at the cold holders, and shift the holders until the cords are tensioned. Clamp the threaded pins. 3. Now press the magnetic profile into the wall profile again. 4. Tension the individual cords on the opposite side via the slotted holes in the screen-side wall profile The cord tension must be selected in such a way, that the cords do not sag and that the pleated insect screen is still running smoothly. Cords that are too tight will damage the unit as they cut into the plastic deflectors. Subject to technical modifications Date of Issue April/2024 11 Installation instructions Commissioning/functional check Please check the unit for proper functioning before handing over. Check all settings. Check all screwed connections for tightness. Clean the elements (see maintenance instructions). Give these instructions to the user. Introduce the user by informing him about the safety instructions and instructions for use of the unit. Have the correct design of the unit, the installation and the introduction with the safety instructions confirmed in writing (see handing over report). 12 Subject to technical modifications Date of Issue April/2024 Installation instructions Replacing the pleated insect screen with cords 1. 1. 1. 3. 2. 4. Lift the pleated package and unhinge it out of he mounting clips. 1. Remove the screws that fix the side covers to the handle profile. Remove the side covers from the profiles and pull the cords out. 2. Remove the magnetic profile, which is placed on the side of the limit stop. 3. Remove the threaded pins provided at the cord holders and pull the cord holders at the top and at the bottom out of the wall profile. 4. Pull the pleated package out of the profiles. 5. With older pleated blind designs, loosen one clamping screw per cord on the wall profile. Furthermore, remove any existing suspension hooks from the wall profiles, and refit them after the net has been replaced. 5. 5. Subject to technical modifications Date of Issue April/2024 13 Installation instructions Replacing the pleated insect screen with cords 1. 2. 4. 3. 3. 3. The lower side covers are recognizable by the lower retraction depth of the guide rail. The bottom side of the pleated package is recognizable by the two cords and the smaller edge distance of the first cord. 1. Insert the new pleated package into the profiles. 2. Push the cord ends into the wall profile and clamp them. 3. Insert the lower side covers into the cords, put them onto the profiles and screw them to the handle rail. 4. Cut the lower cords above the side covers. 5. Cut the pleated screen at the top to the length of the old pleated screen using a cutter knife. 6. Insert the upper side covers into the cords, put them onto the profiles and screw them to the handle rail. When shortening the pleated 6. screen, make sure that the cords do not get damaged. 6. 6. For information regarding the remounting of the pleated package, the tensioning of the cords and the pushing in of the magnet, please refer to the appropriate chapters in these instructions. 14 Subject to technical modifications Date of Issue April/2024 Installation instructions Removal The removal is carried out in reverse order to the installation. Subject to technical modifications Date of Issue April/2024 15 Installation instructions HELLA Interior Venetian Blinds regulate the lighting in a room very comfortably, immediately gracing it with much more atmosphere. HELLA Insect screens and you decide who is allowed to come in and who isn't. HELLA Pleated Blind folds up very compactly and protects very well against the sun and nosey glances where only little space is available. HELLA Outdoor Blinds HELLA Front-mounted HELLA Vertical awning serve for the light Roller Shutter with toggle catch regulation, as view for more safety and mechanism for a lovely protection, anti-glare blind protection against rain, façade design with perfect and heat protection. wind, heat, the cold, noise, heat and glare protection. incident light and nosey glances, also available for subsequent installation. For questions, wishes and ideas: HELLA Infoline +43/(0)4846/6555-0 HELLA Sonnen- und Wetterschutztechnik GmbH A-9913 Abfaltersbach, No. 125 Phone: +43/(0)4846/6555-0 Fax: +43/(0)4846/6555-134 e-mail: office@hella.info Internet: http://www.hella.info