Lutron | Intelligent light. Automated Shades. Powerful Controls
Lutron | Intelligent light. Automated Shades. Powerful ControlsLED Driver Selection Tool MasterTemplate.htmllutron.com/driverwarranty
User Guide for LUTRON models including: T-Series LED Dimming Driver
T-Series LED Driver SPECIFICATION SBMITTAL Page ob Name: ob Number: Model Numbers: LED Dimming Driver Tunable White 3691099i 1 05.11.20 T-Series LED Drivers provide a high-performance
Driver consumes two digital addresses: one for intensity and one for color temperature. • Guaranteed performance and compatibility when.
File Info : application/pdf, 13 Pages, 1.07MB
DocumentDocumentLED Dimming Driver
T-Series LED Driver
Tunable White
T-Series LED Driver
T-Series LED Drivers provide a high-performance tunable white solution.
Features
· ULR 8750 Listed Class P · Each output capable of 100% to 0.1% dimming * · For best tunable white performance, operate at 1% or
higher. See page 10 for more details · Dimming Method:
Constant-current reduction (CCR) dimming to 200 mA
Pulse-width modulation (PWM) dimming below 200 mA e PWM Frequency = 3.6 kHz e Outputs of the two channels are synchronized
· Driver consumes two digital addresses: one for intensity and one for color temperature
· Guaranteed performance and compatibility when used with Lutron T-Series controls: T-Series Energi Savr Node unit as part of a Quantum system
· Guaranteed compatibility with T-Series Energi Savr Node as a part of a Quantum system
· QwikFig Air compatible · Protected from miswires of input power to T-Series
control inputs up to 277 V~ · Rated lifetime of 50,000 hours at 167 °F (75 °C)
calibration point (tc) for W case and 158 °F (70 °C) calibration point (tc) for Y case · FCC Part 15 Class A
· 100% performance tested at factory before shipping.
· RoHS compliant
· For more information please visit: www.lutron.com
3691099i 1 05.11.20
N L
50017812
lutron.com
T-Series LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico:
+1.888.235.2910
Warranty void if unit opened. | Garantie annulée si ouvert. La garantia sera nula si se abre la unidad.
T-Series LED Driver
PSQ02UWN-5ABLK Input | Entrée | Entrada Output | Sortie | Salida
120 - 277 V~ CV 50 / 60 Hz 0,52 - 0,25 A Max 62 W
0 784276 180344
8 - 54 V- 60 V- Max 200 - 1500 mA CC 50 W Max
Channels | Canaux |
Caneles: 2
CLASS P
Clase P E322469
Wire: Solid, 20-16 AWG, 90 °C
Alambre: Sólido, 20-16 AWG, 90 °C
Fil: Solide, 20-16 AWG, 90 °C t c
Cu Al
0,35 in. (9 mm)
T2 C2-
N L
LED Driver
T1 C2+ T2 C1-
T1 C1+
Class B | Classe B | Clase B
For rated warranty tc 75 °C max. | Pour garantie nominale tc 75 °C max. | Para la garantia nominal tc 75 °C max.
En México: Importado Por: Lutron CN. S. De R.L. De C.V.
Gabriel Mancera 1041 Colonia Del Valle, México DF. 03100 México
B3
WARNING: Shock hazard. May result in serious injury or death. More than one power supply is present, disconnect power before
To remove wire, insert screwdriver into slot. Pour enlever le fil, insérez un tourneviz dans la fente.
T2
servicing or installing.
Para retirar el cable, insertar destornillador en la ranura. T1
AVERTISSEMENT : Risque d'électrocution. Peut causer des blessures graves ou la mort. Plus d'une alimentationest présente, déconnectez
Suitable for damp locations. Indoor Use Only.
N/C
l'alimentation avant d'effectuer l'entretien ou l'installation.
Convient aux emplacements humides. Usage intérieur
T2
ADVERTENCIA: Peligro de descarga eléctrica. Podría ocasionar lesiones graves o la muerte. Hay presente más de una fuente de alimentación; desconecte la alimentación eléctrica antes de brindar mantenimiento o
seulement.
Adecuado para lugares humedos. Solamente para uso en interiores.
