OpenEye - Cloud Managed Video Surveillance OpenEye Logo
OpenEye - Cloud Managed Video Surveillance | OpenEye
User Guide for OpenEye models including: OE-C7032-WR, 2MP Mini Dome IP Camera, OE-C7032-WR 2MP Mini Dome IP Camera, Dome IP Camera, IP Camera, Camera, 35302AF
NOTE:Refer to your Apex recorder manual or quick start guide for instruction on adding cameras. Passwords must be 9-32 characters including at least two elements of the following three: digits, letters, and special characters. NOTE:To change this IP address please refer to your Apex recorder manual. NOTE:NCM requires entry in all fi elds.
NOTE: To change this IP address please refer to your Apex recorder manual. NOTE: NCM requires entry in all fields. ASSIGNING AN. IP ADDRESS. OpenEye IP ...
File Info : application/pdf, 2 Pages, 894.58KB
DocumentDocumentCONNECTIONS 1 1 RJ-45 2 Power (12vDC) For network and PoE connections 1 12vDC Power connection This quick start guide provides only basic information on the camera's settings and operation for initial installation. Please read the user manual for optimal camera configurations. To restore the camera to factory 1 defaults: 1. Disconnect power for 30 1 Reset Button seconds. 2. Reconnect power and wait 30 seconds. 3. Press and hold the reset button for 20 seconds. Supports up to 128GB microSD card 2 MicroSD Card Slot for Edge storage. Do not add or remove the microSD card when the camera is powered on. Waterproof Cable 5 4 3 2 1 1 Thread lock cap 2 Rubber plug 3 RJ45 enclosure 4 Rubber "O" ring 5 Camera cable Liberty Lake, WA, USA 509.232.5261 openeye.net Copyright ©2021 OpenEye. All Rights Reserved. Information contained in this document is subject to change without prior notice. OpenEye does its best to provide accurate information but cannot be held responsible for typos or mistakes. 35302AF QUICK START GUIDE OE-C7032-WR 2MP Mini Dome IP Camera openeye.net CONTENTS OE-C7032-WR Dome Camera Waterproof Cable Security Torx Tool Self-Tapping Screws & Plastic Anchors Mounting Template Paintable Cover Quick Start Guide INSTALLATION 1. Apply template sticker to desired camera location. 2. Drill anchor holes using included mounting template. 3. Remove mounting template. 4. Insert anchors. 5. Mount camera. 6. Connect network cable with included waterproof cable connector. 7. Adjust camera view. 8. Secure Lid / dome NOTE: If the camera will be exposed to inclement weather, OpenEye recommends sealing around the camera base, or connection to mounting surface with outdoor waterproof caulking. ETHERNET CABLE CONNECTIONS Connect a network cable to the camera using the RJ45 input and connect the other end of the cable to your network switch or recorder. POWER This camera is compatible with 12vDC and Power over Ethernet (PoE). If you are connecting 12vDC power, verify the polarity of the power connection. DEFAULT USERNAME AND PASSWORD NOTE: OpenEye IP cameras ship without a default password. The admin user password can be set using the following methods: 1. OpenEye recorders running Apex 2.1 or newer will automatically set a new unique password if: · Connected to an M-Series recorder with a built in PoE switch. · Connected to a network switch through the camera network port and selected then added in setup, if a new password has not already been set. 2. Connect to the camera directly through a Web Browser and follow the onscreen prompts. 3. Use the Network Camera Manager (NCM) Utility. Username: admin NOTE: The NCM software manual can be found at https://www.openeye.net/ ncm-manual NOTE: Refer to your Apex recorder manual or quick start guide for instruction on adding cameras. Passwords must be 9-32 characters including at least two elements of the following three: digits, letters, and special characters. ASSIGNING AN IP ADDRESS OpenEye IP cameras are set to DHCP by default. If a DHCP server is not detected after 4 minutes, the camera will default to IP address 192.168.51.2. If you are not using a DHCP server, NCM will allow you to batch configure a static IP address. The IP address for the camera network on your Apex recorder is 192.168.51.1. NOTE: To change this IP address please refer to your Apex recorder manual. Selecting multiple cameras and entering IP address 192.168.51.2 will set an IP address on all selected cameras, starting at 192.168.51.2 and increase per camera. 1. Open Network Camera Manager. 2. Select applicable camera(s). 3. Input starting IP address, Subnet Mask, Gateway, DNS. NOTE: NCM requires entry in all fields. 4. Apply changes. 5. Wait 60 seconds before refreshing NCM. CONNECTING TO THE IP CAMERA To access the camera setup menu, you need to open Network Camera Manager (NCM) utility. NCM is preinstalled on all OpenEye Recorders, and is also available for download on the OpenEye website for installation on your personal computer or laptop. 1. Open Network Camera Manager. 2. Locate your camera on the Network Camera Manager list. 3. To open the web browser, select the camera and click LOAD. PRODUCT FEATURES Camera Maximum Resolution 1920x1080 Frame Rate at Maximum Resolution 30FPS @ 2MP H.264/H.265 Total Streams Dual Streaming ONVIF Profile S / G Compliant Day/Night True Day / Night Wide Dynamic Range True WDR Environmental and Power Power Consumption 5.5W Max Input Voltage Operating Temperature IP Rating 12vDC / PoE -31°~140°F (-35°~60°C ) IP67 Impact Rating IK10