MT200 LAWN TRACTOR

1. General Information

LEFT and RIGHT are referenced from the operator's position.

NOTICE: The use of Important and Note in the text shows clarifications, exceptions, or alternatives to the procedures. All language translations of this document derive from the initial English source file.

Recycle all packaging, used oil, and batteries according to applicable government regulations.

Diagram showing directional references [Left], [Right], [Front].

2. Operator Safety

Save These Instructions

Save these instructions for future reference. This manual contains safety information to make you aware of the hazards and risks associated with the product and how to avoid them. It also contains important instructions that must be obeyed during the initial set-up, operation, and maintenance of the product. This product is designed and intended for cutting well maintained grass and is not intended for other purposes. It is important that you read and understand these instructions before you attempt to start or operate this equipment. Make sure that you are fully familiar with the controls and the correct use of the product. Know how to stop the unit and disengage controls quickly.

Slope Identification Guide

1. Use a straight edge at least two (2) feet long (A, Fig. 1). A 2x4 or a straight piece of metal works well.

2. Angle finder tools.

a. Use your smart phone: Many smart phones (B, Fig. 1) have an in-clinometer (angle finder) located under the compass application (app). Or, search an app store for an in-clinometer app.

b. Use angle finder tools: Angle finder tools (C and D, Fig. 1) are available at local hardware stores or online (also called in-clinometer, protractor, angle meter, or angle gauge). Dial type (C) or digital type (D) work, others may not. Read and obey the user instructions supplied with the angle finder tool.

3. Put the two (2) feet long straight edge along the steepest part of the lawn slope. Put the board up and down the slope.

4. Lay the smart phone or angle finder tool on the straight edge and read the angle in degrees. This is the slope of your lawn.

Fig. 1 illustrates methods for measuring lawn slope using a straight edge (A), a smartphone with an inclinometer app (B), or dedicated angle finder tools (C, D).

⚠️ Do not operate on slopes greater than 10 degrees.

Safety Alert Symbol and Signal Words

The safety alert symbol in this manual identifies safety information about hazards that can result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the alert symbol to indicate the likelihood and the potential severity of injury. In addition, a hazard symbol may be used to represent the type of hazard.

• ? DANGER: indicates a hazard which, if not avoided, will result in death or serious injury.
• ❗ WARNING: indicates a hazard which, if not avoided, could result in death or serious injury.
• ⚠️ CAUTION: indicates a hazard which, if not avoided, could result in minor or moderate injury.
• ℹ️ NOTICE: indicates information considered important but not hazard-related.

Safety Decals

The following safety symbols appear on this product. Before you operate the mower, please study them and learn their meaning. IMPORTANT: If the safety decals become worn or damaged, and cannot be read, order replacement decals from your authorized service center.

Safety Instructions

❗ WARNING: Read and follow all safety rules and instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.

IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

General Information

• Read, understand, and follow instructions and warnings in this manual and on the machine, engine and attachments.
• Only allow operators who are responsible, trained, familiar with the instructions, and physically capable to operate the machine.
• Do not carry passengers and keep bystanders away.
• Do not operate the machine while under the influence of alcohol or drugs.

Preparation Before Operating

• Clear the operating area of any objects which could be thrown by or interfere with operation of the machine.
• Keep the area of operation clear of all bystanders, particularly small children. Stop the machine and attachment(s) if anyone enters the area.
• Do not operate the machine without the entire grass catcher, discharge chute, or other safety devices in place and functioning properly. Check frequently for signs of wear or deterioration and replace as needed.
• Wear appropriate personal protective equipment such as safety glasses, hearing protection, and footwear.

Operating

• Only operate the engine in well ventilated areas. Exhaust gases contain carbon monoxide, a deadly poison.
• Only operate the machine in daylight or good artificial light.
• Avoid holes, ruts, bumps, rocks, or other hidden hazards. Uneven terrain could overturn the machine, or cause operator to lose their balance or footing.
• Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.
• Do not direct discharge material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blade(s) when crossing gravel surfaces.
• Do not leave a running machine unattended. Always park on level ground, disengage the blades, set parking brake, and stop engine.
• Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.

Children Specific

• Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.
• Keep children out of the operating area and under the watchful care of a responsible adult other than the operator.
• Do not carry children, even with the blade(s) shut off. Children could fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past could suddenly appear in the mowing area for another ride and be run over or backed over by the machine.

Slope Specific

❗ WARNING: Slopes are a major factor related to accidents. Operation on slopes requires extra caution.

? DANGER: If at rest on an uphill slope, do not shift the tractor into gear and dump the clutch. Doing so can result in a rear overturn (the front tires lift off the ground and the machine flips over backwards).

• Travel in the manufacturer recommended direction on slopes. Use caution while operating near drop-offs.
• Avoid mowing wet grass.
• Do not operate machine under any condition where traction, steering, or stability is in question. Tires could slide even if the wheels are stopped.
• Always keep the machine in gear when going down slopes. Do not coast downhill.
• Avoid starting and stopping on slopes. Avoid making sudden changes in speed or direction. Make turns slowly and gradually.
• Use extra care while operating machine with a grass catcher or other attachment(s). They can affect the stability of the machine.

Fire and Fuel Specific

• Extinguish all cigarettes, cigars, pipes and other sources of ignition.
• Use only an approved fuel container.
• Do not remove fuel cap or add fuel with the engine running or while hot.
• Do not refuel indoors or in enclosed spaces.
• Do not store the machine or fuel container, or refuel, where there is an open flame, spark, or pilot light such as on a water heater or other appliance.
• If fuel is spilled, do not attempt to start the engine and avoid creating any source of ignition until fuel vapors have dissipated.
• To help prevent fires: keep machine free of grass, leaves, or other debris build up; clean up oil or fuel spillage and remove any fuel soaked debris; allow machine to cool before storing.
• Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

Hauling

• Use full width ramps for loading and unloading a machine for transport.

Towing

• Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes.

Service

• Keep machine in good working order. Replace worn or damaged parts.
• Use caution when servicing blades. Wrap the blade(s) or wear gloves. Replace damaged blades. Do not repair or alter blade(s).
• Disconnect spark plug wire(s) and the negative battery cable before making any repairs.

