SHARP XL-HF203B Hi Fi Component System

For Users in U.S.

CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Explanation of Graphical Symbols:

• ⚡️ Lightning Flash with Arrowhead Symbol: Within an equilateral triangle, intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• ❗ Exclamation Point Symbol: Within an equilateral triangle, intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This product is classified as a CLASS 1 LASER PRODUCT.

Caution: Use of any controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure.

General Notes

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC Radiation Exposure Statement: This device complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. It must not be co-located or operating in conjunction with any other antenna or transmitter. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and person's body.

Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

FOR YOUR RECORDS: For your assistance in reporting this unit in case of loss or theft, please record below the model number and serial number which are located on the rear of the unit. Please retain this information.

• Model number: XL-HF203B
• Serial number: ..............................
• Date of purchase: ..............................
• Place of purchase: ..............................

Supply of this product does not convey a license nor imply any right to distribute content created with this product in revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue-generating streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for such use is required. For details, please visit http://mp3licensing.com

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

Important Safety Instructions

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of this product, please read the following precautions carefully before use.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Additional Safety Information

15. Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For product intended to operate from battery power, or other sources, refer to the operating instructions.
16. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

To prevent fire or shock hazard, do not expose this appliance to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.

18. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
    • a. When the AC cord or plug is damaged,
    • b. If liquid has been spilled, or objects have fallen into the product,
    • c. If the product has been exposed to rain or water,
    • d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,
    • e. If the product has been dropped or damaged in any way, and
    • f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts: When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
21. Wall or ceiling mounting: When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.
22. Power Lines: An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
23. Protective Attachment Plug: The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug.
24. Stand: Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the manufacturer.

Consumer Limited Warranty (For U.S. customer only)

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.

In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.

TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP

SHARP ELECTRONICS CORPORATION
1 Sharp Plaza, Suite 1, Mahwah, NJ 07495-1123

Special Notes

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and trade names are those of their respective owners.

The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.

• XL-HF203B Hi Fi Component System consisting of XL-HF203B (main unit) and CP-HF203 (speaker system).

Precautions

General

• Keep your equipment at least 4" (10 cm) of free space along the sides, top and back for proper ventilation. (Diagram description: Shows a diagram illustrating 4 inches (10 cm) of clearance around the unit on the sides and top, and 0 inches (0 cm) at the front.)
• Use the unit on a firm, level surface free from vibration.
• Place the speakers at least 12" (30 cm) away from any CRT TV to avoid color variations across the TV screen. If the variations persist, move the speakers further away from the TV. LCD TV is not prone to such variation.
• Keep the unit away from direct sunlight, strong magnetic fields, excessive dust, humidity and electronic / electrical equipment (home computers, facsimiles, etc.) which generate electrical noise.
• Do not expose the unit to moisture, to temperatures higher than 140°F (60°C) or to extremely low temperatures.
• If the unit does not work properly, unplug and plug it in again. Then turn on the unit.
• In case of an electrical storm, unplug the unit for safety.
• Hold the AC power plug by the head when removing it from the AC outlet, as pulling the cord can damage internal wires.
• Do not place anything on top of the unit.
• The AC power plug is used as a disconnect device and shall always remain readily operable.
• Do not remove the outer cover, as this may result in electric shock. Refer internal service to your local SHARP service facility.
• This unit should only be used within the range of 41°F - 95°F (5°C - 35°C).

Warning: The voltage used must be the same as that specified on this unit. Using a higher voltage is dangerous and may result in a fire or other type of accident causing damage. SHARP will not be held responsible for any damage resulting from such usage.

Volume control

The sound level at a given volume setting depends on speaker efficiency, location and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on with the volume control setting up high, or while continually listening at high volumes. Excessive sound pressure from earphones and headphones can cause hearing loss.

Controls and Indicators

Front panel

(Diagram description: Shows the front panel of the main unit with numbered controls.)

1. Remote sensor
2. Timer indicator
3. Disc Tray
4. Volume Control
5. ON/STANDBY Button
6. FUNCTION Button
7. USB Terminal
8. Audio In Jack
9. Headphone Jack
10. Pairing Button
11. Tuner Preset Down, CD/USB Skip Down Button
12. Tuner Preset Up, CD/USB Skip Up Button
13. Disc/USB/Bluetooth Stop Button
14. Disc/USB/Bluetooth Play or Pause Button
15. Disc Tray Open/Close Button

Remote control

(Diagram description: Shows the remote control with numbered buttons.)

