User Guide for K-ARRAY models including: KT2 - KT2-HV, KT2C - KT2C-HV, KTL2 - KTL2-HV, Tornado Multi-Purpose 2 Inch Point Source Loudspeaker
Tornado 6 Ver 28 7. INCLUDED ACCESSORIES KT2 KT2C KTL2 KTL2C • 1 x M5 turned steel thumb nut • 1 x 4-pin Phoenix connector • 1 x Double threaded screw • 1 x Nylon anchor 6x30mm • 1 x Jumper cable • 1 x 4-pin Phoenix connector • 1 x Jumper cable • 1 x M5 turned steel thumb nut • 2 x 4-pin Phoenix connector • 1 x Double threaded screw • 1 x Nylon anchor 6x30mm
USER GUIDE. English ... This symbol alerts the user to the presence of recommendations about ... Before putting the device into operation, please.
4 giorni fa — professional or the use of ready-made leads or cords. ... Read these instructions - Keep these instructions - Heed all warnings ... 1 x Jumper cable.
File Info : application/pdf, 15 Pages, 1.36MB
DocumentDocumentVer. 2.8 Tornado KT2 - KT2-HV KT2C - KT2C-HV KTL2 - KTL2-HV KTL2C - KTL2C-HV USER GUIDE English KT2 - KT2-HV KTL2 - KTL2-HV KT2C - KT2C-HV KTL2C - KTL2C-HV NEW All Tornado models are also available in a 70V version! See Paragraph 9.1 for details. Tornado Ver. 2.8 TABLE OF CONTENTS SYMBOLS ................................................................................ 3 1. INTRODUCTION ..................................................................... 4 2. KEY FEATURES ...................................................................... 4 3. OPTIONAL FEATURE ............................................................... 4 4. APPLICATIONS....................................................................... 4 5. SAFETY INFORMATION............................................................ 5 6. UNPACKING ......................................................................... 5 7. INCLUDED ACCESSORIES ......................................................... 6 8. PHYSICAL ............................................................................. 6 9. REAR PANEL AND WIRING ....................................................... 7 9.1 70V VERSION..................................................................................... 8 10. INSTALLATION ..................................................................... 9 11. ACCESSORIES ......................................................................10 11.1 KA1-T2H WIRING ............................................................................... 11 12. SERVICE ............................................................................ 12 13. SPECIFICATIONS .................................................................. 13 14. KT2 AND KT2C EN54-24 DATA ............................................... 15 2 Tornado Ver. 2.8 SYMBOLS K-array declares that this device is in compliance with applicable CE standards and regulations. Before putting the device into operation, please observe the respective country-specific regulations! WEEE Please dispose of this product at the end of its operational lifetime by bringing it to your local collection point or recycling center for such equipment. This symbol alerts the user to the presence of recommendations about the product's use and maintenance. Warning! Dangerous voltages: RISK of electric shock. Terminals marked with this symbol are HAZARDOUS LIVE and the external wiring connected to these terminals requires installation by a qualified professional or the use of ready-made leads or cords. This symbol alerts the user to the presence of recommendations about product's use and maintenance. This device complies with Restriction of Hazardous Substances Directive. 3 Tornado 1. INTRODUCTION Ver. 2.8 The Tornado series is a miniature sound source designed for high-quality distributed systems. Housed in a compact aluminium enclosure, the Tornado is suitable for space sensitive and architectural design installations. The Tornados are a turn-key loudspeaker solution; designed as passive speakers, they can be easily converted into self-powered devices by inserting the KA1-T2H, 12V/24V amplifier module. All Tornado models are also available in a 70V version that can be powered with up to 100 units by a single KA84 amplifier channel and up to 50 units by two bridged KA24 amplifier channels. Tornados have a proprietary 2" high efficiency drive unit with a neodymium magnet structure and a suspension engineered for maximum linear excursion and minimum residual