❗ WARNING: Running engine gives off carbon monoxide, an odorless, colorless, poisonous gas. Breathing carbon monoxide can cause headaches, fatigue, dizziness, vomiting, confusion, seizures, nausea, fainting or death.

• Operate equipment ONLY outdoors.
• Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes, or other openings.

3. Assembly Instructions

NOTICE: This lawn tractor is shipped without gas in the engine.

❗ WARNING: If any parts are damaged or missing, do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

❗ WARNING: Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

❗ WARNING: To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug boot from the spark plug when assembling parts.

❗ WARNING: Never operate the tractor without the proper safety devices, guards, and chute in place and working. Never operate the tractor with damaged safety devices. Operating the tractor with missing or damaged parts can result in serious personal injury.

Some parts of your new lawn tractor have not been completely installed for shipping purposes. To ensure safe and proper operation, all parts and hardware must be assembled as instructed below using appropriate tools to ensure proper tightness.

Carefully remove the product and any accessories from the package. Make sure that all items listed in the Packing List are included.

Inspect the product carefully to make sure no damage occurred during shipping.

If any parts are damaged or missing, please call 855-693-2582 for assistance.

Packing List

Assemble the Dashboard Cover

1. Open the engine shroud and install the dashboard cover into place. (Fig. 2)

Fig. 2 shows the installation of the dashboard cover into the engine shroud.

Assemble the Air Duct Ring

1. Open the engine shroud and install the air duct ring into the inside of the engine shroud. (Fig. 3)

Fig. 3 shows the installation of the air duct ring inside the engine shroud.

Assemble the Steering Wheel

1. Align the steering wheel with the steering shaft, slide the steering wheel down the shaft until into position, and secure the steering wheel with the bolt provided to a torque of 15-19 ft-lbs. (Fig. 4)

2. Place the steering wheel cap over the center of the steering wheel, and push downward until it snaps into place.

Fig. 4 illustrates aligning and securing the steering wheel to the steering shaft, and attaching the steering wheel cap.

Assemble the Bumper Bar

1. Position the bumper bar in the front of the tractor. (Fig. 5)

2. Install the bumper bar with the four bolts provided (two on each side) to a torque of 15-19 ft-lbs. (Fig. 5)

Fig. 5 shows positioning and securing the bumper bar to the front of the tractor.

Assemble the Left Deck Anti-scalp Wheel

NOTICE: The bottom of the deck anti-scalp wheels should be positioned approximately 1/8 in. - 1/2 in. off the ground when the mower is at the desired cutting height. This will minimize the chance of scalping the lawn in most situations.

NOTICE: The left and right wheels should be set at the same positions.

NOTICE: The right wheel has already been assembled in the factory.

1. Secure the left anti-scalp wheel with the bolt and nut provided to a torque of 22-26 ft-lbs. (Fig. 6)

Fig. 6 shows securing the left anti-scalp wheel with a bolt and nut.

Assemble the Seat

1. Connect the seat to the mower base with bolts and nuts provided to a torque of 15-19 ft-lbs. (Fig. 7)

2. Adjust the seat position to ensure you are able to fully depress the brake pedal before operating the mower.

3. Connect the seat switch.

To move the seat:

1. Pull back on the seat adjustment lever at the left of the seat.
2. While holding the lever, slide the seat forward or backward to the desired position.
3. Release the lever and make sure the seat is locked in position.

❗ WARNING: Be sure the seat is locked into place before operating the mower. A seat that is not secure can cause the operator to shift and lose control of the mower and result in possible death or serious personal injury.

Fig. 7 illustrates connecting the seat to the mower base and connecting the seat switch.

Connect the Battery

The battery is under the operator's seat. To connect the battery cables, proceed as follows:

1. Attach the positive cable (red) to the positive battery terminal using the bolt and nut to a torque of 2-4 ft-lbs. (Fig. 8)

2. Attach the negative cable (black) to the negative battery terminal using the bolt and nut to a torque of 2-4 ft-lbs. (Fig. 8)

❗ WARNING: When attaching battery cables, always connect the positive cable to its terminal FIRST, and then connect the negative cable.

❗ WARNING: Incorrect connection will cause serious damage to the battery.

Fig. 8 shows connecting the positive (red) and negative (black) battery cables to the battery terminals.

Check/Adjust the Tire Pressure

NOTICE: To ensure that the grass is cut level, the right and left front tires must be set to the same pressure. The same is true for the right and left rear tires.

Recommended tire pressure:

• Set the front tires to 14 psi
• Set the rear tires to 10 psi

Fig. 9 indicates the recommended tire pressures: 14 psi for front tires and 10 psi for rear tires.

4. Features and Controls

The following control symbols appear on this product. Before you operate the mower, please study them and learn their meaning.

Ignition: Controls engine start, run, lights, and stop.

PTO lever (Blade engagement lever): Engages and disengages the mower blades.

Height of cut lever: Adjusts the cutting height of the mower deck.

Drive pedal: Controls forward and reverse speed.

Side discharge chute: Directs grass clippings to the side.

Anti-scalp wheel: Prevents the mower deck from digging into the turf.

Fig. 10 shows the throttle/choke lever.

Fuel tank cap: Location for adding fuel.

Fuel tank fill window: Allows visual monitoring of fuel level.

Brake Clutch: Pedal used for braking and engaging/disengaging drive.

Parking brake pedal: Engages the parking brake.

Fig. 11 is a diagram labeling the tractor's controls: Ignition, PTO lever, Height of cut lever, Drive pedal, Side discharge chute, Anti-scalp wheel, Fuel tank cap, Fuel tank fill window, Brake Clutch, Parking brake pedal, Parking brake lever, Mow-in-reverse button, Gear shifter lever, Seat adjustment lever, Cup holder, Hitch.

5. Operating the Tractor

Read the Operator Safety section before you operate this machine. Make sure that you know the controls and how to stop the unit.

Operating Area

• Know the area where you plan to operate the mower.
• Make sure that the area is free of unwanted material that could be picked up by the blades and thrown.