T1 N/C
instalar. Assembled in China | Assemblé en Chine | Ensamblado en China
C1= Cool White | blanc froid | Blanco frio
PCB
C2= Warm White | blanc chaud | blanco cálido
N/C N/C
Class 2 Cool Warm
C2C2+ C1C1+
Case Type W 1.18 in (30 mm) W x 0.83 in (21.0 mm) H x 16.06 in (408 mm) L
lutron.com
T-Series
LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico:
+1.888.235.2910
C2+
C2-
L N
Class 2
LED
C1+
C1-
Driver
T1 T2 T1
T2
Class B | Classe B | Clase B
T-Series LED Driver
PSQ02UYS-5ABLK
Input | Entrée | Entrada Output | Sortie | Salida
120 - 277 V~ CV
t c
50 / 60 Hz 0,52 - 0,25 A Max
62 W
0 784276 180375
8 - 54 V- 60 V- Max 200 - 1500 mA CC 50 W Max
Clase P
Channels | Canaux |
Caneles: 2
CLASS P E322469
For rated warranty tc 70 °C max. | Pour garantie nominale tc 70 °C max. | Para la garantia nominal tc 70 °C max.
PCB
C1= Cool White | blanc froid | Blanco frio C2= Warm White | blanc chaud | blanco cálido
Assembled | Ensamblado | Assemble: China | Chine
WARNING: Shock hazard. May result in serious injury or death. More than one power supply is present, disconnect power
before servicing or installing.
AVERTISSEMENT : Risque d'électrocution. Peut causer des blessures graves ou la mort. Plus d'une alimentationest présente, déconnectez
l'alimentation avant d'effectuer l'entretien ou l'installation.
ADVERTENCIA: Peligro de descarga eléctrica. Podría
L
ocasionar lesiones graves o la muerte. Hay presente más de una fuente de alimentación; desconecte la alimentación
N eléctrica antes de brindar mantenimiento o instalar.
En México: Importado Por: Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041 Colonia Del Valle México DF. 03100 México
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia sera nula si se abre la unidad.
Suitable for damp locations. Indoor Use Only. | Convient aux emplacements humides. Usage intérieur seulement. | Adecuado para lugares humedos. Solamente para uso en interiores.
Wire: Solid, 20-16 AWG, 90 °C Alambre: Sólido, 20-16 AWG, 90 °C Fil: Solide, 20-16 AWG, 90 °C
Cu Al 0,35 in. (9 mm)
To remove wire, insert screwdriver into slot. | Pour enlever le fil, insérez un tourneviz dans la fente. | Para retirar el cable, insertar destornillador en la ranura.
Cool Warm
C2+ C2C1+ C1N/C N/C N/C N/C N/C T1 T2 N/C T1 T2
50017898
Case Type YS 3.0 in (76.0 mm) W x 1.14 in (29.0 mm) H x 5.91 in (150.0 mm) L
Class 2 Cool Warm
lutron.com
T-Series
LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico:
+1.888.235.2910
C2+
C2-
L N
LED
C1+ C1-
Driver
T1 T2 T1
T2
T-Series LED Driver
PSQ02UYN-5ABLK
Input | Entrée | Entrada Output | Sortie | Salida
120 - 277 V~ CV
t c
50 / 60 Hz 0,52 - 0,25 A Max
62 W
8 - 54 V- 60 V- Max 200 - 1500 mA CC 50 W Max
Clase P
Channels | Canaux |
Caneles: 2
CLASS P E322469
For rated warranty tc 70 °C max. | Pour garantie nominale tc 70 °C max. | Para la garantia nominal tc 70 °C max.
PCB
C1= Cool White | blanc froid | Blanco frio C2= Warm White | blanc chaud | blanco cálido
Class B | Classe B | Clase B
Assembled | Ensamblado | Assemble: China | Chine
WARNING: Shock hazard. May result in serious injury or death. More than one power supply is present, disconnect power
before servicing or installing.
AVERTISSEMENT : Risque d'électrocution. Peut causer des blessures graves ou la mort. Plus d'une alimentationest présente, déconnectez
l'alimentation avant d'effectuer l'entretien ou l'installation.
ADVERTENCIA: Peligro de descarga eléctrica. Podría
L
ocasionar lesiones graves o la muerte. Hay presente más de una fuente de alimentación; desconecte la alimentación
N eléctrica antes de brindar mantenimiento o instalar.
