Business Community
Festa Cloud
CE Regulatory Compliance | TP-LinkTP-Link Product Support - Wireless Networking Equipment SupportDownload Center | TP-LinkRegulatory Compliance | TP-Link
Installation Guide for tp-link models including: F52, F52 Indoor and Outdoor Access Point, Indoor and Outdoor Access Point, Outdoor Access Point, Access Point, Point
Download for Festa F52-Outdoor | TP-Link Australia
Download für Festa F52-Outdoor | TP-Link Deutschland
7 июн. 2024 г. — Step 1: Remove the mounting bracket from the passive PoE Adapter. Drill two holes on the wall and insert the plastic wall anchors into the holes.
File Info : application/pdf, 2 Pages, 581.63KB
DocumentDocument1 Overview Package Contents Panel Layout Quick Installation Guide Indoor/Outdoor Access Point AP Mounting Bracket (for AP) Passive PoE Adapter (Mounting Bracket Included) Quick Installation Guide Indoor/Outdoor Access Point Note: Festa F52-Outdoor is used as an example throughout the Guide. Images may differ from your actual product. ©2024 TP-Link 7106511102 REV1.0.0 Installation Guide Self-tapping Screws (for Passive PoE Adapter) Note: Festa F52-Outdoor is used as an example throughout the Guide. Images may differ from your actual product. ©2024 TP-Link 7106511102 REV1.0.0 Antennas Plastic Wall Anchors Self-tapping Screws Power Cord Waterproof Rubber Insert Note: Accessories may vary by product. Pole Mounting Strap Shielded Ethernet Port LAN RESET SYS LED Explanation LED Status Flashes green twice Solid green Flashing yellow Flashing yellow, green Quickly flashing yellow, green Flashing green slowly (Only for Festa F52-Outdoor) Indication Initialization is completed. The device is initializing or working properly. System errors. RAM, Flash, Ethernet, WLAN or firmware may be malfunctioning. Firmware update is in progress. Do not disconnect or power off the device. The device is being reset to its factory default settings. The device is in an isolated state. Passive PoE Adapter Remote Reset: Press and hold for about 8 seconds until the LED is quickly flashing yellow then green. The AP will restore to factory default settings. Power LED: On: Power on Off: Power off Note: Festa F52-Outdoor does not support the Remote Reset feature. 2 Lightning and ESD Protection Before mounting the AP, consider Lightning and ESD Protection to ensure safety. Proper grounding is extremely important for outdoor devices. By using a shielded CAT5e (or above) cable for connection, you can reduce the damage of ESD attacks. AP Shielded CAT5e (or above) Cable Grounded PoE Adapter Grounded 3-wire Power Outlet 3 Hardware Installation Mount the AP The AP can be pole-mounted or wall-mounted. Follow the steps below for the appropriate installation. Option 1: Pole Mounting Step 1: Lead the end of the pole mounting strap through the back of the AP. Step 2: Position the AP and wrap the pole mounting strap around the pole. Feed the end through the screw-block and tighten the strap until the AP is secure. Step 3: Connect the antennas to the AP. For optimal Wi-Fi performance, adjust the direction of the antennas. It is recommended to position the antennas at 45-degree angles. 45° 45° Option 2: Wall Mounting Step 1: Place the mounting bracket (for AP) in the right position. Mark two positions for the screw holes. Drill two holes for the screws at the marked positions. Step 2: Insert the plastic wall anchors into the holes. Align the bracket (for AP) to the plastic wall anchors and drive the self-tapping screws into the anchors through the bracket (for AP). Step 3: Align the mounting tabs on the back of the AP with the slot of the mounting bracket (for AP). Push and slide the AP downward until it locks into place. Step 4: Connect the antennas to the AP. For optimal Wi-Fi performance, adjust the direction of the antennas. It is recommended to position the antennas at 45-degree angles. 