Home - Blaupunkt
Instruction Manual for BLAUPUNKT models including: XLf 185 A Active Subwoofer, XLf 185, A Active Subwoofer, Active Subwoofer, Subwoofer
XLf 185 A - Blaupunkt
File Info : application/pdf, 8 Pages, 744.81KB
DocumentDocumentACTIVE SUBWOOFER XLf 185 A Operating and Installation Instructions CAUTIONS Proper system planning is vital in order to maximize the device's performance and road safety. Plan your installation carefully to avoid compromising performance reliability of the system. Consult an authorized Blaupunkt dealer for installation or preparation. Read the manual carefully before operating the device for the first time. USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada. Remote Control Safety Notes Ensure to follow below safety notes during installation and wiring connection: - 1. Power Indicator 2. Gain Adjustment · Disconnect the negative terminal of the battery. Refer to the safety notes of the vehicle manufacturer. · Ensure positions of the holes are nowhere near the vehicle component to avoid any damage during drilling. · Ensure cross section of the cable is no less than 2.5mm if the positive and negative cables are too long. · Incorrect installation may result in malfunction of the device or the car sound system. Installation and Connection Instructions · Select a dry and well-ventilated location to install the device. · The device must not be installed in overly exposed location such on the rear shelf, rear seat etc. · The installation location must be suitable for screw holes and have stable ground support. Turn the gain knob to adjust the volume to the desired level. Disposal Notes Do not dispose of your old unit in the household trash! Use the return and collection systems available to dispose of the old device. This manual may be updated from time to time without any notice. Visit www.blaupunkt.com for more info. Intergrated Fuse · The integrated fuse in the device protects the output voltage and the entire electrical system in case of malfunction. Do not replace damaged fuse with higher current. Switching On/Off · This device will automatically turn on if audio signal is detected. The device will also automatically turn off if audio signal is received. Disclaimer In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products. 1 FUNCTIONS CONTROLLING DIAGRAM 1 23 45 1. Power / Speaker Input 2. RCA Input (CH1/ CH2) 3. Remote Control Input 4. Phase (0º~ 180º) 5. Auto Power On (On/Off ) 6. Input Gain (200mV ~ 6V) 7. Bass Boost (0 ~ +18dB) 8. Low Pass (50Hz ~ 150Hz) 9. Power LED Light 10. Protection LED Light INSTALLATION 6 7 8 9 10 2 INSTALLATION POSITION Down Firing Position Side Firing Position Up Firing Position 3 SPECIFICATION 345mm 260mm 75mm Subwoofer · Speaker Size : 8.0" · Cone Composition : Aluminium · Magnet Type : Ferrite · Enclosure Housing Material : Aluminum · Enclosure Dimension (L x W x H) : 345 x 260 x 75mm · Enclosure Net Weight : 5kg Amplifier · Amplifier Technology : Class AB · Normal Output Power (RMS) : 180W · Max Output Power : 450W · Audio in Sensitivity : RCA input 0.2V-10V, Speaker input 0.6V-12V Accessories · Signal/Noise Ratio : 91dB · Output Impedance : 2 ohms · Frequency Response : 30Hz-150Hz · Low Pass Filter (LPF) : 50Hz-150Hz · Voltage : 14.4V (10V-16V) · Phase Switch : 0 deg /180 deg · Automatic On/Off : High Level Only · Gain : 200mV 6V · Passive Radiator : 192 x 60mm · Variable Bass Boost : 0 18dB 2x Screws (M6x8) 2x Screws (M4x20) 2x Mounting Bracket (71 x 39.5 x 7mm) 1x 4.5m Remote Controller 1x 4.5m DC Cord High level Input Speaker Extension Low level Input Speaker Extension 3 Input Plug Extension WIRING DIAGRAM Use the supplied cable and wire harness to connect the outputs correctly by referring to Diagram 1 & Diagram 2. Diagram 1 (High Level Input -Speaker Input) Diagram 2 (Low Level Input -RCA Input) 4 TROUBLESHOOTING If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt authorized dealer if problem persist. Problem Amplifier power up failure Protection LED lights on when turn on No sound output Low sound output Buzzing noise Squealing noise interference Distorted sound output Amplifier temperature increased Engine noise (static sound) interference Engine noise (alternator whine) interference Solution Examine if the ground connection is intact. Examine if remote input has at least 5V DC. Examine if battery power is connected correctly to the + terminal. Ensure supplied voltage is minimum 12V. Examine if fuse is broken and replace if necessary. Restart the device if protection LED light is on. Examine if speaker wire had short-circuit. Turn volume down from head unit to prevent overdriving the device. Device might need service or repair, if protection LED light is still on after resetting the device. Examine fuses and replace if necessary. Examine if ground connection is intact. Examine if remote input has at least 5V DC. Examine if RCA audio cables are connected to the right inputs. Examine if speaker wiring is intact. Reset Level Control Examine the Crossover Control setting. Observe if the device is still producing noise after turning on and off the amplifier. If yes, examine if the cables are correctly connected and if the cables and radio are in good condition. Repair or replace if the cables or the radio are not in good condition. Ensure RCA connections are properly connected. Ensure input level of the device matches the signal level of the head unit. Always set the input level to the lowest. Examine if crossover frequency is set correctly. Examine if speaker wire had short-circuit. Examine if the minimum speaker impedance for the amp models is correct. Ensure good air ventilation around the device. Add external cooling fan if necessary. Usually caused by poor RCA cable quality, which release noise. Use only the best quality cables, and route them away from power cables. Examine if RCA cable are nowhere near or attached to the vehicle chassis. Examine if head unit is properly connected to the wires. 5 Designed and engineered by Blaupunkt Competence Centre 1 113 22 027 02 01