transducer interference. The cone transducer delivers an impressive maximum peak SPL of 107dB, and has a wide operating frequency range from 150 Hz to 18 kHz with very low distortion. In addition to the standard features of the Tornado loudspeakers, the KTL2 and KTL2C have 7 integrated RGB LEDs that can be controlled thanks the wide range of K-array accessories via DMX or by remote. With its ability to effortlessly reproduce speech, music and lighting, it is an excellent choice for fixed applications such as theatres, museum displays, restaurants, portable systems for corporate AV presentations, department stores, and in hidden locations such as chancel steps in houses of worship. The KT2 and KTL2 come with a wall bracket for fixed installations or surface applications. The KT2C and KTL2C come with ceiling brackets for ceiling mounts. All Tornado components are designed by the K-array R&D department and custom made under the K-array quality control system. 2. KEY FEATURES · High performance-to-size ratio · Single 2" long excursion full range driver · Integrated RGB LEDs (only KTL2 and KTL2C) · Wide-range frequency response · Integrated 4-pin Phoenix connector · Double voice-coil driver for variable impedance 8-32 · 70V version available · Compact aluminium ultra strong chassis · Weather resistant IP54 (only KT2 and KT2C) 4. APPLICATIONS · Audio for museum and exhibit displays · Space-sensitive fills and distributed systems for speech and music · Restaurants, clubs, pubs · Department stores · Installed audio-visual systems 3. OPTIONAL FEATURE · Self powered device using the KA1-T2H amplifier module (see Chapter 11) 4 Tornado 5. SAFETY INFORMATION Read these instructions - Keep these instructions - Heed all warnings Ver. 2.8 WARNING · Install the speaker only in a location that can structurally support the weight of the unit. Doing otherwise may result in the unit falling down and causing personal injury and property damage. · Professional loudspeakers are capable of producing extremely high sound levels and should be used with care. Hearing loss is cumulative and can result from levels above 90dB if people are exposed for an extended period. · Do not operate the speaker for an extended period of time with the sound distorting. This is an indication of malfunction, which in turn can cause heat to generate and result in a fire. · Never stand close to loudspeakers driven at high level. · Suspending the system should only be done by qualified personnel following safe rigging practices. Secure fixings to the building structure are vital. If in any doubt, seek help from architects, structural engineers or other specialists. · No naked flame sources such as lighted candles should be placed near the device. · Do not attempt to disassemble the unit. The unit contains no user serviceable parts.Repairs should be performed only by factory trained service personnel. CAUTION · Choking Hazards. This device contains small parts, which may present a choking hazard to small children. Keep the device and its accessories away from small children. · It is important that loudspeaker systems are used in a safe manner. · Do not make repairs yourself. Do not open the device, it contains potentially hazardous voltage. Never attempt to disassemble, repair or modify the system yourself. Disassembling the unit may cause damage that is not covered under the warranty. The device contains no user-serviceable parts. Repairs should only be performed by factory trained service personnel. 6. UNPACKING Each K-array amplifier is built to the highest standard and thoroughly inspected before leaving the factory. Upon arrival, carefully inspect the shipping carton, then examine and test your new amplifier. If you find any damage, immediately notify the shipping company. Only the consignee may institute a claim procedure regarding the system's electronic equipment. 5 Tornado 7. INCLUDED ACCESSORIES Ver. 2.8 KT2 KT2C KTL2 KTL2C · 1 x M5 turned steel thumb nut · 1 x M5 turned steel thumb nut · · · 1 x 4-pin Phoenix connector · 1 x Double threaded screw · 1 x Nylon anchor 6x30mm · 1 x 4-pin Phoenix connector · 1 x Jumper cable · 2 x 4-pin Phoenix connector · 1 x Double threaded screw · 1 x Nylon anchor 6x30mm 2 x 4-pin Phoenix connector 1 x Jumper cable · 1 x Jumper cable · 1 x Jumper cable 8. PHYSICAL 2,9in 74,2mm 4,6in 117,5mm 1,8in 46,9mm 4,8in 121mm 4,8in 122,6mm 3,7in 95mm 4,0in 102mm 4,9in 125mm Weight Table Kg lb KT2 0.56 1.23 6 KT2C 0.67 1.48 4,6in 116,75mm 4,7in 118,75mm KTL2 0.54 1.19 KTL2C 0.65 1.43 Tornado 9. REAR PANEL AND WIRING KT2 - KT2C KTL2 - KTL2C Ver. 2.8 1 1. 