nJoy Keen Series User Manual

Introduction

Thank you for purchasing our products! Please read this manual before using the product.

nJoy is a brand of power and backup protection products that create solutions for multiple levels of environment complexity, from residential to industrial. This UPS will protect your electronic equipment from physical damage and will provide emergency battery backup power to prevent data loss in the event of power problems.

Models Covered:

• Keen 600 / Keen 600 USB
• Keen 800 / Keen 800 USB
• Keen 1000 / Keen 1000 USB
• Keen 1500 / Keen 1500 USB
• Keen 2000 / Keen 2000 USB

Model Numbers: UPLI-LI060KE-CG01B, UPLI-LI060KU-CG01B, UPLI-LI080KE-CG01B, UPLI-LI080KU-CG01B, UPLI-LI100KE-CG01B, UPLI-LI100KU-CG01B, UPLI-LI150KE-CG01B, UPLI-LI150KU-CG01B, UPLI-LI200KE-CG01B, UPLI-LI200KU-CG01B.

Document Reference: 949.34.22.1

Before using this product, carefully read all product documentation and retain it for future reference.

1. Package Contents

• ✓ UPS unit
• ✓ Power cord (attached)
• ✓ User manual
• ✓ Warranty card
• ✓ USB cable (only for models with HID USB communication port)

2. Product Overview

Keen 600/800 Series - Front and Back Views

Front View: Features a central geometric design, a power button (labeled 1), and LED indicators (labeled 2). The nJoy logo is visible at the bottom.

Back View: Shows two AC outlets (labeled 4), a USB communication port (labeled 9), and RJ11/RJ45 surge protection ports (labeled 10). The input power cord (labeled 3) is also shown.

Keen 1000/1500/2000 Series - Front and Back Views

Front View: Displays a geometric pattern, a Power On/Off Button (labeled 1), LED indicators (labeled 2), AC Mode LED (labeled 5), Battery Mode LED (labeled 6), and Fault LED (labeled 7). The nJoy logo is at the bottom.

Back View: Includes four AC outlets (labeled 4), an Input Circuit Breaker (labeled 8), a HID USB communication port (labeled 9), and RJ11/RJ45 surge protection ports (labeled 10). The input power cord (labeled 3) is also visible.

NOTE! The HID USB communication port and RJ11/RJ45 surge protection port are only available for Keen 600 USB, Keen 800 USB, Keen 1000 USB, Keen 1500 USB, and Keen 2000 USB models.

3. Important Safety Warnings

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

• To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (Refer to specifications for acceptable temperature and humidity range.)
• To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing it near heat emitting appliances such as space heaters or furnaces.
• Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to the UPS.
• Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.
• In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.
• Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
• Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized personnel away from batteries.

4. Installing Your UPS System

4.1 Hardware Installation Guide

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8 hours is recommended to ensure maximum charge capacity. Charge loss may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into an AC outlet. The unit will charge in both the ON and OFF positions.
2. With the UPS unit off and unplugged, connect your computer, monitor, and any externally powered data storage device (e.g., Zip drive, Jazz drive, Tape drive) into the battery power supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder, or other large electrical device into the battery power supplied outlets, as their power demands can overload and possibly damage the unit.
3. Plug the UPS into a 2-pole, 3-wire grounded receptacle (wall outlet). Ensure the wall branch outlet is protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g., air conditioner, refrigerator, copier). Avoid using extension cords.
4. Press the power switch to turn the unit on. The power-on indicator light will illuminate, and the unit will emit a "beep".
5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off, unplug at least one piece of equipment from the battery power supplied outlets, wait 10 seconds, ensure the circuit breaker/fuse is normal, and then turn the UPS on.
6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.
7. To store your UPS for an extended period, cover it and store it with the battery fully charged. Recharge the battery every three months to ensure battery life.

4.2 Software Installation Guide

For optimal computer system protection, install the UPS monitoring software from: http://www.powermonitor.software/ to fully configure UPS shutdown.

4.3 Positioning

For optimal ventilation of the UPS, please place it at least 15cm distance from any wall or object. This ensures adequate airflow around the unit.

5. LED Indication and Alarm

6. Troubleshooting

Disposal of Old Electrical & Electronic Equipment

[WEEE symbol] (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.

EU Declaration of Conformity

We, manufacturer/importer:

DAI-TECH SA
Str. Berlin, Nr 6, C.P. 307160,
Dumbrăvița, Timiș, România

declare that the products UPS Keen Series, including models:

UPLI-LI060KE-CG01B, UPLI-LI080KE-CG01B, UPLI-LI100KE-CG01B, UPLI-LI150KE-CG01B, UPLI-LI200KE-CG01B, UPLI-LI060KU-CG01B, UPLI-LI080KU-CG01B, UPLI-LI100KU-CG01B, UPLI-LI150KU-CG01B, UPLI-LI200KU-CG01B

are in conformity with:

[CE Mark] (EC conformity marking)

Tested with the listed standards, the above-mentioned products were found in compliance with Directive 2015/863, Directive 2014/30/EC (EMC), and Directive 2014/35/EC (LVD).

Standards Compliance:

• EN 50581: 2012
• EN 62321: 2009
• EN 62040-2: 2006
• EN 61000-3-2: 2014
• EN 61000-3-3: 2013
• EN 61000-4-2:2009
• EN 61000-4-3:2006 +A1: 2008 +A2:2010
• EN 61000-4-4: 2012
• EN 61000-4-5:2014
• EN 61000-4-6:2014
• EN 61000-4-8:2010
• EN 61000-4-11: 2004
• EN 61000-2-2:2002
• IEC 62040-1: 2008 (First Edition) + Am 1:2013

and in conformity with:

[RoHS] (RoHS conformity marking) in accordance with European Directive 2011/65/EU.

Declaration Details:

Stamp: DAI-TECH SA, ROMANIA

Date and location: Aug. 01, 2022, Timișoara

Signature and name: Tommy Lee