En México: Importado Por: Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041 Colonia Del Valle México DF. 03100 México
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia sera nula si se abre la unidad.
Suitable for damp locations. Indoor Use Only. | Convient aux emplacements humides. Usage intérieur seulement. | Adecuado para lugares humedos. Solamente para uso en interiores.
Wire: Solid, 20-16 AWG, 90 °C Alambre: Sólido, 20-16 AWG, 90 °C Fil: Solide, 20-16 AWG, 90 °C
Cu Al 0,35 in. (9 mm)
To remove wire, insert screwdriver into slot. | Pour enlever le fil, insérez un tourneviz dans la fente. | Para retirar el cable, insertar destornillador en la ranura.
C2+ C2C1+ C1N/C N/C N/C N/C N/C T1 T2 N/C T1 T2
50017898
Case Type YN 3.0 in (76.0 mm) W x 1.14 in (29.0 mm) H x 5.91 in (150.0 mm) L
T-Series Digital Link Features
· Simpler to wire and more reliable than 0 10 V· Guarantees compatibility between Lutron controls
and LED drivers · Accommodates zone and control changes
without rewiring · Connect to Quantum Total Light Management
Systems to monitor lighting power consumption · Polarity-free and topology-free · Allows easy code compliance · T-Series digital link can be Class 1 or Class 2 · Non-volatile memory restores all settings after
power failure
* Light output at low-end depends on the efficacy of the LED light engine used with the driver.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 1
LED Dimming Driver
T-Series LED Driver
Tunable White
Specifications
3691099i 2 05.11.20
Regulatory Approvals and Compliance
· cULus Listed Class P · NOM certified · Lutron Quality Systems registered to ISO 9001.2015 · Inrush current less than NEMA 410-2011 limit
· FCC Part 15 Class A · Meets UL® 8750, "Light Emitting Diode (LED)
Equipment For Use in Lighting Products" · Class 2 outputs · Compliant with perfomance criteria for ENERGY STAR
for Luminaires Version 2.1 in designated areas (see Load Compatibility graph in Output Ranges page 6) · Compliant with DLC version 4.3 in designated areas (see Load Compatibility graph in Output Ranges page 6) (for W case only)
Performance · Dimming Range: 100% to 0.1% 1
· Operating Voltage: 120 V~ / 277 V~ at 50 / 60 Hz · Lifetime: 50,000 hours when calibration point (tc) at
167 °F (75 °C) for W case and 158 °F (70 °C) for Y case 2
· ULR allows operation of tc up to 90 °C · For rated warranty, tc not to exceed 167 °F (75 °C) for
W case and 158 °F (70 °C) for Y case (maximum rated temperature) 2
· At turn on, lighting goes to the desired level without decreasing or flashing to full brightness
· Typical standby power consumption: < 0.5 W at 120 V~ / 277 V~
· Open-circuit protected output
· Short-circuit protected output
· Over temperature protected
Environmental
· Sound rated: Class A inaudible in 24 dBA ambient
· Relative Humidity: maximum 90% non-condensing
· Minimum Operating Ambient Temperature: ta = 0 °C (32 °F)3
· Indoor use only
· Rated for dry and damp locations
OEM Notes
· For best dimming performance, Lutron recommends electrical insulation with 50 / 60 Hz impedance of at least 12 M and minimum breakdown voltage of at least 1500 V~ between LEDs and fixture chassis
Driver Wiring and Mounting
· Driver is grounded by a mounting screw to the grounded fixture or by a terminal connection.
