Narva EX2-R LED Driving Lights

Important Safety Information

• Remove the negative battery cable before installation.
• Ensure lamps are fitted using the appropriate wiring harness or an equivalent auxiliary wiring system.
• Mount lamps securely to a solid surface on the vehicle or bullbar.
• Cables connected to the lamp must not be subjected to wear or other damage.
• Driving lights must dip with High Beam to meet ADR requirements.
• Refer to your local State Government for specific wiring requirements, as they can differ.
• Consult a qualified Auto Electrician to adapt to your vehicle wiring.

Assembly

Each lamp is pre-assembled with stainless steel fasteners.

Mounting: Choose a solid surface on the vehicle or bullbar to mount the driving lights. Secure the lamps using the flat washer, spring washer, and M10 nut.

Lens Protector Removal

Remove the Lens Protector by un-clipping the side wings.

Decal Application

Peel off the adhesive backing of the decal and align it to the edge of the lens cover's decal outline. Press the decal down firmly and push out any bubbles. Avoid washing the lens cover after application.

Colour Trim Replacement

1. Remove the Colour Trim by unclipping it from the edge of the lamp.
2. Change the Colour Trim and reassemble in reverse order.

Angle Adjustment

Loosen the nut and adjust the lamp to the desired angle. Re-tighten the nut.

Wiring Instructions

EX2-R Wiring Without Switch

1. Join both positive red leads from the driving lights. Crimp the ends together using cable sized as per the table below.
2. Terminate the cable to one end of the fuse holder and the other end to the positive terminal of the battery.
3. Join both negative black leads from the driving lights. Crimp the ends together using cable sized as per the table below.
4. Terminate to the negative terminal of the battery or vehicle ground chassis.
5. Join the yellow high beam trigger wire to a 3 mm wire and connect it to the high beam feed wire of the vehicle. For Negative switching, refer to the relevant diagram.
6. Ensure the fuse and negative battery cable are connected.

Test the driving lights by turning the high beams on.

EX2-R Wiring With Switch

1. Join both positive red leads from the driving lights. Solder or crimp the ends together using cable sized as per the table below.
2. Terminate the cable to one end of the fuse holder and the other end to the positive terminal of the battery.
3. Join both negative black leads from the driving lights. Crimp the ends together using cable sized as per the table below.
4. Terminate to the negative terminal of the battery or vehicle ground chassis.
5. Join the yellow high beam trigger wire to a 3 mm wire and connect it to the switch in the cabin. Connect a 3 mm wire from the switch to the high beam output of the vehicle.
6. Ensure the fuse and negative battery cable are connected.

Test the driving lights by turning the high beams and switch on.

White Position Light Wiring

ADR approved white position lights can be used without the EX2-R Bluetooth module. Connect the supplied round 5-pin female connector flying lead with a brown wire to the round 5-pin male connector from the EX2-R driving lights. Connect the brown wire using 2.5 mm wire to an ignition source or parking lights.

Test the white position lights by turning on the parking lights or ignition.

EX2-R Bluetooth Module Wiring (P/No. 74426)

1. Connect the round 5-pin female connector from the controller to the round 5-pin male connector from the EX2R driving light. Ensure the weatherproof 5-pin connectors are securely fastened and route cables away from the engine. The connectors are directional; ensure correct positioning and fasten each end cap.
2. Connect the red positive fused power lead to an ignition source or parking lights. Do not connect directly to the battery, as this will keep the position lights and Bluetooth on at all times.
3. Connect the black negative power lead to the vehicle ground chassis or battery negative terminal. Refer to the EX2 Bluetooth module instructions for usage.

Recommended Cable Sizes and Fuses

Cable Lengths:

• EX2-R (P/no 72143, 72163, 72173 and 72183) Driving lights come with a 2000mm power flying lead and a 1000mm RGB cable.
• EX2-R (P/no 72174 and 72184) Driving lights come with a 500mm power lead + 3PIN DT + 1500mm fused power lead harness and a 1000mm RGB cable.

Lamp Wiring (With Switch) Diagram Description

The diagram illustrates the wiring for EX2-R driving lights with a switch. It shows the connection of the driving lights to the vehicle's high beam feed, battery, and an ignition source or parking light output via a fuse. It also indicates the connection to an RGBW module. No relay is required due to internal switching technology.

Lamp Wiring (Without Switch) Diagram Description

The diagram illustrates the wiring for EX2-R driving lights without a switch. It shows the connection of the driving lights to the vehicle's high beam feed, battery, and an ignition source or parking light output via a fuse. It also indicates the connection to an RGBW module. No relay is required due to internal switching technology.

Note: Driving lights must dip with High Beam to meet ADR requirements. Please refer to your local State Government for wiring requirements, as they can differ. Consult a qualified Auto Electrician to adapt to your vehicle wiring.

Technical Specifications

Parts Available

Colour Trims

Spare Parts

Wiring for Negative Switched Vehicles

This section is for negative switched vehicles only.

1. Using a 4PIN normally open relay (Narva P/no 68000), connect PIN 30 and PIN 85 to a constant +12V source with a 5 AMP inline fuse.
2. Connect the negative (-) high beam wire from the vehicle to Pin 86.
3. Connect Pin 87 to the EX2 High beam feed wire.

Diagram Description: The diagram shows the wiring connections for a negative switched vehicle using a 4-pin normally open relay. It details the connections to the vehicle's high beam feed, battery, and the relay pins.

Caution: Please consult a qualified Auto Electrician to adapt to your vehicle wiring, as incorrect connections can cause damage to your vehicle wiring and electronic modules.

Warranty

Applicable only to products sold in Australia.

Brown & Watson International Pty Ltd (BWI) warrants that its products will be free from failures in material and workmanship for a period of one (1) year from the date of original purchase by the consumer, unless otherwise indicated. This warranty excludes ordinary wear and tear, abuse, alteration of products, or damage caused by the consumer. Bulbs and lenses are specifically excluded.

To make a warranty claim, the consumer must deliver the product at their own cost to the original place of purchase or a nominated location for assessment, along with the original invoice and a written explanation of the claim.

BWI reserves the right to repair or replace products with minor failures. For major failures, the consumer is entitled to a replacement or refund, plus compensation for reasonably foreseeable loss or damage.

This warranty is in addition to other rights and remedies available under State or Federal legislation.

Important Note: Narva products come with guarantees that cannot be excluded under the Australian Consumer Law. Consumers are entitled to a replacement or refund for a major failure and compensation for other reasonably foreseeable loss or damage. Goods failing to be of acceptable quality, but not amounting to a major failure, are entitled to repair or replacement.

Distributed by:
Brown & Watson Int. Pty. Ltd.
Knoxfield, Victoria 3180
PH: 1800422422

www.narva.com.au

Document Issue: IS521, Version 1: 30.01.23