? DANGER: This machine is capable of throwing objects that could injure bystanders or cause damage to buildings.

• Do not operate the machine without the complete grass catcher, discharge chute, or other safety devices in place and functioning properly. Check frequently for signs of wear or deterioration and replace as needed.
• Clear the operating area of any objects which could be thrown by or interfere with the operation of the machine.
• Move the machine outside, before you start the engine.

❗ WARNING: Engines give off carbon monoxide, an odorless, colorless, poisonous gas. Breathing carbon monoxide can cause nausea, fainting, or death.

• Note all slopes and drop-offs.

? DANGER: Operating on slopes, or near water, or drop-offs can result in loss of control and roll-over.

• Mow up and down slopes not across.
• Reduce speed and be careful on slopes.
• Do not operate on slopes over 10 degrees.
• Give yourself a minimum of two mower widths of clearance around water, retaining walls, or drop-offs.

• Avoid mowing wet grass.
• Do not operate the machine under any condition where traction, steering, or stability is in question. Tires could slide even if the wheels are stopped.
• Avoid starting and stopping on slopes.
• Avoid making sudden changes in speed or direction.
• Make turns slowly and gradually.
• Be careful while operating the machine with a grass catcher or other attachment(s). They can affect the stability of the machine.
• Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes.
• See Towing with the Tractor section
• Make sure that the operating area is clear of bystanders, especially children.

? DANGER: This rider mower is capable of amputating hands and feet.

• Stop the mower when children or others are near.
• Keep children out of the operating area and under the watchful care of a responsible adult.
• Do not carry passengers, especially children, even with the blade(s) shut off. Children can fall off and be seriously injured or interfere with the safe machine operation. Children who have been given rides in the past can suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
• Use care when approaching blind corners, shrubs, trees, or other objects that obscure vision.

Safety Interlock System Tests

This machine is equipped with a Safety Interlock System. Do not attempt to bypass or tamper with the switches and devices.

? DANGER: Mowing in reverse can be hazardous to bystanders. Tragic accidents can occur if the operator is not alert to the presence of children. DO NOT activate the Mow In Reverse (MIR) Option if children are present. Children are often attracted to the machine and the mowing activity.

❗ WARNING: If the machine does not pass the five tests below do not operate the machine. See an authorized service center.

Test 1 -- Engine will NOT crank if:

• Power Take Off (PTO) lever is ENGAGED, OR
• Brake pedal is NOT fully pushed down (parking brake OFF)

Test 2 -- Engine will crank and start if:

• PTO lever is DISENGAGED, AND
• Brake pedal is fully pushed down (parking brake ON).

Test 3 -- Engine will SHUT OFF if:

• Operator rises off seat with PTO lever ENGAGED, OR
• Operator rises off seat with brake pedal NOT fully pushed down (parking brake OFF).

Test 4 -- Mower Blade Stopping Time Check

The mower blades and mower drive belt will come to a complete stop in five seconds after the PTO lever is DISENGAGED. If the mower drive belt does not stop in five seconds, see an authorized service center.

Test 5 -- Mow In Reverse (MIR) Option Check

• The engine will SHUT OFF when reverse travel is attempted with the PTO lever ENGAGED and MIR button NOT depressed while reversing. See Mow In Reverse (MIR) Option section.

Engine

Check and Add Engine Oil

Use Briggs & Stratton Warranty Certified oils for best performance. Other high-quality detergent oils are acceptable if classified for service SF, SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to select the best viscosity for the outdoor temperature range expected.

1. Put the unit on a level surface as shown in Fig. 12.

Fig. 12 shows the tractor on a level surface for checking oil.

2. Stop the engine and remove the key. Make sure that the oil fill area is clean.

3. Remove the dipstick (Fig. 13 & Fig. 14). Wipe clean the remaining oil from the dipstick.

4. Install and tighten the dipstick.

5. Remove the dipstick again, and check the oil level.

6. Make sure that the oil level is at the top of the FULL mark on the dipstick.

7. If the oil level is FULL, install and tighten the dipstick.

8. If the oil level is LOW, add oil into the oil fill tube. (Fig. 14)

9. Wait one minute, and check the oil level again.

10. Install and tighten the dipstick.

Engine oil dipstick

Fig. 13 shows the engine oil dipstick. Fig. 14 shows the oil fill tube and dipstick location.

Fuel Recommendation

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane. For high altitude use, see section below.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE: Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will damage the engine components, which will not be covered under warranty. To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See Storage section. All fuel is not the same. If start or performance problems occur, change fuel providers or brands. This engine is certified to operate on gasoline.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum of 85 octane gasoline is acceptable. For carbureted engines, high altitude adjustment is required to maintain performance. Operation without this adjustment will cause decreased performance, increased fuel consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service Center for high altitude adjustment information. Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.

Add Fuel

❗ WARNING: Fuel and its vapors are extremely flammable and explosive. Always handle fuel with extreme care. Failure to observe these safety instructions can cause fire or explosion which could result in severe burns or death.

When Adding Fuel:

• Stop the engine and let the engine cool at least 3 minutes before you remove the fuel cap.
• Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
• Fill the fuel tank outdoors or in a well-ventilated area.
• Do not overfill the fuel tank. To allow for expansion of the fuel, do not fill above the bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary.
• If fuel spills, wait until it evaporates before you start the engine and avoid creating any source of ignition.
• Use only an approved fuel container.

1. Remove any debris from the fuel cap area.
2. Remove the fuel cap (Fig.15)
3. Fill the fuel tank with fuel. Monitor the level of fuel by looking at the see-through window on the left of the tractor. DO NOT fill above the bottom of the fuel tank neck.
4. Install the fuel cap.

Fig. 15 shows the fuel cap location.

Operating Instructions

Start the Engine

❗ WARNING: Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death.

When you start the engine:

• Make sure that the spark plug, muffler, fuel cap, and air filter are installed correctly.
• Do not crank the engine with spark plug removed.
• If the engine floods, move the throttle to the FAST position and crank until the engine starts.