· It is possible to daisy-chain the T-Series digital link using the second set of terminal blocks. See example on page 10
· Fixture must be grounded in accordance with local and national electrical codes
· The positive terminals of both output channels are electrically connected inside the driver. This supports the use of common anode loads
· Terminal blocks on the driver accept one solid wire per terminal from 20 AWG to 16 AWG (0.5 mm2 to 1.5 mm2)
· Maximum driver-to-LED light engine wire length for:
Wire Gauge
18 AWG (0.75 mm2) 16 AWG (1.5 mm2) 14 AWG (2.5 mm2)4 12 AWG (4.0 mm2)4
Maximum Lead Length
150 mA to 710 mA to 1.51 A to
700 mA
1.50 A
2.10 A
30 ft (9 m) 15 ft (4.5 m) 10 ft (3 m)
35 ft (10.5 m) 25 ft (7.5 m) 15 ft (4.5 m)
50 ft (15 m) 40 ft (12 m) 25 ft (7.5 m)
100 ft (30 m) 60 ft (18 m) 40 ft (12 m)
1 For best tunable white performance, operate at 1% or higher. Light output at
low-end depends on the efficacy of the LED light engine used with the driver. 2 To maintain warranty, installer is responsible for ensuring that the driver calibration
point does not exceed 167 ºF (75 ºC) for W case and 158 ºF (70 ºC) for Y case. 3 Where ta is the temperature of the air directly surrounding the driver. 4 Terminal blocks on the drivers accept only solid 20 AWG to 16 AWG (0.5 mm2 to
1.5 mm2) wire. To use wire gauges larger than the terminal blocks' rated gauge of 16 AWG (1.5 mm2), connect up to 3 ft (1.0 m) of 20 AWG to 16 AWG (0.5 mm2 to 1.5 mm2) wire to the LED driver terminal blocks, then connect 12 AWG or 14 AWG (4.0 or 2.5 mm2) up to the length allowed in the above table.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 2
LED Dimming Driver
T-Series LED Driver
Tunable White
3691099i 3 05.11.20
How to Determine Compatibility Between an LED Driver and LED Load
1. Review the specifications of the LED load.
2. Identify the minimum and maximum operating voltage of the LED load at the desired operating current. This "current" will be the rated output current of the LED driver. Consult the LED load manufacturer for any questions.
Example: An LED load that is rated at 0.7 A and 30 V nominally, has an input (forward) voltage range of 25 35 V (at 0.7 A) due to unit-to-unit variation, temperature, etc.
3. Examine the LED driver Load Compatibility graphs below for each output range to ensure that the voltage range of the LED load is within the load compatibility range.
Example: Lines* marked below indicate two load specifications:
Load A (25 35 V) at 0.5 A
Load B (25 35 V) at 0.7 A
Load A (Compatible)
Load B (Not Compatible)
Operating voltage range for load A is 25 35 V at 0.5 A. Since
the load specifications are within the operating range, the combination of LED load and LED driver is compatible.
Since the maximum voltage of the load, 35 V, exceeds the 28.5 V allowable at 0.7 A, this combination of LED load and LED driver is not compatible.
Load Compatibility
60
60
Output Voltage (V) Output Voltage (V)
50
40
30
{ Operating
range of 0.5 A,
35 V
25 35 V load 25 V
20
50
40
30
} 35 V
Operating range of 0.7 A, 25 35 V load
25 V
20
10
10
0 0.00 0.15 0.30 0.45 0.60 0.75 0.90 1.05 1.20 Output Current (A)
0 0.00 0.15 0.30 0.45 0.60 0.75 0.90 1.05 1.20 Output Current (A)
Key:
Constant 20 W output
Constant 54 V output
Key:
Constant 20 W output
Constant 54 V output
4. The LED Driver Selection Tool (www.lutron.com/drivers) is a website compatibility tool that allows for a fast compatibility search of all Lutron LED drivers that are compatible with an LED load.
5. See T-Series Model Number to create the appropriate model number for the desired driver. T-Series drivers are only available as "BLK" drivers for use with QwikFig Air.
* Lines are an example and not the range of the T-Series LED driver.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 3
LED Dimming Driver
T-Series Model Number
T-Series LED Driver
Tunable White
3691099i 4 05.11.20
N L
50017812
lutron.com
T-Series LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico:
+1.888.235.2910
Warranty void if unit opened. | Garantie annulée si ouvert. La garantia sera nula si se abre la unidad.
T-Series LED Driver
PSQ02UWN-5ABLK
Input | Entrée | Entrada Output | Sortie | Salida
120 - 277 V~ CV 50 / 60 Hz 0,52 - 0,25 A Max 62 W
0 784276 180344
8 - 54 V- 60 V- Max 200 - 1500 mA CC 50 W Max
Channels | Canaux |
Caneles: 2
CLASS P
Clase P E322469
Wire: Solid, 20-16 AWG, 90 °C
Alambre: Sólido, 20-16 AWG, 90 °C
Fil: Solide,
20-16 AWG, 90 °C t c
Cu Al
0,35 in. (9 mm)
T2 C2-
N L
LED Driver
T1 C2+ T2 C1-
T1 C1+
Class B | Classe B | Clase B
For rated warranty tc 75 °C max. | Pour garantie nominale tc 75 °C max. | Para la garantia nominal tc 75 °C max.
