Westfalia Tow Bar Installation Guide

General Information & Specifications

Article Number: 13.0607

Series Number: 13.8607 - 320071600001

Homologation: e4*94/20*4294*00

Class and Type of Hitch: F

D-Value: 10.20 kN

Max Vertical Load (S): 80 kg

Towing Capacity: Refer to vehicle's registration document.

Safety and General Guidelines

Adherence to national guidelines concerning official approval of auxiliaries must be observed.

Any alteration or conversion of the tow bar is prohibited and will result in the cancellation of the type approval.

Remove insulating compound or underbody coating from the vehicle's contact surfaces before installation.

The tow bar is intended for towing trailers and carrying loads; any other use is prohibited.

Parking Sensor Interference: Vehicles equipped with parking assistance systems may experience malfunctions if tow bar components are within the sensor's detection range. Adjust the sensing range or disable the parking assistance system if necessary. This is less likely with removable or pivoting ball hitches when the ball is not in the operating position.

The tow bar is a safety component and must only be installed by qualified technicians. Improper installation can lead to serious accidents!

The Swedish text in the original manual is binding.

Subject to change.

Component Identification

The following components are included:

• A: FBAD 12155 (1x)
• B: (Component details not fully specified, value 53.47) (1x)
• C: M14 x 40 (8.8) bolts (2x)
• D: M12 lock nuts (8) (2x)
• E: Washers (13x24x2) (1x)
• Additional hardware includes M14x35x3 washers (4x) and M14 bolts (4x).

Installation Steps

Step 01: Access Mounting Points

Remove rear trim panels and any underbody protection near the mounting locations. [➡️]

Step 02: Remove Rear Bumper

Carefully remove the rear bumper of the vehicle. [⬇️]

Step 03: Vehicle Ready for Installation

The vehicle is now prepared for the tow bar installation.

Step 04: Position Tow Bar Frame

Position the main tow bar frame onto the vehicle's chassis mounting points. [⬇️]

Step 05: Loosely Attach Frame

Secure the tow bar frame loosely using the provided bolts and nuts. [?]

Step 06: Attach Additional Brackets

Attach any additional brackets or supports as indicated in the diagrams. [⬇️]

Step 07: Prepare Chassis Cut-outs

Prepare necessary cut-outs in the vehicle's underbody or chassis to accommodate the tow bar. [➡️]

Step 08: Position Complete Assembly

Carefully position the complete tow bar assembly into its final mounting location. [⬆️]

Step 09: Install M14 Bolts

Install and loosely tighten the M14x40 bolts (2x) with washers and nuts. [?]

Step 10: Torque M14 Bolts

Torque the M14 bolts to 132 Nm. [? ➡️ 132 Nm]

Step 11 & 12: Bumper Cut-out Dimensions (Facelift Models)

For Volvo S/V60 Facelift (2013-) models, specific bumper cut-out dimensions are required:

• Cut-out depth: 40mm (as per Step 11 diagram) or 60mm (as per Step 12 diagram).
• Positioning: R30 radius, C/C 125mm, 30mm offset from center.

Step 13: Attach Ball Hitch Assembly

Attach the detachable ball hitch assembly to the tow bar frame. Torque the M12 lock nuts to 83 Nm. [? ➡️ 83 Nm]

Technical Checks and Requirements

Clearance Requirements:

Ensure free space according to Appendix VII, Diagram 30 of Directive 94/20/EG. Key dimensions include:

• Minimum clearance values: e.g., 32mm, 55mm, 75mm.
• Maximum clearance values: e.g., 100mm, 45°, 30°.
• Specific measurements: R30, R14.5, R40.
• Longitudinal dimension: 350 - 420 mm.

Vehicle Weight Limits: Adhere to the vehicle's permissible total weight.

Initial Checks: Perform an initial inspection at 0 km. [? 0km]

Follow-up Checks: Perform a follow-up inspection at 1000 km. [? 1000km]

Estimated Installation Time: 90 minutes. [⏰ 90 Min]

Declaration of Correct Installation

The undersigned company declares that the tow bar type 13.0607 has been installed correctly, respecting attachment points and specifications provided by the manufacturer, on the vehicle [Vehicle Model/VIN] registered [License Plate].

The user has also been informed about the USE and MAINTENANCE of the device.

[Signature/Stamp Area]