7.6 mm (19/64 in) 45° 45° Connect Cables Step 1: Firmly grasp the rear of the interface cover and pull it downward. Step 2: Use an adequate Ethernet cable to connect the LAN port. The length of cable is up to 100 m for steady power supply. Shielded CAT5e (or above) cable is recommended. Step 3: Attach the waterproof rubber insert to the groove at the underside of the device for waterproofing. Move the Ethernet cable to the hole of the waterproof rubber insert. Step 4: Flatten the waterproof rubber insert until it gets parallel to the device. Replace the cover until it firmly locks into place. Power On The AP can be powered via the passive PoE adapter or a PSE device (such as a PoE switch) which complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) of IEC 62368-1. Option 1: Via Passive PoE Adapter Connecting the PoE Adapter Connect the AP to a Power over Ethernet (PoE) adapter as follows: Step 1: Remove the mounting bracket from the passive PoE Adapter. Drill two holes on the wall and insert the plastic wall anchors into the holes. Secure the mounting bracket to the wall. Make sure the shoulders at the corners of the mounting bracket are on the outside and pointing upward. Step 2: Attach the passive PoE adapter to the mounting bracket (for PoE Adapter) by sliding the adapter in the direction of the arrows until it locks into place. Ethernet cable PoE LAN length up to 100 m Option 2: Via PoE Switch Note: Festa F41-Outdoor does not support this power option. Connect an Ethernet cable from the PoE switch to the Ethernet port. Mounting the PoE Adapter (Optional) Note: To ensure the passive PoE adapter is attached most securely, it is recommended to install the adapter with the Ethernet port facing upward. PoE Switch 4 Software Configuration You can configure and manage Festa APs via the Festa Cloud-Based Controller. Festa Cloud Router / Gateway Switch AP AP AP AP Clients Option 1: Via Web Browser 1. Make sure that your management device can access the internet. 2. Launch a web browser and enter https://festa.tplinkcloud.com in the address bar. Log in with your TP-Link ID. https://festa.tplinkcloud.com 3. Click + Add Controller, then you will see you have successfully registered for a Cloud-Based Controller and the controller has been added to the controller list. 4. Click Set Up Now, click Config New Setup, and follow the step-by-step instructions to complete the configuration wizard of the controller. 5. On the controller's management page, go to Devices, click + Add Devices, and follow the step-by-step instructions to adopt Festa devices. Now you can configure and manage Festa devices on the controller. Option 2: Via Festa App 1. Download and install the Festa App from App Store or Google Play. or Scan for Festa App Festa App 2. Launch the Festa App and log in with your TP-Link ID. 3. Tap + on the upper right corner, then you will see you have successfully registered for a Cloud-Based Controller and the controller has been added to the controller list. 4. Tap Confirm, tap Let's Get Started, and follow the step-by-step instructions to complete the configuration wizard of the controller. 5. On the controller's management page, go to Devices, click + on the upper right corner, and follow the step-by-step instructions to adopt Festa devices. Now you can configure and manage Festa devices via the Festa App. For detailed configurations, refer to the User Guide of the controller. The guide can be found on the download center of our official website: https://www.tp-link.com/support/download/?type=smb. To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com/business to join TP-Link Community. For technical support, the user guide and other information, please visit https://www.tp-link.com/support/?type=smb, or simply scan the QR code. Safety Information · Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid. · Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. · Do not use the device where wireless devices are not allowed. · Do not use any other chargers than those recommended. · Adapter shall be installed near the equipment and shall be easily accessible. · Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us. · Adapter should be used indoors where the ambient temperature is lower than or equal to 40. · The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible. TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/ TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/ Attention: In EU member states, EFTA countries and Northern Ireland, the operation in the frequency range 5150MHz-5350MHz is only permitted indoors. Attention: In Great Britain, the operation in the frequency range 5150MHz - 5350MHz is only permitted indoors. For Festa Controller, go to the Devices page and select the desired AP to specify the channel. For web browser, go to Wireless > Wireless Settings to specify the channel. AT BE BG CH CY CZ DE DK EE EL ES FI FR HR HU IE UK IS IT LI LT LU LV MT NL NO PL PT RO SE SI SK UK(NI)