Instructions for GAGGENAU models including: VG425211 Vario Gas Cooktop, VG425211, Vario Gas Cooktop, Gas Cooktop, Cooktop
Gaggenau.com View all center › Url: https://media3.gaggenau.com/ /specsheet/en-ZZ/VG425211
Color Variants VG425211 Stainless steel Width 38 cm Installation Accessories VA420004 Connection strip for combination with other Vario appliances of the 400 series for flush mounting VA420010 Connection strip for combination with other Vario appliances of the 400 series for surface mounting VA440010 Stainless steel appliance cover with mounting strip VG425211 Vario gas cooktop 400 series Stainless steel Width 38 cm Natural gas 20 mbar Multi-ring burner with up to 4 kW Full electronic power level regulation on 12 levels Precise and reproducible flame size Automatic fast ignition, electronic flame monitoring with automatic re-ignition Simmer function for cooking on a very low output level Solid stainless steel control knob Precision crafted 3 mm stainless steel For surface mounting with a visible edge or for flush mounting Can be combined perfectly with other Vario appliances of the 400 series Cooking zones 1 two-ring high output burner (165 W 4000 W), suitable for pots up to max. ø 28 cm. 1 two-ring standard output burner (165 W 2000 W), suitable for pots up to max. ø 24 cm. Handling Control knobs with illuminated ring, cooking zone and output level markings. One-handed operation. Full electronic control in 12 output levels for exact power level regulation plus simmer function. Automatic fast ignition. Features Simmer function. Cast iron pan support with flat, continuous pot surface. Brass burner rings. Safety Electronic flame monitoring with automatic re-ignition. Residual heat indication. Safety shut-off. Planning notes Depending on the type of installation (surface-mounted or flush-mounted, with or without an appliance cover), the specific location of the cut-out and the knob positions may vary. The drawing "Installation of the control knob" must be observed if the panel is more than 23 mm thick (there must be a recess at the rear). If combining several Vario appliances of the 400 series, a connection strip VA 420 must be placed between the appliances. Depending on the type of installation, the corresponding connection strip must be provided. The bearing capacity and stability, in the case of thinner worktops in particular, must be supported using suitable substructures. Take into account the appliance weight and additional loads. Additional instructions for flush mounting: Installation is possible in worktops made of stone, synthetics or solid wood. Heat resistance and watertight sealing of the cut edges must be observed. Concerning other materials please consult the worktop manufacturer. The groove must be continuous and even, so that uniform placing of the appliance on the gasket is ensured. Do not use discontinuous lining. The joint width may vary due to size tolerances of the combinations and of the worktop cut-out. Characteristics Product name/family Vario/Domino gas hob Built-in / Free-standing Built-in Energy input Gas Total number of positions that can be used at the same time 2 Required niche size for installation (HxWxD) 134 x 360 x 492 Width of the appliance 380 Dimensions 158 x 380 x 520 Dimensions of the packed product (HxWxD) 300 x 500 x 600 Net weight 14.1 Gross weight 16.1 Residual heat indicator Separate Location of control panel External control Basic surface material brushed stainless steel Color of surface Stainless steel, Stainless steel Color of frame Stainless steel, Stainless steel Approval certificates CE, Eurasian, Ukraine, VDE Length electrical supply cord 140 Connection rating 15 Gas connection rating 6000 Fuse protection 2 Voltage 220-240 Frequency 60; 50 Consumption and connection features 2022-05-25 Page 1 If installing several appliances in individual cut-outs allow for a division bar of minimum 50 mm between the individual cut-outs. Special nozzles can be ordered as spare parts. Plan for an electrical connection (the appliance is not operable without power supply). Air intake from above. No intermediate shelf required. Rear panel and wall trims must be heat-resistant and consist of a nonflammable material. A minimum clearance of at least 150 mm from adjacent heat-sensitive furniture or contact surfaces must be observed or thermal insulation fitted. If operated next to the downdraft ventilation VL 414, the ventilation moulding AA 414 is recommended to ensure maximum performance of the cooktop. With a total connected load of more than 11 kW local regulations concerning room ventilation, room size and combination of extraction or recirculation hoods must be observed. The minimum distance between the cooktop surface and a cabinet above, out of combustible material, needs to be 70 cm. The minimum distance to a ventilation above is shown at the planning hints for the individual ventilation product. Appliance can be snapped into the worktop from above. Appliance weight: approx. 14 kg. Connection Total connected load gas 6.0 KW. Total connected load electric 15 W. Connecting cable 1.4 m with plug. VG425211 Vario gas cooktop 400 series Stainless steel Width 38 cm Natural gas 20 mbar 2022-05-25 Page 2 VG425211 Vario gas cooktop 400 series Stainless steel Width 38 cm Natural gas 20 mbar 2022-05-25 Page 3Apache FOP Version 2.3-bsh Apache FOP Version 2.3-bsh