User Guide for SECURITY BRANDS models including: 14-RTE433, Ridge RTE Request-to-Exit Station, Ridge RTE, Request-to-Exit Station, Exit Station, Station
Resources - Security Brands, Inc.
Ridge RTE - 433-MHz Request-to-Exit Station and Transceiver - Post Mount - Security Brands, Inc.
QUICK START GUIDE 1 Carefully unpack box. 2 Make sure you have all items shown here. (Screwdriver not shown) 1 of 4 Model 14-RTE433 START HERE RTE Unit (includes battery) Transceiver Key Switch Keys (may look different) Lock Key Carriage Bolt ( 4x ) Hex Nut ( 4x ) Hole Plug What's what? Important components labeled Lock For securing interior of RTE Unit Exit Button Triggers gate/door to open Key Switch For enabling and disabling unit (Unit is disabled as shown) BTN 1 BTN 2 RTE Unit Front Panel (Front) RTE Unit Front Panel (Back) Internal wiring not shown for clarity. Pairing Buttons For pairing RTE Unit with Transceiver CR2032 Battery On underside of circuit board Connection Terminals For wiring to compatible AC/DC power source and gate operator or door opener Power LED Indicates whether or not unit has power Relay Status LED Indicates whether relay is active or inactive (Relay is active when lit) Programming Button For pairing Transceiver with RTE Unit Status LED Indicates transmitting status Transceiver Shown with cover removed. Internal wiring not shown for clarity. Programming LED Indicates status of pairing process QUICK START GUIDE 3 Unlock and remove Front Panel of RTE Unit; then using included Carriage Bolts and Hex Nuts, attach unit to pedestal as shown. 4 Using Tek screws, zip ties, or other means of securing, attach Transceiver to inside wall or another surface inside gate operator. 2 of 4 Model 14-RTE433 CAUTION! The Transceiver is not weatherproof and must be mounted inside a weatherproof enclosure. Internal components can be damaged if exposed to the elements. Failure to comply will VOID WARRANTY. WARNING! AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH! ALWAYS CHECK that the GATE PATH IS CLEAR BEFORE OPERATING! REVERSING or other SAFETY DEVICES SHOULD ALWAYS BE USED! 5a Connect Transceiver Gate Operator Timer-to-Close OFF Ridge Transceiver Gate Operator / Door Opener 1224 VAC/DC POWER RELAY 1224 VAC/DC POWER 5b Connect Transceiver Gate Operator Timer-to-Close ON Ridge Transceiver Gate Operator / Door Opener 1224 VAC/DC POWER RELAY 1224 VAC/DC POWER OR NEG. () POS. (+) NC COM NO POS. (+) NEG. () COM RADIO COM FREE EXIT COM REVERSE LOOP COM OPEN STOP CLOSE NEG. () POS. (+) NC COM NO POS. (+) NEG. () COM RADIO COM FREE EXIT COM REVERSE LOOP COM OPEN STOP CLOSE + 1224-VAC/DC Power Source (Not Included) Consult gate operator or door opener manual for exact connections. Terminals vary widely across manufacturers and models. © 2022 Security Brands, Inc. All rights reserved. + 1224-VAC/DC Power Source (Not Included) Consult gate operator or door opener manual for exact connections. Terminals vary widely across manufacturers and models. CAUTION! A closing gate can cause injury to persons or damage to property. ALWAYS USE SAFETY DEVICES! QSG-14RTE433-EN Rev. E (9/2022) QUICK START GUIDE 6a Remove Transceiver cover; then hold down Programming Button on circuit board for 3 seconds and let go. LED will light solid red 6b Remove RTE Unit Front Panel. BTN 1 BTN 2 3 of 4 Model 14-RTE433 6c Hold down both Pairing Buttons until Status LED flashes. Let go of Button 2, and continue holding Button 1 only until Status LED flashes again. 6d Relay on Transceiver should click and Programming LED should go out. Pairing is now complete. LED will go out CHECK THAT THE GATE PATH IS CLEAR BEFORE COMPLETING THIS STEP AS IT TRIGGERS THE RELAY! 7 Press Exit Button on RTE Unit and confirm gate/door opens. (If nothing happens, repeat Step 6. If gate/door is held open, see Troubleshooting section on Page 4.) CHECK THAT THE GATE PATH IS CLEAR BEFORE COMPLETING THIS STEP AS IT TRIGGERS THE RELAY! N INSTALLATION COMPLETE! Your system is ready to use. A The RTE Unit can be disabled and re-enabled at any time by taking the Key Switch Keys and using the Key Switch located below the Exit Button. Unit Enabled (Exit Button active) Unit Disabled (Exit Button inactive) B Transceiver Reset Procedure This procedure is used to unpair all devices from the Transceiver. Step 1 - Remove screws and remove Transceiver cover. Step 2 - Press and hold Programming Button until Programming LED starts to flash. Button must be held for about 30 seconds. Once flashing stops, all devices have been unpaired from Transceiver and reset is complete. Step 3 - Replace Transceiver cover and secure screws. QUICK START GUIDE C Troubleshooting RTE U nit is holding gate/door open IMPORTANT: GATE/DOOR MUST BE CLOSED BEFORE COMPLETING THIS PROCEDURE! Step 1 - Press Exit Button on RTE Unit to close gate/door if it is not already closed. Step 2 - Hold down both Pairing Buttons and pay attention to Status LED. Step 3 - When Status LED flashes twice, continue holding BOTH buttons. Step 4 - When LED flashes twice again, continue holding Button 1 ONLY until Status LED flashes multiple times. Now the RTE unit should only hold the gate/door open momentarily. 4 of 4 Model 14-RTE433 Ridge RTE 14-RTE433 NEED HELP © 2022 Security Brands, Inc. All rights reserved. Call (972) 474-6390 Email techsupport@securitybrandsinc.com We are available MonFri / 8am5pm Central QSG-14RTE433-EN Rev. E (9/2022)Acrobat Distiller 22.0 (Windows)