Instruction Manual for acer models including: VG270U LCD Monitor, VG270U, LCD Monitor, Monitor
2022-12-05 — Proper service and repair is important to the safe, reliable operation of all series products. The service providers recommended by vender should being ...
File Info : application/pdf, 15 Pages, 975.65KB
DocumentDocumentAcer Monitor VG270U LIFECYCLE EXTENSION GUIDE Contents Table of Contents Important Safety Notice.................................................................................3 1. Exploded Diagram......................................................................................4 2. Wiring connectivity diagram ....................................................................5 3. Mechanical Instruction ..............................................................................6 4. Disassembly and Assembly SOP ............................................................7 5. Troubleshooting .......................................................................................13 6. FRU List .....................................................................................................15 Safety Notice Any person attempting to service this chassis must familiarize with the chassis and be aware of the necessary safety precautions to be used when serving electronic equipment containing high voltage ACER VG270U 3 Important Safety Notice Product Announcement: This product is certificated to meet RoHS Directive and Lead-Free produced definition. Using approved critical components only is recommended when the situation to replace defective parts. Vender assumes no liability express or implied, arising out of any unauthorized modification of design or replacing non-RoHS parts. Service providers assume all liability. Qualified Repairability: Proper service and repair is important to the safe, reliable operation of all series products. The service providers recommended by vender should being aware of notices listed in this service manual in order to minimize the risk of personal injury when perform service procedures. Furthermore, the possible existed improper repairing method may damage equipment or products. It is recommended that service engineers should have repairing knowledge, experience, as well as appropriate product training per new model before performing the service procedures. NOTICE: ! To avoid electrical shocks, the products should be connect to an authorized power cord, and turn off the master power switch each time before removing the AC power cord. ! To prevent the product away from water or explosed in extremely high humility environment. ! To ensure the continued reliability of this product, use only original manufacturer's specified parts. ! To ensure following safety repairing behavior, put the replaced part on the components side of PWBA, not solder side. ! To ensure using a proper screwdriver, follow the torque and force listed in assembly and disassembly procedures to screw and unscrew screws. ! Using Lead-Free solder to well mounted the parts. ! The fusion point of Lead-Free solder requested in the degree of 220°C. 1.1 Product Exploded Diagram 1. Exploded Diagram ACER VG270U 4 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 ODM DESCRIPTION ASSY TRIM PCBA LED BD FFC LCDM MF SCRW SPK SCRW MYLAR WIRE PCBA SPS BD PCBA IF BD SCRW Item 14 15 16 17 18 19 20 21 22 23 24 25 ODM DESCRIPTION FFC LVDS-1 FFC LVDS-2 FFC LVDS-3 FFC LVDS-4 SCRW ASSY SHD PCBA CTRL BD ASSY RC SCRW ASSY CLMN ASSY BASE MYLAR ACER VG270U 5 2. Wiring connectivity diagram There are two types of wiring diagrams for model VG270U. The wiring connectivity position will be different according to the ACTUAL PCBA connector position. Please base on different SKU refer to below diagram. NOTE: INF BD= Interface Board, PWR BD=Power Board, CTRL BD= Control Board 1. SKU with USB. 2. SKU without USB. ACER VG270U 6 3. Mechanical Instruction Tools Required List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed. Tool Description: - working table - Screw-driver: Philips-head screwdriver, Hex-head screwdriver - Knife - glove - cleaning cloth - ESD protection ACER VG270U 7 4. Disassembly and Assembly SOP VG270U 4.1 Disassembly Procedures Preparation before disassemble 1.Clean the room for disassemble 2.Identify the area for monitor 3.Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow; according to the actual condition plan the disassemble layout 4.Prepare the implement, equipment, materials as bellow: 1) working table 2) Screw-driver: Philips-head screwdriver, Hex-head screwdriver 3) knife 4) glove 5) cleaning cloth 6) ESD protection After unplugging the power cord, the power board still have power energe. Please pay attention when disassembling/assembling. S1 Before Disassembling & Assembling, monitor need to be put on the sponge and Disassemble the RC, the Insulation glove must be wore during the process. stand and base Disassemble base and stand from the RC(Rear Case) as picture 1. Unlock RC center screw as picture 2. Disassemble RC from monitor and extract the FFC CTRL from the IF BD as picture 3. PICTURE 1 PICTURE 2 PICTURE 3 S2 Disassemble CTRL BD PICTURE 1 Tear off the adhesive tape of the FFC CTRL from the RC as picture 1. Disassemble the CTRL BD from the RC as picture 2. Disassemble the FFC CTRL from the CTRL BD. PICTURE 2 CTRL BD CTRL BD ACER VG270U 8 S3 Disassemble SPK and Lamp wire Tear off tapes of the SPK wire, extract the SPK wire from the IF BD and disassemble the SPK from the MF as picture 1. Tear off the black tape of the lamp wire, tear off black mylar on SHD and extract the lamp wire from the P/BD as picture 2. Extract the LED wire from the IF BD and tear off the wire from the SHD as picture 3. PICTURE 1 PICTURE 2 PICTURE 3 S4 Unlock 2 TRIM screws and disassemble the ASSY TRIM from the MF as picture 1. Disassemble ASSY Trim Disassemble the LED BD from the Trim and extract the LED wire from the LED BD as picture 2. PICTURE 1 PICTURE 2 LED BD S5 Disassemble SHD and MF. Tear off 4 conductive tapes and 2 Kapton tapes on the FFC wires. Extract 4 FFC wires from the panel as picture 1. Unlock 9 screws from the MF and disassemble the MF from the Pane as picture 2. Extract the lamp wire from the panel as picture 2. PICTURE 1 PICTURE 2 PICTURE 3 ACER VG270U 9 S6 Disassemble I/F BD and P/BD. PICTURE 1 Unlock 6 PCBA screws from the PCBA BD, 1 DP screw and 1 grounded screw as picture 1. Disassemble the I/F BD from the SHD, extract the P/BD wire and 4 FFC LVDS from the I/F BD. Disassemble the P/BD from the SHD. PICTURE 2 PICTURE 3 I/F BD P/BD I/F BD P/BD NOTE: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. ACER VG270U 10 4.2 Assembly Procedures Preparation before assemble: 1.Clean the room for work 2.Identify the area for material 3.Prepare the implement, equipment, materials as bellow 1) working table 2) Screw-driver: Philips-head screwdriver, Hex-head screwdriver 3) Knife 4) Glove 5) Cleaning cloth 6) ESD protection After unplugging the power cord, the power board still have power energe. Please pay attention when disassembling/assembling. S1 Before Disassembling & Assembling, monitor need to be put on the sponge and the Insulation glove must be wore during the process. Assemble I/F BD and P/BD Insert P/BD Wire to P/BD and assemble the P/BD to the SHD. from SHD. Insert 4 FFC LVDS and P/BD wire to the IF BD and assemble the IF BD to the SHD. Lock all PCBA screws, 1 DP screw and 1 grounded screw as picture 2. Assemble the Mylar on the SHD as the picture 3. PICTURE 1 PICTURE 2 PICTURE 3 P/BD S2 Assemble Panel to MF PICTURE 1 Take the Panel and insert lamp wire to panel marked as picture 1. Assemble the MF to the panel and lock 9 screws to the MF as picture 2. Stick 1 piece of adhesive tape on the little connector of lamp wire as picture 3. PICTURE 2 PICTURE 3 ACER VG270U 11 S3 Assemble ASSY TRIM PICTURE 1 Insert the LED wire into the LED BD and assemble the LED BD into the TRIM as picture 1. Assemble the ASSY TRIM on the MF. Lock 2 screws to the ASSY TRIM as the picture 3. PICTURE 2 LED BD S4 Assemble SHD PICTURE 1 Insert 4 FFC LVDS to the Panel and locate the SHD on the Panel as picture 1. Affix 1 Kapton tapes on the left FFC wires. Affix 1 Kapton tape on the 3 right FFC wires. Affix 4 conductive tapes on the FFC