En México: Importado Por: Lutron CN. S. De R.L. De C.V.
Gabriel Mancera 1041 Colonia Del Valle, México DF. 03100 México
B3
WARNING: Shock hazard. May result in serious injury or death. More than one power supply is present, disconnect power before
To remove wire, insert screwdriver into slot. Pour enlever le fil, insérez un tourneviz dans la fente.
T2
servicing or installing.
Para retirar el cable, insertar destornillador en la ranura. T1
AVERTISSEMENT : Risque d'électrocution. Peut causer des blessures graves ou la mort. Plus d'une alimentationest présente, déconnectez
Suitable for damp locations. Indoor Use Only.
N/C
l'alimentation avant d'effectuer l'entretien ou l'installation.
Convient aux emplacements humides. Usage intérieur
T2
ADVERTENCIA: Peligro de descarga eléctrica. Podría ocasionar lesiones graves o la muerte. Hay presente más de una fuente de alimentación; desconecte la alimentación eléctrica antes de brindar mantenimiento o
seulement.
Adecuado para lugares humedos. Solamente para uso en interiores.
T1 N/C
instalar. Assembled in China | Assemblé en Chine | Ensamblado en China
C1= Cool White | blanc froid | Blanco frio
PCB
C2= Warm White | blanc chaud | blanco cálido
N/C N/C
Cool Warm
C2C2+ C1C1+
W-case type
Cool Warm Class 2
lutron.com
T-Series
LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico:
+1.888.235.2910
C2+
C2-
L N
Class 2
LED
C1+
C1-
Driver
T1 T2 T1
T2
T-Series LED Driver
PSQ02UYS-5ABLK
Input | Entrée | Entrada Output | Sortie | Salida
120 - 277 V~ CV
t c
50 / 60 Hz 0,52 - 0,25 A Max
62 W
0 784276 180375
8 - 54 V- 60 V- Max 200 - 1500 mA CC 50 W Max
Clase P
Channels | Canaux |
Caneles: 2
CLASS P E322469
For rated warranty tc 70 °C max. | Pour garantie nominale tc 70 °C max. | Para la garantia nominal tc 70 °C max.
PCB
C1= Cool White | blanc froid | Blanco frio C2= Warm White | blanc chaud | blanco cálido
Class B | Classe B | Clase B
Assembled | Ensamblado | Assemble: China | Chine
WARNING: Shock hazard. May result in serious injury or death. More than one power supply is present, disconnect power
before servicing or installing.
AVERTISSEMENT : Risque d'électrocution. Peut causer des blessures graves ou la mort. Plus d'une alimentationest présente, déconnectez
l'alimentation avant d'effectuer l'entretien ou l'installation.
ADVERTENCIA: Peligro de descarga eléctrica. Podría
L
ocasionar lesiones graves o la muerte. Hay presente más de una fuente de alimentación; desconecte la alimentación
N eléctrica antes de brindar mantenimiento o instalar.
En México: Importado Por: Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041 Colonia Del Valle México DF. 03100 México
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia sera nula si se abre la unidad.
Suitable for damp locations. Indoor Use Only. | Convient aux emplacements humides. Usage intérieur seulement. | Adecuado para lugares humedos. Solamente para uso en interiores.
Wire: Solid, 20-16 AWG, 90 °C Alambre: Sólido, 20-16 AWG, 90 °C Fil: Solide, 20-16 AWG, 90 °C
Cu Al 0,35 in. (9 mm)
To remove wire, insert screwdriver into slot. | Pour enlever le fil, insérez un tourneviz dans la fente. | Para retirar el cable, insertar destornillador en la ranura.