❗ WARNING: Engines give off carbon monoxide-an odorless, colorless, poisonous gas. Breathing carbon monoxide can cause nausea, fainting, or death. Fire or explosion can cause severe burns or death.

• Start and operate the engine outdoors.
• Do not start or operate the engine in an enclosed area, even if doors or windows are open.

1. Check the oil level. See Check and Add Engine Oil section.
2. Insert the key into the ignition switch.
3. If the blades are engaged, disengage the blades.
4. Fully depress the brake pedal.
5. Move the throttle to the FAST position.
6. Turn the key to the START position and hold until the engine starts. After the engine starts, release the key. It will return to the run position.

NOTICE: In the event of an emergency, turn the ignition switch to the OFF position. This will STOP the engine. See Stop the Engine section.

Using the Throttle/Choke Lever

The throttle / choke lever is located on the left side of the mower's dash panel. When starting the engine that is cold, push the throttle fully forward into the "CHOKE" position. (Fig. 16) The purpose of the choke is to restrict the flow of air so that the fuel-air mixture is made richer (more fuel, less air) which aids in starting the engine. After starting the engine, move the throttle downwards to the FAST position.

NOTICE: When operating the mower with the cutting blade engaged, move the throttle to the FAST position.

Fig. 16 shows the throttle/choke lever position for starting a cold engine.

NOTICE: In the event of an emergency, turn the ignition switch to the OFF position. This will STOP the engine.

Using the Headlights

NOTICE: The headlights will quickly drain the battery if the headlights are left on and the engine is off.

Engine on

1. To turn on the headlights, turn the key from the RUN position to the HEADLIGHT position. (Fig. 17)
2. To turn off the headlights, turn the key from the HEAD LIGHT position to the RUN position.

Engine off

1. To turn on the headlights, turn the key to the HEAD LIGHT position.
2. To turn off the headlights, turn the key to the STOP position.

Fig. 17 shows the ignition switch positions for headlights. Reference symbol explanations in the Features and Controls section on page 13.

Stop the Engine

❗ WARNING: Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop the engine.

1. If the blades are engaged, disengage the blades.
2. Shift into neutral.
3. Move the throttle to the SLOW position.
4. Turn the ignition key to the OFF position. Remove the key.
5. Engage the parking brake.

Driving the Tractor

NOTICE: Do not attempt to shift gears when the mower is in motion. Serious damage to the mower's transmission could result. Always use the brake pedal to bring the mower to a complete stop before shifting.

❗ WARNING: Sharp turns can affect control of the mower. ALWAYS slow the mower before making sharp turns.

NOTICE: First-time operators should become completely familiar with the mower's operation and controls before operating the mower in higher speed positions.

❗ WARNING: Always start the tractor in neutral.

NOTICE: Never force the shift lever. Doing so may result in serious damage to the tractor's transmission.

To move forward or backward:

1. Depress the brake pedal and release the parking brake.
2. Place the shifter lever in either the FORWARD (F) or REVERSE (R) gear.
3. Release the brake pedal.
4. Gradually begin to apply pressure to the drive pedal. The further down the pedal is pushed, the faster the tractor will travel in the desired direction.

NOTICE: If you find it difficult to shift to FORWARD or REVERSE, depress the drive pedal lightly and then shift the gears.

Fig. 18 shows the gear shifter lever positions (Forward, Neutral, Reverse). Fig. 19 illustrates the drive pedal.

Using the Brake

NOTICE: Always use the brake pedal to bring the mower to a complete stop before shifting.

NOTICE: Do not use the brake pedal to control the travel speed of the mower. Doing so will result in premature wear of drive belt.

Depress the brake pedal to slow the mower and bring it to a stop. (Fig. 20)

Fig. 20 shows the brake pedal.

Using the Parking Brake

NOTICE: The parking brake pedal must be depressed to start the engine.

NOTICE: The parking brake must be set if the operator leaves the seat with the engine running or the engine will automatically shut off.

Setting the parking brake:

1. Fully depress the brake pedal.
2. Raise the parking brake lever all the way up into the lock position. (Fig. 21)
3. Release the brake pedal to allow the parking brake to engage.

Releasing the parking brake:

1. Fully depress the brake pedal.
2. Lower the parking brake lever all the way down into the unlock position.
3. Release the brake pedal to allow the parking brake to disengage.

Fig. 21 shows the parking brake lever in the engaged position.

Adjusting the Mower Cutting Height

The height of cut lever is located on the mower's right fender. It is used to change the height of the cutting deck. The height (the blade to the ground) can be adjusted from 1" to 4" (13 height positions). To change the height of cut, move the lever out of the notch, then up or down to the position that is best suited for your application. (Fig. 22)

Fig. 22 shows the height of cut lever.

Adjusting the Deck Anti-Scalp Wheels

NOTICE: The bottom of the deck anti-scalp wheels should be positioned approximately 1/8 in. - 1/2 in. off the ground when the mower is at the desired cutting height. This will minimize the chance of scalping the lawn in most situations.

NOTICE: The left and right wheels should be set at the same positions.

To adjust the wheels:

1. Park the mower on a level surface and engage the parking brake.
2. Stop the engine and remove the key. Allow blades to come to a complete stop.
3. Set the deck to the desired height setting.
4. Remove the bolt and nut holding the wheel in place.
5. Move the wheel to a position that's approximately 1/8 in. - 1/2 in. off the ground.
6. Replace the bolt and nut; tighten securely. Torque nut to 4-6 ft. lbs.
7. Repeat steps 4-5 for the other side.

Mowing

• Stop the blade(s) when crossing gravel surfaces.
• Do not leave a running machine unattended. Always park on level ground, disengage the attachment, set the parking brake, stop the engine, and remove the key.

The PTO lever is located on the mower's right fender. Engaging the PTO lever transfers power to the cutting blades.

To engage the blades:

• Move the lever all the way forward.

To disengage the blades:

• Move the lever all the way backward. (Fig. 23)

❗ WARNING: The engine will STOP when reverse travel is attempted with the PTO lever ENGAGED and MIR button NOT depressed while reversing. See Mow In Reverse (MIR) Option section.