LVDS. Insert the big connector of the lamp wire to P/BD as picture 2 and paste 1 mylar on SHD. Tear off the 4 gums on the LED wire, arrange the LED wire and insert the LED wire into the I/F BD as picture 3. PICTURE 2 PICTURE 3 S5 Assemble SPK Assemble the SPK to the MF. Insert the wire of SPK into the I/F BD. Arrange the wire of SPK and stick 4 pieces of black tapes to fasten the wire of SPK on the Panel. Stick 1 piece of black tape to fasten the lamp wire ACER VG270U 12 S6 Assemble the FFC CTRL to the CTRL BD and assemble the CTRL BD to the RC as picture 1. Assemble CTRL BD Stick a piece of adhesive tape to fasten the FFC CTRL on the RC as picture 2. PICTURE 1 PICTURE 2 CTRL BD CTRL BD S7 Assemble the RC, stand and base PICTURE 1 Insert the FFC CTRL to the IF BD and assemble the RC to the MF as picture 1. Lock 1 screw to the RC as the picture 2. Assemble the Stand and Base to Monitor. PICTURE 2 PICTURE 3 NOTE: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal. ACER VG270U 13 TROUBLESHOOTING 5. Troubleshooting Before sending your LCD monitor for servicing, please check the trouble-shooting list below to see if you can self-diagnose the problem. (VGA Mode) Problems Current Status Remedy LED ON Using OSD, adjust brightness and contrast to maximum or reset to their default settings. No Picture LED OFF Check the power switch. Check if AC power cord is properly connected to the monitor. Check if video signal cable is properly connected LED displays amber at the back of monitor. color Check if the power of computer system is ON. Unstable Picture Check if the specification of graphics adapter and monitor is in compliance which may be causing the input signal frequency mismatch. Abnormal Picture Using OSD, adjust RESOLUTION, CLOCK, CLOCK-PHASE, H-POSITION and V-POSITION with non-standard signals. Display is missing, center shift, or too small or too large in display size Using OSD, in case of missing full-screen image, please select other resolution or other vertical refresh timing. Using OSD, in case of missing full-screen image, please select other resolution or other vertical refresh timing. Wait for a few seconds after adjusting the size of the image before changing or disconnecting the signal cable or powering OFF the monitor. Abnormal Sound (Only Audio-Input model) (Optional) No sound, or sound level is too low Check the audio cable with the host PC is connected. Check if the volume setup of the host PC is in minimum position and try to raise the volume level. ACER VG270U 14 (HDMI/DP Mode) Problems Current Status LED ON Remedy Using OSD, adjust brightness and contrast to maximum or reset to their default settings. No Picture LED OFF LED displays amber color Check the power switch. Check if AC power cord is properly connected to the monitor. Check if video signal cable is properly connected at the back of monitor. Check if the power of computer system is ON. Abnormal Sound (Only Audio-Input model) (Optional) No sound, or sound level is too low Check the audio cable with the host PC is connected. Check if the volume setup of the host PC is in minimum position and try to raise the volume level. ACER VG270U 15 6. FRU List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of ACER VG270U. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should c heck the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For AUTHORIZED SERVICE PROVIDERS, your office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional office to order FRU parts for repair and service of customer machines NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose it properly, or follow the rules set by your regional office on how to return it. Category LCD BOARD IF BD ACER DESCRIPTION Description PART NO. LED LCD Panel AUO 27'H QHD None Glare LCDM27W M270DAN02.6Q0 M270DAN02.6 Q0-Z19 LF Z 350nit 12ms 1000:1 KL.27005.026 MAIN BOARD 2H1DP+S PCBA IF BD MI 2H1DP+S VG270U VG270U 55.TEHM3.001 P/ BD CTRL BD POWER BOARD SPK WITH WIRE VG270U PCBA SPS BD MI SPK VG270U 55.TEHM3.002 FUNCTION KEY BOARD WITH BUTTON PCBA CTRL BD MI B277 55.TBTM3.003 LED BD LED BOARD PCBA LED BD SMD B277 55.TBTM3.006Microsoft Word 2019