C2+ C2C1+ C1N/C N/C N/C N/C N/C T1 T2 N/C T1 T2
50017898
YS-case type
lutron.com
T-Series
LED Driver | Pilote de LED | Controlador LED
USA / Canada: 1.844.LUTRON1
Mexico:
+1.888.235.2910
C2+
C2-
L N
Class 2
LED
C1+
C1-
Driver
T1 T2 T1
T2
T-Series LED Driver
PSQ02UYN-5ABLK
Input | Entrée | Entrada Output | Sortie | Salida
120 - 277 V~ CV 50 / 60 Hz
t c 0,52 - 0,25 A Max
62 W
8 - 54 V- 60 V- Max 200 - 1500 mA CC 50 W Max
Clase P
Channels | Canaux |
Caneles: 2
CLASS P E322469
For rated warranty tc 70 °C max. | Pour garantie nominale tc 70 °C max. | Para la garantia nominal tc 70 °C max.
PCB
C1= Cool White | blanc froid | Blanco frio C2= Warm White | blanc chaud | blanco cálido
Class B | Classe B | Clase B
Assembled | Ensamblado | Assemble: China | Chine
WARNING: Shock hazard. May result in serious injury or death. More than one power supply is present, disconnect power
before servicing or installing.
AVERTISSEMENT : Risque d'électrocution. Peut causer des blessures graves ou la mort. Plus d'une alimentationest présente, déconnectez
l'alimentation avant d'effectuer l'entretien ou l'installation.
ADVERTENCIA: Peligro de descarga eléctrica. Podría
L
ocasionar lesiones graves o la muerte. Hay presente más de una fuente de alimentación; desconecte la alimentación
N eléctrica antes de brindar mantenimiento o instalar.
En México: Importado Por: Lutron CN. S. De R.L. De C.V. Gabriel Mancera 1041 Colonia Del Valle México DF. 03100 México
Warranty void if unit opened. | Garantie annulée si ouvert. | La garantia sera nula si se abre la unidad.
Suitable for damp locations. Indoor Use Only. | Convient aux emplacements humides. Usage intérieur seulement. | Adecuado para lugares humedos. Solamente para uso en interiores.
Wire: Solid, 20-16 AWG, 90 °C Alambre: Sólido, 20-16 AWG, 90 °C Fil: Solide, 20-16 AWG, 90 °C
Cu Al 0,35 in. (9 mm)
To remove wire, insert screwdriver into slot. | Pour enlever le fil, insérez un tourneviz dans la fente. | Para retirar el cable, insertar destornillador en la ranura.
Cool Warm
C2+ C2C1+ C1N/C N/C N/C N/C N/C T1 T2 N/C T1 T2
50017898
YN-case type
P S Q 0 2 U M M M A B L K
Case Type
· WN: W Case Type · YS: YS Case Type · YN: YN Case Type
LED Load Output Range: Class 2 Constant Current (see the following pages for more detail)
· 5: 50 W Max, 0.20 1.50 A, 8 54 V-*
* Output voltage range changes with output current and according to power limits. Check driver specifications on the following pages carefully to understand output voltage range of a particular SKU. Purchaser is responsible for electrical compatibility between LED driver and LED load.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Page 4
Job Number:
LED Dimming Driver
T-Series LED Driver
"5" Output Range
Driver Type
Output Voltage
Output Current
Output Power
W-Case Constant Current Driver (Class 2) 8 54 V- 0.20 1.50 A* 50 W**
Standards Recognition
Y-Case
Constant Current Driver (Class 2) 8 54 V- 0.20 1.50 A* 50 W**
Tunable White
3691099i 5 05.11.20
Maximum Rated Temp. @ tc for Warranty 75 ºC 70 ºC
* QwikFig compatible model number PSQ02UWN-5ABLK is configurable to any current within this range in 0.005 A increments. ** Each channel is capable of delivering 50 W. The combined output of both channels must not exceed 50 W total.
Typical Performance Specifications:
W-Case Y-Case
Parameter Input Current Power Factor (PF) Total Harmonic Distortion (THD) Driver Efficiency Input Current Power Factor THD Driver Efficiency
Value 0.25 A 0.95 7%
87% 0.22 A 0.96 9% 88%
277 V~ Test Conditions
Vi = 277 V~ ta = 25 °C Io = 0.90 A Vo = 54 V-
Value 0.5 A 0.99 6%
87% 0.48 A 0.99 9% 88%
120 V~ Test Conditions
Vi = 120 V~ ta = 25 °C Io = 0.90 A Vo = 54 V-
Please see graphs on the following page.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 5
LED Dimming Driver
T-Series LED Driver
"5" Output Range (continued)
Typical Performance Specifications (continued)
Tunable White
3691099i 6 05.11.20
Output Voltage (V)
Load Compatibility
58 53 48 43 38 33 28 23 18
13 8 0.15 0.25 0.35 0.45 0.55 0.65 0.75 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55
Output Current (A)
Key:
Constant 25 W output
Constant 50 W output
Constant 10 W output
Shaded area meets both ENERGY STAR Luminaires V2.1 Specification and DLC Version 4.3 (W case only). Areas outside of shaded areas may not meet THD or PF requirements.
