ASSMANN Electronic GmbH | Lüdenscheid, GermanyASSMANN Electronic GmbH | Lüdenscheid, Germany
Installation Guide for DIGITUS models including: DN-651160, DN-651161, DN-651160 Uplink Port L3 Managed Gigabit Ethernet Switch, Uplink Port L3 Managed Gigabit Ethernet Switch, Port L3 Managed Gigabit Ethernet Switch, Managed Gigabit Ethernet Switch, Gigabit Ethernet Switch, Ethernet Switch, Switch
Web 2 days ago · 3 1. Overview This is a L3 managed industrial PoE Ethernet switch with 8 Port 10/100/1000Mbps RJ45 (PoE) 4 Port 1000/2500/10000Mbps SFP, support one …
Digitus DN-651160 Industrial Ethernet Switch 8 4 Port 1 GBit/s – Conrad Electronic Schweiz
File Info : application/pdf, 12 Pages, 671.34KB
DocumentDocumentIndustrial 8 + 4-port L3 managed Gigabit Ethernet (PoE) Switch Quick Installation Guide DN-651160, DN-651161 Table Content 1. Overview ..................................................... 3 2. Features....................................................... 3 3. Specification ................................................ 4 3.1 standard...................................................... 4 3.2 Interface...................................................... 5 3.3 Work environment...................................... 5 3.4 Switch ......................................................... 5 3.5 Power supply .............................................. 5 3.6 Mechanical characteristic ........................... 6 3.7 Industrial standard...................................... 6 4. Package........................................................ 6 5. Switch Panel................................................. 7 6. LED Indicator................................................ 8 7. Installation Caution ...................................... 9 7.1 Installation precautions .............................. 9 7.2 Din rail installation .................................... 10 7.3 grounding.................................................. 10 7.4 Power Connection .................................... 10 8. Management system Login ..........................11 2 1. Overview This is a L3 managed industrial PoE Ethernet switch with 8 Port 10/100/1000Mbps RJ45 (PoE) +4 Port 1000/2500/10000Mbps SFP, support one console port. The Ethernet switch adopts Layer 2 protocol required by the industrial site to ensure the stability of the communication network. This series of switches adopt low power consumption and fanless design to ensure no noise interference, while supporting -40~80°C working temperature and good EMC electromagnetic compatibility performance to ensure stable work in harsh industrial environments, and to build fast for industrial applications such as factory automation, intelligent transportation, and video surveillance. Stable network terminal access network provides a safe and reliable solution. 2. Features Data control: support 802.3X full-duplex flow control, support network storm suppression Redundant network: support STP/RSTP/MSTP, support ERPS (self-healing time <20ms) Multicast management: support IGMP Snooping V1/V2/V3 Redundancy backup: supports the virtual route redundancy protocol VRRP 3 VLAN: Support IEEE 802.1Q VLAN, effectively isolate the broadcast domain Link aggregation: support link static/dynamic aggregation, providing perfect bandwidth utilization QOS: Support COS\DSCP, 4 queues, support WRR\SP scheduling mode Security management: support ACL access control list, support 802.1X Management function: support WEB, CLI, SNMP management methods Monitoring and maintenance: support port mirroring, interface status monitoring, log management Supports static routes. IPV6 Supports NTP clients. Support PTP1588v2 IP40 protection grade 3. Specification 3.1 standard IEEE802.3i 10Base-T,IEEE802.3u 100Base-TX, IEEE802.3ab 1000Base-T,IEEE802.3z 1000Base-X,IEEE 802.3ae 10GBase-X,IEEE802.3x Flow Control,IEEE802.1d-Spanning Tree Protocol,IEEE802.1w-Rapid Spanning Tree Protocol,IEEE802.1q-VLAN , IEEE 802.3ad, IEEE802.1pClass of Service,IEEE802.1X-Port Based Network Access Control,IEEE802.3af,IEEE802.3at etc. 4 3.2 Interface DN-651160: 8 Port Gigabit RJ45 + 4port 10G SFP DN-651161: 8 Port Gigabit RJ45 (PoE) +4 Port 10G SFP 3.3 Work environment Working temperature: -4080 °C storage temperature: -4085 °C relative humidity: 5%95% (no condensation) 3.4 Switch Bandwidth (switch capacity): 1.2Tbps Packet Buffer Memory: 32Mbit Packet Forwarding Rate: 406Mpps MAC Address Table: 32K 3.5 Power