NOTICE: The PTO lever must be DISENGAGED when starting the engine.

? DANGER: This machine is capable of amputating hands and feet, and throwing objects. Failure to obey the safety instructions could result in serious injury or death.

• Only operate the machine in daylight hours or good artificial light.
• Avoid holes, ruts, bumps, rocks, or other hidden hazards. Uneven terrain can overturn the machine or cause the operator to lose their balance or footing.
• Do not direct discharge material toward anyone. Avoid discharging material against a wall or obstruction as material may ricochet back toward the operator.

Fig. 23 shows the PTO lever for engaging/disengaging the mower blades.

Mow In Reverse (MIR) Option

? DANGER: Mowing in reverse can be hazardous to bystanders. Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

• Keep children out of the operating area and under the watchful care of a responsible adult.
• Do not carry passengers, especially children, even with the blade(s) shut off. Children can fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past can suddenly appear in the mowing area for another ride and be run over or backed over by the machine.
• Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
• If the machine mows in reverse without engaging the MIR Option, see an authorized service center immediately.

Once The Blades Are Engaged:

1. Depress and hold brake/clutch pedal to stop forward travel.
2. Press and hold M-I-R button. (Fig. 24)
3. Shift gear into reverse.
4. Release M-I-R button.
5. Slowly release brake/clutch pedal.

NOTICE: Remove the key to restrict access to the MIR Option.

Fig. 24 shows the location of the Mow-In-Reverse (MIR) button.

Mowing Tips

• Mowing should always be done with the throttle in the FAST position for optimal cutting results.
• Keep the blades sharp. Jagged cuts increase the likelihood of the tip of the grass blade browning or developing a disease.
• After completing a pass in your lawn, overlap the previous pass by approximately 2 3".
• Change the direction you mow each time you mow to prevent ruts form developing in your lawn.
• Set the mower cut height at the recommended setting for the type of grass in your lawn. Cutting your lawn too short will prevent it from deepening its root system as the grass will use its energy to regrow the grass blades, rather than the root system. A deep root system will allow the grass to find nutrients and water in the soil, especially in periods of drought.
• Raise the mower cut height during the summer or periods of drought.
• Do not cut during the hottest part of the day. Doing so stresses the grass.
• Follow the "1/3 Rule". Take off no more than 1/3 of the grass blade length at a time.
• When cutting long, thick grass, it may be necessary to shift into a lower gear. It may also be necessary to go back over the cut area a second time.
• Do not cut wet grass. The grass will be less likely to clump together and more likely to be standing upright, which will result in a clean, even cut.

6. Maintenance

Before adjustments and repairs:

• Use ONLY the correct tools.
• DO NOT tamper with the governor spring, links, or other parts to increase engine speed.
• Replacement parts must be of the same design and installed in the same position as the original parts. Other parts may not perform as well, may damage the unit, void the warranty, and may result in injury.

❗ WARNING: Improper maintenance, or failure to correct a problem before operation, can cause malfunction and could result in serious personal injury.

⚠️ CAUTION: Before performing any type of maintenance/service, disengage the blades, shut off the engine, and wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and keep it away from the spark plug. Always wear safety glasses while performing any adjustments or repairs.

NOTICE: Refer to engine operator's manual for detailed engine maintenance.

NOTICE: If you are unsure how to perform any of the maintenance items, please contact customer service 855-693-2582 or a qualified service center for assistance.

Maintenance Schedule

RIDER AND MOWER

*Whichever comes first.
**Check the mower blades more often in regions with sandy soils or high dust conditions.

ENGINE

*Whichever comes first.

Cleaning the Tractor

❗ WARNING: Let the tractor to cool for at least five minutes before cleaning. Exercise caution to avoid burns.

⚠️ CAUTION: Do not use pressure washer or garden hose to clean your tractor other than to clean the underside of the deck. It may cause damage to electrical components, spindles, pulleys, bearings, or the engine.

• Clean under the hood and around the engine, including the engine intake screen, exhaust manifold, muffler, and muffler shield.
• Clean the top of the deck and around belts and pulleys.
• Clean around and near the transmission.

NOTICE: Debris can accumulate anywhere on the tractor, especially on horizontal surfaces. Additional cleaning may be necessary when mowing in dry conditions or when mulching.

NOTICE: Fuel leaks/spills, oil leaks/spills, and excess lubrication can also become collection sites for debris. Immediate repair and cleaning up oil or fuel spills can help reduce fire hazards.

NOTICE: Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

Cleaning the Mower Deck

NOTICE: The mower ONLY comes with a washout port block-off plate. A washout port and garden hose quick disconnect are NOT included and must be purchased separately.

A "Universal Deck Wash Kit" that includes a washout port and garden hose quick disconnect can be purchased from The Home Depot. Store SKU #1003930707 or similar.

1. Put the tractor on a smooth level surface.
2. Attach the quick disconnect to the garden hose and then connect to the washout port on the mower deck.
3. Turn the water ON.
4. Start the engine.
5. Set the Height-of-Cut to the lowest position.
6. Engage the Power Take-Off (PTO) to activate the mower blades. The rotation of the blades and the water will clean the bottom of the mower deck. (Fig. 25)
7. Disengage the PTO.
8. Stop the engine.
9. Turn the water OFF.
10. Remove the garden hose and quick disconnect from the washout port.

Fig. 25 illustrates the deck washout port and the process of cleaning the mower deck with water and blade rotation.

Leveling the Cutting Deck

If your lawn appears unevenly cut after using the tractor, the cutting deck may need adjusting. Before deciding that leveling the cutting deck is necessary, make sure the tires are properly inflated to the recommended PSI when mowing.

Before beginning:

1. Make sure the tractor is in neutral.
2. Stop the engine, engage the parking brake, and remove the key.
3. Raise the height of the cutting deck to its highest position.

To make side-to-side adjustment:

❗ WARNING: Tractor blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.

1. Position the blades so that the ends point toward the sides of the mower.
2. Measure the distance from the bottom, outside tip (cutting tip) of the blade to the ground. Measure the left blade's cutting tip to the ground and the right blade's cutting tip to the ground. If the measurements are more than 3/16" off, proceed to the next step.
3. Turn the adjustment nuts up to raise or down to lower the left side of the cutting deck. (a, Fig. 26)

Fig. 26 shows the adjustment nuts (a) for side-to-side deck leveling.

To make front-to-back adjustment:

1. Position the right blade so that the ends now point toward the front and back of the tractor.
2. Measure the distance from the tip of the blade to the ground. For optimal cutting results, the front tip of the blade should be from 1/4 in. to 3/8 in. lower than the rear tip.
3. If front-to-back adjustment is needed, after loosing the outer jam nut, turn the inner adjustment nut clockwise to raise or counterclockwise to lower the front of the cutting deck. (Fig. 27)
4. Measure again to verify the front tip is now 1/4 in. to 3/8 in. lower than the rear tip. If not, continue to adjust and measure until they are.
5. Without moving the inner adjustment nut, re-tighten the outer jam nut to secure the inner adjustment nut in place. (Fig. 27)

Fig. 27 illustrates the adjustment nuts for front-to-back deck leveling.

The deck is properly balanced when both blade tip measurements taken earlier are equal.

Removing the Cutting Deck

❗ WARNING: Tractor blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.

• Removing the deck will make it easier to replace belts, pulleys, and blades.

1. Make sure the tractor is in neutral.
2. Stop the engine, engage the parking brake, and remove the key.
3. Lower the deck to its lowest position.
4. Disconnect the cable spring (a, Fig. 28) that connects the deck to the tractor.
5. Remove the 5 hitch pins, 2 on the left (b and c, Fig. 28), 2 on the right (the same position as shown on left), and 1 on the front (d, Fig. 29) that secure the deck in place.
6. Slip the deck belt off the drive pulley assembly.
7. Slide the deck out from under the tractor.
8. Reverse the process to reattach the deck to the tractor.

Fig. 28 shows the cable spring (a) and hitch pins (b, c) for deck removal. Fig. 29 shows the front hitch pin (d).

Adjusting the Tension in the Deck Belt

If you notice a deterioration in cutting performance, it may be necessary to adjust the tension in the deck cable.

❗ WARNING: Stop the engine, engage the parking brake, and remove the key.

❗ WARNING: Belts on your tractor are subject to wear and should be replaced if any signs of wear are present.

1. The deck cable is set at the factory with no exposed threads showing behind the jam nut (b). (Fig.30)
2. To increase the cable tension, unthread the extension nut (a) 1/8 in.
3. Re-tighten the jam nut up against the extension nut. Now 1/8 in. of exposed threads should be showing behind the jam nut.
4. If this was not adequate, repeat the process above until there is adequate tension in the deck belt.
5. Make sure the cable is not tensioned too tight.

Fig. 30 shows the deck cable adjustment nuts (a, b).

Changing the Deck Belt

❗ WARNING: Stop the engine, engage the parking brake, and remove the key.

1. Remove the deck. Refer to the "Removing the Cutting Deck" section.
2. Remove the two belt protective covers (a, Fig. 31) by removing the six screws that fasten them to the deck.
3. Remove the fixed pulley (b,Fig. 31) and tension pulley (c,Fig. 31).
4. Carefully remove the deck belt from around the pulleys.
5. Reverse the process to reattach a new deck belt to the deck.

Fig. 31 shows the belt protective covers (a), fixed pulley (b), and tension pulley (c) for deck belt replacement.

Changing the Drive Belt

❗ WARNING: Stop the engine, engage the parking brake, and remove the key.

❗ WARNING: If necessary, raise the tractor by placing on a lift or using a jack and jack stands. Make sure the tractor is properly secured and the parking brake is set before proceeding. Failure to properly secure the tractor could cause it to fall, resulting in death or possible serious personal injury.

1. Remove the deck. Refer to the "Removing the Cutting Deck" section.
2. Remove the drive pulley assembly (a, Fig. 32) by removing the bolt that fastens it to the engine output shaft.
3. Remove the two pulleys (b and c, Fig. 32) by removing the nuts that fastens them to the mounting bracket.
4. Slip the belt off the transmission pulley. (d, Fig. 32)
5. Reverse the process to reattach a new drive belt to the tractor.

Fig. 32 illustrates components for drive belt replacement: drive pulley assembly (a), pulleys (b, c), and transmission pulley (d).

Replacing the Cutting Blades

⚠️ CAUTION: Only use replacement blades authorized by the manufacturer of your tractor. Use of blades not authorized is hazardous and may damage your riding mower.

❗ WARNING: Tractor blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them.

1. Shut off the engine, remove the key, and engage the parking brake.
2. Raise the height of the cutting deck to its highest position to allow access to blades.

⚠️ CAUTION: If necessary, raise the mower by placing it on a lift or using a jack and jack stands.

❗ WARNING: If raising the mower to access the blades, make sure the mower is properly secured and the parking brake is set before proceeding. Failure to properly secure the mower could cause it to fall, resulting in death or possible serious personal injury.

3. Use a blade removal tool (not provided) to prevent the blade from turning.
4. Loosen the blade nut by turning it counterclockwise (as viewed from bottom of the mower) using a 24 mm wrench or socket (not provided).
5. Remove the blade nut and blade. (Fig. 33)
6. When replacing or re-installing the blade, be sure to install the blade with the side with a part number stamped in it facing the ground.
7. Thread the blade nut on the shaft and finger tighten.
8. Torque the blade nut down clockwise using a torque wrench (not provided) to ensure the bolt is properly tightened. The recommended torque for the blade nut is 70-85 ft lbs.

❗ WARNING: Ensure blade is properly seated and the blade nut is tightened to the torque specifications above. Failure to properly attach the blade could cause it to come loose and result in possible serious personal injury.

9. Repeat with the second blade.

Fig. 33 shows the blade nut and blade installation, indicating the side with the part number should face the ground.

Sharpening the Blade

1. To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges. Always grind each cutting blade edge equally to maintain proper blade balance.
2. Test the blade's balance using a blade balancer (not provided). Grind metal from the heavy side until it balances evenly.

❗ WARNING: A poorly balanced blade will cause excessive vibration, may damage the tractor, and result in personal injury.

Checking the Tire Pressure

For the correct traction and the best mowing performance, make sure that the front tires are inflated to 14 psi and the rear tires inflated to 10 psi. Also, see "Tire Pressure" in the Specifications section.

NOTICE: There can be a difference in tire inflation pressure from the "Maximum Inflation" shown on the side of the tires.

Battery Maintenance

Replacing the Battery and Cleaning the Battery and Battery Cables

❗ WARNING: When you remove or install battery cables, always disconnect the NEGATIVE (black) cable FIRST and reconnect it LAST. If not done in this order, the positive terminal can be shorted to the frame by a tool.

NOTICE: DO NOT remove or connect the battery cable while the engine is ON.

1. STOP the engine. Remove the key.
2. Disconnect the NEGATIVE (-) cables from the battery first. (Fig. 34)
3. Disconnect the POSITIVE (+) cables from the battery last.
4. Clean the battery surface with baking soda and water.
5. Use a wire brush and terminal cleaner to clean the battery terminals and cable ends.
6. Lubricate the battery terminals with petroleum jelly or non-conducting grease.
7. Install the battery.
8. Connect the POSITIVE (+) cables to the battery first.
9. Connect the NEGATIVE (-) cables to the battery last.

Fig. 34 shows the battery terminals and cables, indicating the order of disconnection (Negative first) and connection (Positive first).

Charging the Battery

❗ WARNING: Keep open flames and sparks away from the battery. Gasses from the battery are very explosive.

A dead battery or one too weak to start the engine can be the result of a defect in the charging system or other electrical components. If there are doubts about the cause of the problem, see an Authorized Service center.

Adjusting the Transaxle Brake

The transaxle is equipped with a brake rotor and brake pads. Over time the brake pads will wear, and it will be necessary to adjust the brake to ensure the brake/parking brake works properly. If you notice that the unit doesn't stop as quickly as it once did or the tractor does not stay in place when the parking brake is engaged, the transaxle brake may need adjusting.

❗ WARNING: Stop the engine, park the tractor on level ground, disengage the parking brake, and remove the key. Make sure the brake rotor is cool before adjusting.

1. Remove the right rear tire to allow easy access to the brake.
2. While rocking the brake rotor (a) back and forth slowly tighten nut (b) until it's not possible to move the brake rotor. (Fig. 35)
3. Loosen nut (b) 2/3 turn and leave as the final setting.
4. As an alternative to a 2/3 turn, use a 0.5mm feeler gauge to set the brake pad 0.5mm off the brake rotor.
5. First loosen the nut (b).
6. Insert a 0.5mm feeler gauge (c), from the side, into the gap between the brake rotor (a) and brake pad.
7. Tighten the nut until the 0.5mm feeler gauge is snug between the brake rotor and brake pad but can still be removed.

Fig. 35 shows the brake rotor (a) and adjustment nut (b) for the transaxle brake.

Checking the Mower Blade Stop Time

❗ WARNING: If the mower blade does not STOP in 5 seconds or less, the clutch must be adjusted. DO NOT operate the machine until the adjustment has been corrected by an authorized service center.

Changing the Engine Oil and Oil Filter

1. Put the unit on a level surface as shown in Fig. 36.
2. Stop the engine and remove the key.

Oil drain plug

Fig. 36 shows the tractor on a level surface for oil change. Fig. 37 shows the oil drain plug and sleeve. Fig. 38 shows the oil filter.

3. Place the oil drain sleeve (included with tractor) under the drain plug. (Fig. 37)
4. Place a collection container below the oil drain sleeve.
5. Remove the drain plug.
6. After the oil has drained, re-install the oil drain plug tightly.
7. Remove the oil filter (Fig. 38) and discard correctly.
8. Before you install the new oil filter, lightly lubricate the oil filter gasket with clean oil.
9. Install the oil filter by hand until the gasket touches the oil filter adapter, then tighten the oil filter 1/2 to 3/4 turns.
10. Refill the engine with new oil.

Checking the engine oil level:

1. Remove the dipstick. Wipe off the remaining oil from the dipstick.
2. Install and tighten the dipstick.
3. Remove the dipstick again, and check the oil level.
4. Make sure that the oil level is at the top of the FULL mark on the dipstick.
5. If the oil level is FULL, install and tighten the dipstick.
6. If the oil level is LOW, add oil into the oil fill tube.
7. Wait one minute, and check the oil level again.
8. Install and tighten the dipstick.

Changing the Air Filter

❗ WARNING: DO NOT start or operate the engine without an air filter as it is a fire hazard.

NOTICE: DO NOT use pressurized air or solvents to clean the air filter. Pressurized air can damage the filter and solvents will dissolve it.

1. Loosen the fasteners and remove the cover. (Fig. 39)
2. Remove the air filter.
3. Clear unwanted material or debris that can get into the carburetor throat.
4. Lightly tap the air filter on a hard surface to loosen debris. If the air filter is dirty, replace it.
5. Install the air filter.
6. Install the cover and tighten the fasteners.

Fig. 39 shows the air filter cover and filter location.

Checking the Spark Plug

❗ WARNING: Unintentional sparking can result in fire or electric shock. Unintentional start-up can result in entanglement, traumatic amputation, or laceration.

When you test for spark:

• Use an approved spark plug tester.
• DO NOT check for spark with the spark plug removed.

NOTICE: Spark plugs have different heat ranges. It is important that the correct spark plug is used, otherwise, engine damage can occur. Replace the spark plug with the same type or equivalent one.

Checking the Spark Plug Gap

Use a spark plug feeler gauge (A, Fig. 40) to check the gap between the two electrodes. When the gap is correct, the gauge will drag slightly as you pull it through the gap. To adjust the spark plug gap, use a spark plug gauge and gently bend the curved electrode. Make sure that you do not touch the center electrode or the porcelain.

Fig. 40 shows a spark plug feeler gauge (A) for checking the spark plug gap.

Install the Spark Plug

Tighten the spark plug with your fingers, and then, tighten it with a wrench.

• 180 in-lbs, OR
• 1/2 turn when you install the original spark plug, OR
• 1/4 turn when you install a new spark plug.

7. Transport

• Empty the fuel tank with a suction pump before transporting the machine. Start the engine and let it run until it has used up all remaining gasoline.
• Close the fuel cap firmly.
• Let the engine to cool down before transporting.
• Use full width ramps for loading and unloading a machine for transport.

• Use extra care when loading or unloading the machine into a trailer or truck. This machine should not be driven up or down ramp(s), because the machine could tip over, causing serious personal injury. The machine must be pushed manually on ramp(s) to load or unload properly.

8. Storage

❗ WARNING: Never store the unit with fuel in an enclosed, non-ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion.

• Store away from furnaces, stoves, water heaters, or other appliances that have pilot lights or other ignition sources because they can ignite fuel vapors.

Tractor

Disengage the Power Take-Off (PTO), set the parking brake, remove the key, and let the machine cool. If you remove the battery, the battery life will increase. Make sure that the battery is in a cool, and dry location, and keep it fully charged. If the battery is left in the unit, disconnect the negative cable.

Fuel System

Fuel can become stale when kept in a storage container for more than 30 days. Each time you fill the container with fuel, add STA-BIL 360 PROTECTIONTM to the fuel as specified by the manufacturer's instructions. This keeps fuel fresh and decreases fuel-related problems or contamination in the fuel system. It is not necessary to drain fuel from the engine when STA-BIL 360 PROTECTIONTM is added as instructed. Before storage, turn the engine ON for 2 minutes to move the fuel and stabilizer through the fuel system.

Before starting the machine after it has been stored:

• Check all fluid levels. Check all maintenance items.
• Do all recommended checks and procedures found in this manual.
• Fully charge the battery.
• Drive the tractor without a load to make certain all the tractor systems are functioning properly.

9. Troubleshooting

❗ WARNING: Before performing any type of maintenance, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting. Always wear safety glasses during operation or while performing any adjustments or repairs.

NOTICE: If you can't solve the problem, take the tractor to an authorized service center for assistance.

Troubleshooting the Tractor

NOTICE: For all other problems, contact an authorized service center.

10. Specifications

Specifications Chart

Power Ratings Disclaimer

The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are derived at 2600 RPM for those engines with "rpm" called out on the label and 3060 RPM for all others; horsepower values are derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher than net engine power and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given the wide array of products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this engine.

11. Disposal

• Gasoline and oil are hazardous waste. Dispose of these materials properly.
• Do not pour gas or oil into the ground or into household garbage. Contact your local recycling authority.
• Some recycling centers will accept gas and oil and will recondition it or recycle it safely. Your city's government official should be able to direct you to the right recycling place. Then, call the recycling location in advance to see if they have any instructions that you'll need to follow.
• If disposing of entire tractor, contact your local metal scrap yard.

12. Warranty

A. REGISTRATION: Please register your Murray MT200 lawn tractor within 60 days of the date of purchase. Go to dayenorthamerica.com/warranty to register.

B. GENERAL PROVISIONS: The warranties described below are provided by Daye, North America, Inc. ("Manufacturer") to the original purchaser of a new Murray MT200 lawn tractor ("Equipment") from The Home Depot. Under this limited warranty, the Manufacturer will repair or replace, at its option, any covered part which is found to be defective in material or workman ship during the applicable warranty term. Warranty service must be performed by a service center authorized by the Manufacturer to service the type of Equipment involved, which will use only new or remanufactured parts or components furnished by the Manufacturer. Warranty service will be performed without charge to the purchaser for parts or labor. The purchaser will be responsible, however, for any transportation of the Equipment to and from the service center's place of business, for any premium charged for overtime labor requested by the purchaser of the Equipment, and for any service and/or maintenance not directly related to any defect covered under the warranties below. If the Equipment is sold to someone else during the warranty term, the limited warranty is transferable to the new owner. After registering, print or save a copy of the warranty number and other relevant information for your records. The warranty number and other relevant information must be transferred to the new owner.

C. WHAT IS WARRANTED: All parts of the Equipment except tires and batteries are warranted for the number of years specified below. Warranty statements required by law covering engine emission-related parts and components, which shall not be less than the engine warranty, are found in the Briggs & Stratton Operator's Manual delivered with the Equipment.

D. WHAT IS NOT WARRANTED: THE MANUFACTURER IS NOT RESPONSIBLE FOR THE FOLLOWING: (1) Any Equipment that has been altered or modified in ways not approved by the Manufacturer; (2) Depreciation or damage caused by normal wear, lack of reasonable and proper maintenance, failure to follow operating instructions, misuse, neglect, negligence, lack of proper protection during storage, or accident; (3) Normal maintenance parts and service; (4) If used for racing or any other competitive activity.

E. SECURING WARRANTY SERVICE: To secure warranty service, the purchaser must (1) Report the product defect to the Murray customer care line at 855-693-2582 and request repair within the applicable warranty term, (2) Present evidence of the warranty start date, and (3) Make the Equipment available to an authorized service center within a reasonable period of time.

F. LIMITATION OF IMPLIED WARRANTIES AND OTHER REMEDIES: The manufacturer shall not be liable for any incidental or consequential damages of any kind resulting from the purchase, use or misuse of, or inability to use the Equipment including incidental, special, consequential or similar damages or loss of profits, or for any claim brought against the purchaser by any other party. There are no express warranties other than those set forth herein. Any warranty implied by state law shall be effective for any product only for the duration of the warranty term. Note: some states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or jurisdiction to jurisdiction.

G. HOME DEPOT WARRANTY: Unless The Home Depot mower protection plan is purchased separately, The Home Depot makes no warranty of its own and The Home Depot has no authority to make any representation or promise on behalf of the Manufacturer, or to modify the terms or limitations of this warranty in any way. https://www.homedepot.com/c/Home_Depot_Protection_Plan_Coverage_Details.

H. WARRANTY PERIOD:

*Attachments/Accessories whether purchased on the same order as the Equipment or purchased separately will be covered by the respective Attachments/Accessories particular warranty term.