1. Remote Control Transmitter
2. On/Standby Button
3. Headphone Link Button
4. USB Stop Button
5. Tuner/Band Button
6. Timer Button
7. Input Button
8. Display Button
9. Tuner Preset Up Button
10. Folder Button
11. Tuning Down, Skip Down, Fast Reverse, Time Down Button
12. X-Bass Button
13. Tuner Preset Down Button
14. Treble Button
15. Clear Button
16. Bass Button
17. Open/Close Button
18. CD Stop Button
19. CD Play / Pause Button
20. USB Play / Pause Button
21. Eco Button
22. Clock Button
23. Sleep Button
24. Play Mode Button
25. Tuning Up, Skip Up, Fast Forward, Time Up Button
26. Enter Button
27. Mute Button
28. Memory Button
29. Volume Up Button
30. Volume Down Button
31. Dimmer Button
32. Bluetooth Play / Pause Button
33. Bluetooth Pairing Button
34. N-Mark (NFC detection area)

Display Indicators

(Diagram description: Shows the display panel with numbered indicators.)

1. USB Indicator
2. CD Indicator
3. MP3 Indicator
4. WMA Indicator
5. RDM (Random) Indicator
6. MEM (Memory) Indicator
7. Repeat Indicator
8. Play/Pause Indicator
9. Tuning FM/Bluetooth status Indicator
10. FM Stereo Mode Indicator
11. Stereo Station Indicator
12. Muting Indicator
13. X-bass Indicator
14. Title Indicator
15. Artist Indicator
16. Folder Indicator
17. Album Indicator
18. File Indicator
19. Track Indicator
20. Daily Timer Indicator
21. Once Timer Indicator
22. Disc Indicator
23. Total Indicator
24. Sleep Indicator

Speaker system

(Diagram description: Shows a diagram of a speaker with numbered parts.)

1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Terminal

System Connections

Make sure to unplug the AC power cord before making any connections.

To select Line In function: Press FUNCTION button (main unit) or AUDIO/LINE (INPUT) button (remote control) repeatedly until Line In is displayed.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

(Diagram description: Illustrates system connections. Shows the rear panel of the unit with labels for SPEAKERS (Left/Right), Subwoofer Pre-out, Headphones, Audio In, Line In, Optical In, PC In, FM antenna, AM antenna. It depicts connections for a TV, PC, portable audio player, AM loop antenna, FM antenna, external FM antenna, commercially available subwoofer, and speakers. It also shows the AC power cord connection.)

Antenna connection

• Supplied FM antenna: Connect to the FM 75 ohms jack and position it where reception is best.
• External FM antenna: Use an external FM antenna (75 ohms coaxial cable) for better reception. Disconnect the supplied FM antenna wire before use.
• Supplied AM loop antenna: Connect to the AM terminal and position it where reception is best. Place it on a shelf, etc., or attach it to a stand or a wall with screws (not supplied).

Installing the AM loop antenna

(Diagram description: Shows two small diagrams: one for assembling the loop antenna, and another showing how to attach it to a wall using screws.)

Note: Keep the antenna away from the unit or AC power cord to avoid noise pickup.

Speaker connection

• Use speakers with an impedance of 4 ohms or more, as lower impedance speakers can damage the unit.

(Diagram description: Shows a close-up of speaker wire connections, indicating red for positive terminal and black for negative terminal.)

(Diagram description: Shows an 'Incorrect' example where bare speaker wires are touching.)

Bluetooth standby mode

The first time the unit is plugged in, it will enter the Bluetooth standby mode. “Bluetooth Stby” will be displayed.

• To cancel the Bluetooth standby mode, press the ECO button (remote control) during power standby mode. The unit will enter the low power consumption mode.
• To return to the Bluetooth standby mode, press the ECO button again.

AC power connection

After all connections have been made correctly, plug the AC power cord into the AC outlet.

Note: Unplug the AC power cord from the AC outlet if the unit will not be in use for a prolonged period of time.

Battery and Remote Control

Battery installation

Use 2 "AAA" size battery (UM/SUM-4, R3, HP-16 or similar). Battery is not included.

1. Open the battery cover.
2. Insert the batteries according to the terminal indicated in the battery compartment. When inserting or removing the batteries, push them toward the (-) battery terminals.
3. Close the cover.

(Diagram description: Shows three steps for battery installation: opening the cover, inserting batteries, and closing the cover.)