supply Input voltage: DC12-48V (DN-651160) Input voltage: DC48-57V (DN-651161) (Two-way power redundancy backup) Access terminal: Block terminal, Support dual power redundancy Support built-in over current 4.0A protection Support reverse connection protection Max Power consumption: 18W 5 3.6 Mechanical characteristic IP40 aluminum housing DIN rail installation Natural colling, no fan Weight: 0.8Kgs Measurement: 175.6 x 135 x 45.5 mm 3.7 Industrial standard FCC CFR47 Part 15, EN55032, Class A IEC61000-4-2 (ESD): ±8kV (contact), ±12kV (air) IEC61000-4-3 (RS): 10V/m (80~1000MHz) IEC61000-4-4 (EFT): Power Port: ±2kV; Data Port: ±1kV IEC61000-4-5 (Surge): Power Port: ±2kV/CM, ±1kV/DM; Data Port: ±4kV/CM, ±2kV/DM IEC61000-4-6 (CS): 3V (10 kHz-150 kHz); 10V (150 kHz-80MHz) IEC61000-4-16 (Common mode conduction): 30V (cont.), 300V (1s) Frequency range150kHz-80MHz Impact: IEC 60068-2-27 Free Fall: IEC 60068-2-32 Vibration: IEC 60068-2-6 4. Package Industrial switch 1pcs User manual 1pcs Block terminal 1pcs 6 5. Switch Panel Side panel: P1 and P2 are the number of connecting terminals, P+1 and P-1 are respectively to the positive and negative poles to be connected; Earthing screw used for earthing equipment. Front panel: the yellow light on RJ45 port is the link light. It is on, when the connection is established and the transmission data is flashing. The green light on RJ45 port is the POE light, which is only on when the switch port supplies power to the downlink PD. Green LED on is for system operation. The power indicator "POW" shows whether the current device is received power in normal. There are also green LED for optical link status. 7 Switch size (mm) 175.6* 135*45.5 6. LED Indicator LED Indicator Status Power Red LED on Red LED off Yellow LED on RJ45 LED Yellow LED flashing Green LED on Green LED off Definition Power work in normal No power or power in trouble Ethernet work in normal Link communication in normal PoE feeding to PD device in normal No PoE work 8 RUN Optical LED Green LED slowing flashing Green LED on System run in normal Optical work in normal 7. Installation Caution 7.1 Installation precautions In order to avoid damage to equipment and personal injury caused by improper use, please follow the following precautions: In order to avoid damage caused by falling of the equipment, please put the equipment in a stable environment. When supplying power to the equipment, pay attention to confirm the range of power supply voltage, as well as the positive and negative poles of the power supply, so as not to damage the equipment by wrong operation. In order to reduce the risk of electric shock, ensure that the equipment is well grounded in the working environment. No matter when, please do not arbitrarily remove the equipment shell. When placing the switch, please avoid the area with dust and strong electromagnetic interference 9 7.2 Din rail installation The first step is to check the grounding and stability of the guide rail: the guide rail slot of the switch is clamped into the guide rail; the second step: from the center to both sides of the guide rail positioning screws in order. Step 3: Use screws to fix the mounting rail card slot on the fixed guide groove at both ends of the guide rail to ensure that the guide rail and the switch are fixed on the guide rail vertically and stably. 7.3 grounding Fix the grounding wire to the grounding screw above the switch, and ensure good reliable connection of the grounding system. 7.4 Power Connection Insert the power cord into the specified position of the 6-core terminal, and insert the terminal into the standard power supply inlet (P+1 and P-1 input corresponding to the first power supply P1, and P+2 and P-2 input corresponding to the second power supply P2). 10 8. Management system Login This series of Managed ethernet switches provides a serial port-based management system program debugging port. Located at the front of panel to log in to the command line. Console port: baud rate 115200 Web IP: 192.168.10.12 User name: admin Password: admin For detail Web manual support, please visit product website at www.assmann.com 11 This is a Class A product. In home environment, this product may cause radio interference. In this case, the user may be required to take appropriate measures. Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address www.assmann.com ASSMANN Electronic GmbH Auf dem Schüffel 3 58513 Lüdenscheid, Germany 12