DBPOWER G60 Jump Starter

A Big Thank You

We're thrilled that you have chosen to purchase the DBPOWER jump starter. At DBPOWER, we're committed to providing you with products that enhance your daily life. We also aim to give our customers excellent support. Should you have any questions or feedback about your new product, simply get in touch with our customer support team at 1-855-888-5533, or by email at support@dbpowershop.com

Enjoy your new product!

Attention & Safety Precautions

Detailed Precautions:

• This device is suitable for All petrol engines and diesel engines up to 10L. Please don't attempt a vehicle with a higher engine capacity or it will cause serious damage to the device and could be dangerous to the user.
• Don't crank the engine for more than 3 seconds. Allow the jump starter to cool down for at least 1 minute after each start.
• Your jump starter will work best when it is fully charged. If less than 50% charged, it will not be able to start your engine.
• Clear the dust on the electrodes of your car battery before jump starting.
• If the instructions are followed correctly but your vehicle doesn't start instantly, please wait for 5-10 minutes and try again. But please don't make repeated attempts to jump start the engine without allowing time for the device to cool down.
• Do not connect the positive and negative polarity clamps together when the device is powered on. A short circuit can cause electric shock and serious injury.
• Disconnect the cables from the jump starter and car battery when not in use, remove the negative clamp from car battery terminal (or positive first for positive ground systems).
• It is prohibited to charge the device immediately after a jump start. Please wait at least 30 minutes if you want to charge the device after a jump start.
• To preserve lifespan, recharge the device at least once every 3 months.
• Use original or certified cables.
• Do not expose the jump starter to liquids. Do not disassemble.
• Avoid dropping the device and exposing it to extreme temperatures.
• The storage temperature shouldn't exceed 95°F (35°C) and operating temperature shouldn't exceed -4°F-140°F (-20°C-60°C), otherwise, the battery will expand.

Accessories

The following accessories are included with your DBPOWER G60 Jump Starter:

• 1 x Intelligent Jumper Clamps: Cables with clamps for connecting to the car battery.
• 1 x USB Cable: Cable for charging the jump starter or other devices.
• 1 x User Manual: This guide.
• 1 x Storage Bag: For convenient storage and transport.

Specifications

At a Glance

Familiarize yourself with the components of your DBPOWER G60 Jump Starter:

• 1. Power Button: Turns the device on and off, and controls the LED light.
• 2. Jump Start Output & Dust Plug: Port for connecting the jumper cables, protected by a dust plug.
• 3. USB Output*2: Two standard USB ports for charging mobile devices.
• 4. Type-C In(OUT): USB Type-C port for input charging of the jump starter.
• 5. LED Flashlight: Integrated flashlight for visibility.
• 6. DC Output: A DC output port for other compatible devices.
• 7. Jumper Clamps: The red and black clamps that connect to the vehicle's battery terminals.

How to Jump Start Your Car

Important: Before attempting to jump-start a vehicle, ensure all power loads (headlights, radio, air conditioning, etc.) are turned off.

Step 1: Preparation

Press the power button on the Jump Starter. Ensure the device has at least 50% battery charge. For initial use, it is recommended to fully recharge the jump starter.

Step 2: Connect Jumper Cables to Jump Starter

Fully insert the jumper cables into the designated jump start output socket on the jump starter. A blinking green light indicates the cables are correctly connected to the jump starter.

Step 3: Connect Clamps to Car Battery

Connect the red clamp to the positive (+) terminal of the car battery and the black clamp to the negative (-) terminal.

Step 4: Start the Engine

Once connections are secure, the green indicator light on the jump starter should be steady. Attempt to start the car engine. If the engine does not start within 30 seconds, the jump start function may time out, and you will need to reconnect the clamps and try again.

Step 5: Disconnect Cables

After the car has successfully started, the green indicator light will likely strobe. Carefully remove the jumper clamps from the car battery, first the negative, then the positive. Disconnect the cables from the jump starter and store them.

Jumper Cables Indicator Light Instructions:

• Green Light Blinking: Jumper cable connected correctly to the jump starter, ready to connect to the car.
• Green Light ON: All connections are correct; attempt to start the engine.
• Green Light Flashing: Connection timed out; reconnect the clamps to the car battery terminals.
• Green Light Strobing: Car has started; remove the jumper cables.
• Red Light ON with Beep Sound: Error in connection; refer to the 'Attention' section (page 5) and try again.

Precautions for Jump Starting:

• Connect the jumper cables correctly as per the manual's instructions.
• Avoid jump-starting the car at high frequency continuously.
• Do not heat or use the jumper cables near fire.
• Do not immerse the jumper cables in water or attempt to disassemble or modify them.
• Always connect the jumper cable to the jump starter first, then to the car battery for ignition to prevent misjudgment.
• When the car battery is not connected, the cable clips do not have reverse connection protection. If you remove the power cord from the car battery, do not connect it in reverse when starting the car.

How to Charge Phones or Tablets

Connect your mobile phones or tablets using a compatible power cord and plug the other end into one of the USB-1 or USB-2 ports on the jump starter for recharging.

Note: The USB to USB power cord is not included in the package. The 'Output 1' and 'Output 2' ports cannot function while the Type-C input port is being used to recharge the jump starter itself.

How to Use the LED Light

1. Short press the power button to turn on the jump starter.
2. To activate the flashlight, hold the power button for 2 seconds.
3. You can then short-press the power button to cycle through flashlight modes: High brightness, SOS, and Strobe.
4. To turn the flashlight off, hold the power button for 2 seconds again.

How to Recharge the Device

The wall plug adapter is not included. Please use a universal charging adapter (5V or higher) to charge the device. It is recommended to recharge the jump starter using the included charging cable.

Please Note: The Type-C port is exclusively for input charging of the jump starter and cannot be used to charge mobile phones or tablets.

Q&A

Question 1: My car is compatible with the device, but unable to start?

The performance of the jump starter can be affected by external factors such as the age of the engine, weather conditions, and the car's remaining battery power. If you encounter difficulty starting your car engine, we recommend fully charging the device, cleaning any dust or dirt from the car battery electrodes, and trying again. Remember to allow the device to cool down for at least 60 seconds between each attempt. Avoid making repeated attempts to start your vehicle without proper cooling intervals.

Question 2: Why is the battery percentage dropping rapidly when upon receiving the jump starter?

The jump starter may have been stored for some time before delivery. Consequently, the battery might be significantly discharged. This could lead to a rapid drop in the displayed percentage when you first power on the device. It is recommended to give the jump starter a full recharge after you receive it to ensure optimal performance.