Caution:

• Replace all old batteries with new ones at the same time.
• Do not mix old and new batteries.
• Remove the batteries if the unit will not be used for a long period of time. This will prevent potential damage due to battery leakage.
• Do not use rechargeable batteries (nickel-cadmium battery, etc.).
• Installing the batteries incorrectly may cause the unit to malfunction.
• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Notes concerning use:

• Replace the battery if the operating distance is reduced or if the operation becomes erratic. Purchase 2 “AAA” size batteries (UM-4, R3, HP-16 or similar).
• Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth.
• Exposing the sensor on the unit to strong light may interfere with operation. Change the lighting or the direction of the unit.
• Keep the remote control away from moisture, heat, shock and vibrations.

Test of the remote control

The remote control can be used within the range shown below:

(Diagram description: Shows a diagram of the remote control's range, indicating a distance of 8" - 20' (0.2 m - 6 m) from the remote sensor.)

General Controls

To turn the power on

Press the ON/STANDBY button to turn the power on or off.

Display brightness control

Press the DIMMER button (remote control).

• Dimmer 1 (Display is dim).
• Dimmer 2 (Display gets dimmer).
• Dimmer off (Display is bright).

Volume auto fade-in

If you turn off and on the main unit with the volume set to 27 or higher, the volume starts at 16 and fades in to the last set level.

Volume control

Turn the volume knob toward VOLUME +/- (main unit) or press VOL +/- (remote control) to increase or decrease the volume.

Muting

To mute the volume, press the ? button (remote control). Press again to restore the volume.

Direct key power on function

When you press any of the following buttons, the unit turns on.

• CD, USB ▶, BLUETOOTH ▶, INPUT, TUNER (BAND), OPEN/CLOSE (remote control): Selected function is activated.
• ▶ (main unit): The unit turns on and playback of the last function will start (CD, TUNER, USB, AUDIO IN, LINE IN, OPTICAL IN, PC IN, BLUETOOTH)

Auto power off function

The main unit will enter the standby mode after 15 minutes of inactivity during:

• Audio/Line In/Optical In/PC In: No detection of input signal.
• CD: In the stop mode or no disc.
• USB: In the stop mode or no media.
• Bluetooth: No connection after approximately 15 minutes. In the pause or stop mode and no incoming signal from devices after approximately 15 minutes.

X-Bass control

When the power is first turned on, the unit is in the extra bass mode. “X-BASS” indicator appears. To cancel this mode, press the X-BASS button (remote control).

Bass or Treble control

1. Press the BASS or TREBLE button to select "Bass" or "Treble" respectively.
2. Within 5 seconds, press the VOL (+ or –) button to adjust the bass or treble.

Bass: -5 --- 0 --- +5

Treble: -5 --- 0 --- +5

Function

Press the FUNCTION button repeatedly to select desired function.

→ CD → FM STEREO → FM MONO → AM → USB → PC In → Optical In → Line In → Audio In → Bluetooth

Note: The backup function will protect the memorized function mode for a few hours should there be a power failure or the AC power cord becomes disconnected.

Bluetooth and NFC Connectivity

Listening on Android™ devices

Listening to a CD or MP3/WMA disc

(Diagram description: Shows the main unit and remote control with CD playback related buttons highlighted.)

Disc playback

1. Press the ON/STANDBY button to turn the power on.
2. Press the FUNCTION button repeatedly on the main unit to select CD function.
3. Press the OPEN/CLOSE button to open the disc compartment.
4. Place the disc on the disc compartment, label side up.
5. Press the OPEN/CLOSE button to close the disc tray.
6. Press the ▶/II (CD ▶/II) button to start playback.

To stop playback completely: Press the ■ button twice.

Caution:

• Do not place two discs in one-disc-tray.
• Do not play discs of special shapes (heart, octagon, etc). It may cause malfunctions.
• Do not push the disc tray while it is moving.
• If the power fails wait until the power is restored.
• If TV or radio interference occurs during CD operation, move the unit away from the TV or radio.
• Be sure to place 8 cm (3") disc in the middle of the disc tray.
• Due to the structure of the disc information, it takes longer to read an MP3/WMA disc than a normal CD (approximately 20 to 90 seconds).

Note for CD or MP3/WMA disc:

• Rewritable multi-session discs with unfinished writing, can still be played.

To resume playback after stopping (resume play)

You can resume playback from the point playback is stopped.

1. While a disc is playing, press the ■ button once. The system stores the point you stopped.
2. To resume play, press the CD ▶/II button. Playback resumes from the point you stopped.

To cancel the resume playback: Press the ■ button twice.

Note: Depending on the disc, playback may resume from slightly before the stopped position.

Random play

To random play all tracks:

Press PLAY MODE button on the remote control repeatedly until "Random" appears. Press the ▶/II (CD ▶/II) button.

To cancel random play:

Press the PLAY MODE button again. "RDM” indicator will disappear.

(Diagram description: Shows the display indicating 'RDM' and track information.)

Notes:

• If you press the ▶▶ button during random play, you can move to the track selected next by the random operation. However, the ◀◀ button does not allow you to move to the previous track. The beginning of the track being played will be located.
• In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks.)

Listening to a CD or MP3/WMA disc (continued)

Repeat play

Repeat play can play one track, all tracks or a programmed sequence continuously.

• To repeat one track: Select desired track using the ◄ or ▶▶ button. Press the PLAY MODE button repeatedly until “Repeat One” appears. Press the ▶/II (CD ▶/II) button.
• To repeat all tracks: Press the PLAY MODE button repeatedly until “Repeat All” appears. Press the ▶/II (CD ▶/II) button.
• To repeat desired tracks: Perform steps 1 - 5 in "Programmed play" section on this page and then press the PLAY MODE button repeatedly until "Repeat All" appears.
• To repeat one folder: While in Folder mode on (MP3/WMA), press PLAY MODE button repeatedly until “Repeat Folder” appears. Press the ▶/II (CD/II) button.

To cancel repeat play: Press the PLAY MODE button repeatedly until “Normal” appears and "" disappears.

(Diagram description: Shows CD playback with repeat indicators.)

Caution: After performing repeat play, be sure to press the ■ button. Otherwise, the disc will play continuously.

Programmed play (CD)

1. While in the stop mode, press the MEMORY button on the remote control to enter the programming save mode.
2. Press the ◀◀ or ▶▶ button to select the desired track.
3. Press the MEMORY button to save the track number.
4. Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be programmed. If you want to check the programmed tracks, during stop mode, press the MEMORY button repeatedly. To clear the programmed tracks, press the CLEAR button.
5. Press the ▶/II (CD ▶/II) button to start playback.

To cancel the programmed play mode: During programmed stop mode, press the ■ button. The display will show "Memory Clear" and all the programmed contents will be cleared.

Adding tracks to the program:

If a program has been previously stored, the "MEM" indicator will be displayed. During stop mode, press the MEMORY button once. Within 10 seconds, press and hold the MEMORY button again. Then follow steps 2 - 3 to add tracks.

Notes:

• When the disc compartment is opened, the program is automatically canceled.
• If you press the ON/STANDBY button to enter the standby mode or change the function from CD to another, the programmed selections will be cleared.

Procedure to playback MP3/WMA disc with folder mode on

To play back CD-R/RW.

1. In CD function, load an MP3/WMA disc. Press the FOLDER button and disc info will be displayed.

(Diagram description: Shows display information for MP3/WMA disc, including total number of folders and files.)

(Diagram description: Shows the FOLDER indicator and first track number in the folder.)

2. Press the PRESET ( ▼ or ▲ ) button to select desired playback folder. (Folder mode on)
3. Select desired file to be played back by pressing the ◀◀ or ▶▶ button.
4. Press the ▶/II (CD ▶/II) button. Playback will start and file name will be displayed.

Programmed play (MP3/WMA)

1. While in the stop mode, press the MEMORY button to enter the programming save mode.
2. Press the PRESET ( ▼ or ▲ ) button on the remote control to select the desired folder.

(Diagram description: Shows display for folder and song selection in MP3/WMA programmed play.)

Then press the ◀◀ or ▶▶ button (remote control) to select the desired tracks.

3 Press the MEMORY button to save the folder and track number.

4 Repeat steps 2 - 3 for other folder/tracks. Up to 32 tracks can be programmed.

5 Press the ▶/II (CD ▶/II) button to start playback.

Note:

• Title, Artist and Album name are displayed if they are recorded on the disc.
• In case of playback with the folder mode on, press the PRESET ( ▼ or ▲ ) button, and the folder can be selected even though it is in playback/pause mode. It will continue playback/pause mode in the 1st track of the selected folder.
• Display content can be changed by pressing the DISPLAY button.

File name display

• Folder display
• Counter display
• Title display
• Album display
• Artist display

Note: If "Not Support" is displayed, it means "Copyright protected WMA file" or "Not supported playback file" is selected.