Shaded area meets only ENERGY STAR Luminaires V2.1 Specification. Areas outside of shaded areas may not meet THD or PF requirements.
THD (%)
Typical THD vs Total Power Output
25
20
15 10
5
0 10 15 20 25 30 35 40 45 50
Total Output Power (W)
Key: W Case: YS/YN Case:
120 V~ 120 V~
277 V~ 277 V~
Power Factor
Typical Power Factor vs Total Power Output
1.00
0.95
0.90
0.85
0.80
0.75
0.70 10 15 20 25 30 35 40 45 50 Total Output Power (W)
Key: W Case: YS/YN Case:
120 V~ 120 V~
277 V~ 277 V~
Efficiency at Maximum Output Power (%)
Typical Efficiency vs Output Current
100
80
60 40
20
0
0
0.3
0.6
0.9
1.2
1.5
Output Current (A)
Key: W Case: YS/YN Case:
120 V~ 120 V~
277 V~ 277 V~
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 6
LED Dimming Driver
W Case Dimensions
All measurements shown as: in (mm)
C F
T-Series LED Driver
A B
A = 16.06 (408) B = 15.79 (401) C = 1.18 (30) D = 0.827 (21) E = 0.165 (4) F = 0.59 (15)
B A
Tunable White
3691099i 7 05.11.20
E
DE CF
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 7
LED Dimming Driver
YS Case Dimensions
All measurements shown as: in (mm)
NFC
0.88 (2.25)
T-Series LED Driver
0.276 (7.0)
Tunable White
3691099i 8 05.11.20
1.14 (29.0)
2.21 (56.2)
0.40 (10.1)
0.21 (5.4)
0.71 (18.0)
0.16 (4.0)
5.12 (130.0)
0.84 (21.4)
0.87 (22.0)
2.0 (50.8)
0.71 (18.0)
0.24 (6.0)
2.22 (56.4)
0.197 (5.0)
3.0 (76.0)
5.51 (140.0) 5.91 (150.0)
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 8
LED Dimming Driver
T-Series LED Driver
YN Case Dimensions
All measurements shown as: in (mm)
0.8 (20.4)
0.17 (4.2)
0.15 (3.9)
0.55 (14.0)
2.24 (57.0)
Tunable White
3691099i 9 05.11.20
0.36 (9.2)
0.15 (3.9)
0.55 (14.0)
NFC
5.12 (130.0)
0.71 (18.0)
5.51 (140.0) 5.91 (150.0)
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
1.14 (29.0)
0.197 (5.0)
3.0 (76.0)
2.21 (56.2)
Page 9
LED Dimming Driver
Wiring Diagram
To line voltage
Neutral (White) Line / Hot (Black) Ground (Green)
T-Series LED Driver
T-Series LED Driver
Ground
To digital T2 (Purple) link T1 (Purple/White)
C1+ and C2+ are electrically connected inside the driver. This supports the use of common anode loads.
Tunable White
3691099i 10 05.11.20
C1+ (Red)
C1- (Black)
Cool LED String
C2+ (Red)
Warm LED String
C2- (Black)
Tunable White Considerations
Tunable White Capability
· The driver will consume two digital addresses:
Address N controls intensity*
Address N+1 controls color temperature*
· The highest kelvin light source must be connected to channel 1 (cool white).
· The lowest kelvin light source must be connected to channel 2 (warm white).
· The driver can accept LED light sources with a physical CCT value between 1500 K and 6500 K.
· The driver default minimum intensity level is set to 1%. See Tunable White Capability figure to the right for more information.
· Operation below 1% may be acceptable in some applications. The minimum level can be adjusted below 1% through the Quantum software. See the Tunable White Capability figure to the right for understanding the general trade off of dimming range versus color temperature range.