4-pin audio input connector 2. 4-pin light controller connector 1 2 2- 2+ 1- 1+ - + AMPLIFIER 32 Wiring 2- to (-)pin of the Amp 2+ bridged to 1(-) 1- bridged to 2(+) 1+ to (+)pin of the Amp the 32 configuration must be used with a KA14, KA24, KA84, KA7, KA7-7, KA10 or a KA10-10 amplifier R G B V+ LIGHT CONTROLLER Light Controller Wiring R to negative DC power for Red LED G to negative DC power for Green LED B to negative DC power for Blue LED V+ Common positive DC power (24V) for RGB LEDs 2- 2+ 1- 1+ 8 Wiring 2- / 1- parallel to (-)pin of the Amp 2+ / 1+ parallel to (+)pin of the Amp - + AMPLIFIER 7 the 8 configuration must be used with a KA1-1 amplifier Warning Take care, respect the polarity and the maximum DC voltage. An inverted polarity or a different voltage could damage the device or part of its component parts. Tornado 9.1 70V VERSION Ver. 2.8 All Tornados are available also in the 70V version: KT2-HV, KT2C-HV, KTL2-HV, KTL2C-HV. The very high impedance of the speakers allows to drive up to 100 units by a single KA84 amplifier channel and up to 50 units by two bridged KA24 amplifier channels. KA24 70V Version Wiring with KA24 2- 2+ 1- 1+ 2- not connected 2+ not connected 1- to 1- pin of the Amp 1+ to 2+ pin of the Amp KA84 70V Version Wiring with KA84 2- 2+ 1- 1+ 2- not connected 2+ not connected 1- to 1- pin of the Amp 1+ to 1+ pin of the Amp 12+ 1+ 2- KA24 (Bridge Mode) Up to 50 units per KA24 in bridge mode (so a total of max 100 units per KA24) 12+ 1+ 2- KA84 Up to 100 units per KA84 channel (so a total of max 400 units per KA84) 2+ and 2- not connected Amplifier 8 Tornado 10. INSTALLATION KT2 - KTL2 Ver. 2.8 3) 4) 5) 6) 6 mm 0.24" KT2C - KTL2C plaster board or ceiling tile 105 mm 4.13" 2) 1) 9 Tornado 11. ACCESSORIES Ver. 2.8 DID YOU KNOW THAT .... Designed as passive speaker, the new Tornados can be easily converted into self-powered devices by inserting the KA1-T2H amplifier module. KA1-T2H Amplifier module for Tornados (32 W) K-AL15 K-AL66 K-AL75 K-AL120 K-AL240 K-CTRL 15 W power supply for 1 KA1-T2H (in background music or speech applications) 66 W power supply for up to 2 KA1-T2H (full power) or up to 4 KA1-T2H (in background music or speech applications) 75 W DIN rail power supply for up to 3 KA1-T2H (full power) or up to 6 KA1-T2H (in background music or speech applications) 120 W DIN rail power supply for up to 5 KA1-T2H (full power) or up to 10 KA1-T2H (in background music or speech applications) and for K-RGBDMX / KRGBREM RGB LED controller for KTL2 and KTL2C 240 W DIN rail power supply for up to 12 KA1-T2H (full power) or up to 24 KA1-T2H (in background music or speech applications) and for K-RGBDMX / KRGBREM RGB LED controller for KTL2 and KTL2C 60 W RGB LED DMX Controller for up to 4 KTL2s or KTL2Cs K-RGBDMX RGB LED DMX Controller for up to 10 KTL2s / KTL2Cs (using the K-AL120) or up to 20 (using the K-AL240) K-RGBREM RGB LED Controller with remote control for up to 10 KTL2s / KTL2Cs (using the K-AL120) or up to 20 (using the K-AL240) KA-FRAME 2U Rack Adapter for 4 K-CTRLs 10 Tornado 11.1 KA1-T2H WIRING 2- 2+ 1- 1+ R G B V+ Ver. 2.8 11 Tornado 12. SERVICE Ver. 2.8 To obtain service: 1) Contact the official K-array distributor in your country. Your local distributor will direct you to the appropriate service center. 2) If you are calling for service, please have the serial number(s) of the unit(s) available for reference. Ask for Customer Service, and be prepared to describe the problem clearly and completely. 3) If the problem cannot be resolved over the phone, you may be required to send the unit in for service. In this instance, you will be provided with an RA (Return Authorization) number which should be included on all shipping documents and correspondence regarding the repair. Shipping charges are the responsibility of the purchaser. Any attempt to modify or replace components of the device will invalidate your warranty. Service must be performed by an authorized K-array service center. Cleaning: Use only a soft, dry cloth to clean the housing. Do not use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia, or abrasives. Do not use any sprays near the product or allow liquids to spill into any openings. 12 Tornado 13. SPECIFICATIONS KT2 - KT2C - KT2-HV - KT2C-HV Power handling Frequency range Impedance Maximum SPL Horizontal Vertical Type Frequency ACOUSTICS 18 W (AES) 150 Hz 18 kHz (-10dB) (1) KT2, KT2H: 8 / 32 (selectable) KT2-HV, KT2C-HV: High Impedance for 70V amp 101 dB (cont.) 107 dB (peak) (2) COVERAGE 90° 90° CROSSOVER External Crossover required 150 Hz, 24 dB/oct suggested minimum Notes for data Full range TRANSDUCERS 2" Neodymium magnet woofer with 2 x 0.8" voice coils POWER AUDIO INPUT Connector 4-pin Phoenix RECOMMENDED AMPLIFIERS Type KA1-T2H, KA14, KA24, KA84 CERTIFICATION IP 54 PHYSICAL KT2 KT2C 74 mm x 123 mm x 118 mm 125 mm x 125 mm x 119 mm Dimensions (2.9" x 4.8" x 4.6") (4.9" x 4.9" x 4.7") Weight 0.56 kg (1.23 lbs) 0.67 kg (1.48 lbs) 1. With dedicated preset; 2. Measured with musical signal New materials and design are introduced into existing products without previous notice. Present systems may differ in some respects from those presented in this datasheet. Ver. 2.8 KTL2 - KTL2C - KTL2-HV - KTL2C-HV Power handling Frequency range Impedance Maximum SPL Horizontal Vertical Type Frequency Full range Connector ACOUSTICS 18 W (AES) 150 Hz 18 kHz (-10dB) (1) KT2, KT2H: 8 / 32 (selectable) KT2-HV, KT2C-HV: High Impedance for 70V amp 101 dB (cont.) 107 dB (peak) (2) COVERAGE 90° 90° CROSSOVER External Crossover required 150 Hz, 24 dB/oct suggested minimum TRANSDUCERS 2" Neodymium magnet woofer with 2 x 0.8" voice coils POWER AUDIO INPUT 4-pin Phoenix RECOMMENDED AMPLIFIERS Type KA1-T2H, KA14, KA24, KA84 LED Type 7 x RGB LED Connector 4-pin Phoenix Light Output Black version: 330 lumen White version: 400 lumen Viewing Angle 90° Consumption 10 W CERTIFICATION IP 40 PHYSICAL KTL2 KTL2C Dimensions 74 mm x 123 mm x 118 mm 125 mm x 125 mm x 119 mm (2.9" x 4.8" x 4.6") (4.9" x 4.9" x 4.7") Weight 0.54 kg (1.2 lbs) 0.59 kg (1.3 lbs) Notes for data 1. With dedicated preset; 2. Measured with musical signal New materials and design are introduced into existing products without previous notice. Present systems may differ in some respects from those presented in this datasheet. 13 Tornado KA1-T2H ACCESSORY DesigneD as passive speakers, the new tornaDos can be easily converteD into self-powereD Devices by inserting the ka1-t2h 12v/24v amplifier moDule. Ver. 2.8 Connectors Wiring Connectors Wiring Type Nominal Power Output Protections Frequency response THD+N 1kHz,1 W AUDIO INPUT Phoenix connector IN (-) IN + (+) GRD (Ground) POWER INPUT Phoenix connector VCC (+) GND (common) AMPLIFIER 1 Module Class D Electronically Processed 32 W @ 8 1% THD + NOISE (1 ) Dynamic limiter, over current, over temperature, short circuit power supply polarity inversion 20Hz 20kHz (+/- 3 dB) for 1W @ 8 0,100% DC POWER Nominal voltage 12/24 Vdc Operating range 10 - 26 Vdc I. Nom. Efficiency 0.4 A / 24 Vdc CONSUMPTION 83% Nominal power Dimensions Weight 10 W PHYSICAL 35 mm x 40 mm x 14 mm (1,37" x 1,57" x 0,55 ") 40 g (0.08 lb) Notes for data 1. EIAJ Test Standard, 1 kHz, 1%THD New materials and design are introduced into existing products without previous notice. Present systems may differ in some respects from those presented in this datasheet. 14 Tornado 14. KT2 AND KT2C EN54-24 DATA Ver. 2.8 KT2 and KT2C are EN54-24 compliant. Consider the specifications below when either model is used in a voice alarm system. KT2 - KT2C Power handling SPL 1W/1m Maximum SPL Connector IN Vmax In (Pink Noise) Frequency Range Coverage Horizontal Coverage Vertcal 15 W 89 dB 100 dB Voice coil A: 1+ 1Voice coil B: 2+ 2Double coil: 1+ 2- (1- 2+ CC) 8.20 V @ 8 Ohm 16.40 V @ 32 Ohm 150 Hz - 18 kHz 180° @ 500 Hz 180° @ 1000 Hz 180° @ 2000 Hz 120° @ 4000 Hz 180° @ 500 Hz 180° @ 1000 Hz 180° @ 2000 Hz 120° @ 4000 Hz K-array 0068-CPR-082 /2017 EN 54-24 : 2008 Loudspeaker for voice alrm systems for fire detection and fire alarms systems for buildings KT2 TYPE B K-array 0068-CPR-082 /2017 EN 54-24 : 2008 Loudspeaker for voice alrm systems for fire detection and fire alarms systems for buildings KT2C TYPE B The contents of this manual are furnished for informational purposes only. K-array s.u.r.l. assumes no responsibility for any errors or inaccuracies that may appear in this manual. K-array s.u.r.l. reserves the right to make modifications without prior notice. 15Adobe PDF Library 16.0 Adobe InDesign 16.4 (Windows)