· For optimal tunable white performance, it is recommended to set high-end and low-end logical trims which reduce the overall CCT range to less than the maximum capability of the light source.
Dimming Range
Warmest Achievable Color (CCT of Warm LED String)
100%
Coolest Achievable Color
(CCT of Cool LED String)
10% 1%
200 mA Operating Area
Recommended minimum light level
0.2% 0.1%
1500 mA Operating Area
Color Temperature Range
* This is the default behavior. During commissioning, the system may change the addresses to be non-consecutive.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Page 10
Job Number:
LED Dimming Driver
T-Series LED Driver
Tunable White
Compatible Controls: Lutron T-Series Digital Controls
3691099i 11 05.11.20
Guaranteed performance specifications with the controls listed in the chart below.
For assistance selecting controls, contact our LED Center of Excellence at 1.877.346.5338 or LEDs@lutron.com
Lutron T-Series Compatible Controls
Part Number
120 V~
277 V~
T-Series Loops T-Series Drivers
per Control
per Loop
Total T-Series Drivers per Control
T-Series Energi Savr Node*
QSN-TW
2
32**
64
* Must be used as part of a Quantum system version 3.4 or higher. ** Each T-Series loop is capable of having 64 addresses. Each driver consumes two addresses.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 11
LED Dimming Driver
T-Series LED Driver
Tunable White
T-Series Wiring
3691099i 12 05.11.20
T-Series Digital Link Overview
· The T-Series digital link wiring (T1 and T2) connects the digital ballasts and drivers together to form a lighting control system.
· T1 and T2 (T-Series digital link wires) are polarity-insensitive and can be wired in any topology (e.g., T-tap and daisy-chain).
· Power is supplied to the T-Series digital link from the control system.
T-Series Digital Link Wiring
· Make sure that the supply breaker to the drivers and T-Series digital link supply is OFF when wiring.
· Connect the two conductors to the two driver terminals T1 and T2 as shown.
· Using two different colors for T1 and T2 will reduce confusion when wiring several drivers together.
· There are two sets of T-Series digital link terminal blocks to support daisy chaining the link.
· The T-Series digital link may be wired Class 1 or Class 2. Consult applicable electrical codes for proper wiring practices. Please refer to Lutron Application Note #142 (048162) at www.lutron.com for more information.
· For emergency lighting wiring, please refer to Lutron Application Note #106 (048106) at www.lutron.com
To the T-Series digital link supply and additional drivers
T2 T1
N/C
C2-
T2
C2+
T1
C1-
N/C N/C
C1+
N/C
QwikFig Air
Driver Terminals
T2
T1
N/C
C2-
T2
C2+
T1
C1-
N/C
N/C
C1+
N/C
QwikFig Air
Driver Terminals
Notes
· The T-Series digital link supply does not have to be located at the end of the digital link.
· The Maximum Wire Length table below gives the limits for each of the wires in the T-Series digital link pair.
· The T-Series digital link length is limited by the wire gauge used for T1 and T2 as follows:
Wire Gauge Maximum Wire Length 12 AWG 1000 ft * 14 AWG 1000 ft * 16 AWG 900 ft 18 AWG 550 ft
Wire Size 4.0 mm2 2.5 mm2 1.5 mm2 1.0 mm2 0.75 mm2
Maximum Wire Length 300 m * 300 m * 300 m * 207 m 155 m
* Do not exceed cable lengths of 1000 ft (300 m).
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Job Number:
Page 12
LED Dimming Driver
T-Series LED Driver
Service
Warranty For warranty information, please visit www.lutron.com/driverwarranty
Replacement Parts When ordering Lutron replacement parts, please provide the full model number. Consult Lutron if you have any questions.
Further Information For further information, please visit us at www.lutron.com or contact our LED Control Center of Excellence at 1.877.346.5338 or LEDs@lutron.com
Tunable White
3691099i 13 05.11.20
)Lutron, Lutron, Energi Savr Node, Quantum, QwikFig, and QwikFig Air are trademarks or registered trademarks of Lutron Electronics Co., Inc. registered in the U.S. and other countries.
All product names, logos, and brands are property of their respective owners.
Job Name:
SPECIFICATION SUBMITTAL Model Numbers:
Page 13
Job Number: