Trophy Ridge Digital React 3-Pin Sight Manual

Contact Information: 2200 Stringtown Rd., Evansville, IN 47711 | Phone: 800-694-9494 | Fax: 812-467-1245 | Website: www.TrophyRidge.com

General Instructions

Before using the Digital React Sight, charge the battery for at least 8 hours for a full charge. Use the provided charger and cable or a compatible 5.0V 1.0A charger. Charging via car or computer may take approximately 48 hours. A fully charged battery lasts about 48 hours when left on. The backlight turns off after 10 seconds to conserve power.

The battery indicator has 3 bars. When the battery is low, no bars will show, and it will flash, indicating approximately 2 hours of battery life remaining.

The sight enters a power-save mode when on. To reactivate, turn the yardage knob or press any button. The screen will indicate the yardage location of the pin.

NOTE: When plugged in, pressing the power button (PWR) shows the battery indicator. A blinking light indicates charging. The sight charges even when off.

NOTE: To protect the battery, a threshold setting causes the screen to go blank. Reactivate by turning the main adjustment wheel or pressing any button. The screen stays on for 20 seconds, then blanks. This can be repeated up to 10 times. Ensure the sight is charged for optimal battery life.

IMPORTANT: After sighting in, apply the sight tape with the correct markings. If the sight is not charged, the sight tape markings can still be used.

Note: The screen turns blue when a mode or item is selected, indicating that changes can be made.

There are two setup methods: Yardage method (inputting 1st and 2nd pin distances) and Speed method (inputting 1st pin distance and bow speed).

SET UP - Yardage

NOTE: For best results, charge the battery for 8 hours before use. Leave the sight off while charging.

Sight in your vertical or bottom pin at 40 yards using the toolless micro-adjust windage and elevation knobs.

Controls: PWR = Power on/off, MD = Mode, SEL = Select.

BEGIN:

Power on by pressing PWR once. The screen will flash, indicating it's powering up.
The screen will show a number or 'rEA'. If 'rEA' is displayed, press SEL.
NOTE: If a number is displayed, press and hold MD until 'rEA' appears, then press MD to access settings.
The screen will show '1ST'. Press SEL.
'20 yards' will flash blue. Use SEL to increase the number to 40 yards.
NOTE: If no input is received within 10 seconds, the backlight will turn off, but the sight awaits input.
Press and hold SEL. '1ST' will appear, indicating your 40-yard pin is set.
Press MD until '2ND' appears.
Press SEL. The screen will turn purple and display the current distance.
Turn the Main Adjustment Wheel to set the distance to 50 yards.
At 50 yards, shoot your bow and adjust the sight using the main dial until you are on target. The screen may show a different distance.
NOTE: Ensure your pin adjustment is accurately 50 yards, even if the screen displays a different number.
Once your bow is sighted in at 50 yards, press and hold SEL for 2 flashes. Release, and the screen will turn blue.
Press SEL to increase the number or MD to decrease it to adjust the sight reading to 50 yards.
Press and hold SEL for 2 flashes. The screen will turn grey.
Your sight is now calibrated for all distances.

After sighting in yardage markers from 40-100 yards, sight in the 20 and 30-yard horizontal pins. Rotate the sight to its highest up position. Use an Allen wrench to adjust the top pin for 20 yards and the second pin for 30 yards. Do not use windage or elevation knobs for this step.

SET UP - Speed

NOTE: Verify your bow and arrow speed using a calibrated chronograph before proceeding.

Sight in your vertical or bottom pin at 40 yards using the toolless micro-adjust windage and elevation knobs.

Controls: PWR = Power on/off, MD = Mode, SEL = Select.

BEGIN:

Power on by pressing PWR once. The screen will flash, indicating it's powering up.
The screen will show a number or 'rEA'. If 'rEA' is displayed, press SEL.
NOTE: If a number is displayed, press and hold MD until 'rEA' appears, then press MD to access settings.
Once the 1ST distance is set, enter your bow and arrow speed (measured by chronograph).
Press MD until 'SPD' appears.
Press SEL. The number will be blue, representing your bow speed in FPS.
Use SEL to increase and MD to decrease the number to match your bow speed.
Press and hold SEL for 2 flashes. The screen will turn grey.
Your sight is now calibrated for all distances.

NOTE: If your bow is shooting high, increase your bow speed. If it's shooting low, decrease your bow speed.

FCC Compliance Note: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received.

Adjusting for Accuracy - Yardage Setup Adjustments

If your sight requires a higher dialed-in number for accuracy at 50 yards (e.g., 54):

Keep your sight wheel at the 54-yard position.
At 50 yards, press and hold MD until 'rEA' appears (screen turns blue).
Press SEL; '1ST' will appear.
Press MD for the 2nd pin location.
Press and hold SEL to select the 2nd pin location. The screen will turn blue.
Use MD and SEL to adjust this distance to 50 yards. Press and hold SEL to confirm. The screen will flash; release SEL.
Press and hold MD to return to 'rEA'.
Press and hold MD again to return to active mode.
Shoot arrows to confirm accuracy at 50 yards and surrounding distances.

Adjusting for Accuracy - Speed Setup Adjustments

If your sight requires a higher dialed-in number for accuracy at 50 yards (e.g., 54):

At 50 yards, press and hold MD until 'rEA' appears (screen turns blue).
Press SEL; '1ST' will appear.
Press MD twice to see 'SPD'.
Press SEL for Speed settings. The bow speed will flash.
Use MD and SEL to adjust your bow speed.
Press and hold SEL to confirm the speed. The screen will flash; release SEL.
Press MD twice to see 'SPD'.
Press SEL for Speed settings. The bow speed will flash.
NOTE: If your bow is shooting high, increase your bow speed. If it's shooting low, decrease your bow speed.

Settings - Additional Features

The sight has adjustable settings accessible via the settings mode (SEt).

To enter settings mode: Press and hold MD until 'rEA' appears, then press MD again to see 'SEt'. Press SEL to choose 'SEt'.

Adjustable settings include: Precision (Prc), Color (cLr), Brightness (brg), Units of Measure (unt), and Profiles (Pro). Cycle through these by quickly pressing MD.

To exit settings: Press and hold MD for 2 seconds. The screen will flash. Release MD to return to the settings menu (SEt). Press MD again to return to 'rEA' or react setting menu. Press and hold MD for 2 seconds to return to operation mode.

Settings - Change Precision (Prc)

BEGIN: Power on the sight.

If 'rEA' is displayed, press MD, then SEL. If a number is displayed, press and hold MD until it flashes, then press MD to get 'SEt'.
Press SEL to access 'Prc'.
Press SEL again. '1' will be displayed.
Press MD to toggle between 1 and 0.5.
Press and hold SEL to select the desired yardage precision (1 or 0.5). The number will stop flashing and return to 'Prc'.
Press and hold MD to return to 'SEt'. Press and hold MD again to return to the numbers and active mode.

Settings - Change Color (cLr)

BEGIN: Power on the sight.

If 'rEA' is displayed, press MD, then SEL. If a number is displayed, press and hold MD until it flashes, then press MD to get 'SEt'.
Press SEL. 'Prc' will be displayed. Press MD once to go to 'cLr' (colors).
Press SEL. The color options (PINK, AQUA, GREEN, YELLOW, ORANGE, RED, OFF) will be displayed.
Press MD or SEL to cycle through the colors and 'OFF'.
Press and hold SEL to select your desired backlight color. The color name will stop flashing and return to 'cLr'.
Press and hold MD. 'cLr' will flash; release MD to return to 'SEt'.
Press and hold MD. 'SEt' will flash; release MD to return to the numbers and active mode.

Settings - Screen Brightness (brg)

Access 'SEt' as described previously.
Press SEL to access 'Prc'. Press MD twice to go to 'brg' (brightness).
Press SEL. The brightness levels (3, 2, 1, 0) will be displayed.
Use MD and SEL to toggle between the 4 brightness levels. '0' means brightness off.
Press and hold SEL to select the desired brightness level. The number will stop flashing and return to 'brg'.
Press and hold MD. 'brg' will flash; release MD to see 'SEt'.
Press and hold MD. 'SEt' will flash; release MD to return to the numbers and active mode.

Settings - Units of Measure (unt)

Access 'SEt' as described previously.
Press SEL to access 'Prc'. Press MD three times to go to 'unt' (units of measure).
Press SEL. The units (YDS or M) will be displayed.
Use MD and SEL to toggle between Yards (YDS) and Meters (M).
Press and hold SEL to select the desired unit. The letters will stop flashing and return to 'unt'.
Press and hold MD. 'unt' will flash; release MD to see 'SEt'.
Press and hold MD. 'SEt' will flash; release MD to return to the numbers and active mode.
NOTE: If you wish to start over, press and hold the MD button until 'rEA' or 'SEt' appears.

Settings - Orientation (ori)

This section is for troubleshooting if the sight's orientation is incorrect.

Access 'SEt' as described previously.
Press SEL to access 'Prc'. Press MD four times to go to 'ori' (orientation).
Press SEL. The orientation options (rgt - right hand, LFt - left hand) will be displayed.
Use MD and SEL to toggle between 'rgt' and 'LFt'.
Press and hold SEL to select the desired orientation. The letters will stop flashing and return to 'ori'.
Press and hold MD. 'ori' will flash; release MD to see 'SEt'.
Press and hold MD. 'SEt' will flash; release MD to return to the numbers and active mode.

Settings - Profiles (Pro)

Access 'SEt' as described previously.
Press SEL to access 'Prc'. Press MD five times to go to 'Pro' (profiles).
Press SEL. The profile options (PO1, PO2, PO3, PO4, P05) will be displayed.
Use MD and SEL to toggle between the 5 different profiles.
Press and hold SEL to select the desired profile. The letters will stop flashing and return to 'Pro'.
Press and hold MD. 'Pro' will flash; release MD to see 'SEt'.
Press and hold MD. 'SEt' will flash; release MD to return to the 'rEA' mode.
NOTE: After selecting a new profile, you MUST return to the Yardage or Speed setup steps to configure the new profile with appropriate distances and bow speed.
NOTE: Each profile is designed for different hunting seasons or setups, accommodating various bow speeds due to arrow types or weights.

Warnings

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, try correcting it by:

Reorienting or relocating the receiving antenna.
Increasing the separation between the equipment and receiver.
Connecting the equipment to an outlet on a circuit different from the receiver's.
Consulting the dealer or an experienced radio/TV technician.

For additional assistance, contact Trophy Ridge customer service at 1-800-694-9494.

Trophy Ridge Warranty

Trophy Ridge provides a Limited Lifetime Warranty on its products, covering breakage due to defects in materials and workmanship from the date of purchase. Abuse or alteration of the product voids the warranty.

Trophy Ridge's liability is limited to the lesser of the cost of repairing or replacing the broken part, not exceeding the original retail price. Failure to follow installation instructions may void the warranty.

ORIGINAL OWNER: Warranty applies only to the original owner and is not transferable.

ITEMS NOT COVERED: Fiber optic breakage or modification. Some discontinued models may have a fee for rebuild, repair, or modification.

DAMAGE NOT COVERED: Trophy Ridge is not responsible for personal/property harm due to misuse, misapplication, improper installation, or abuse of a Trophy Ridge product. Installation by an experienced, qualified, and competent Pro Shop is strongly recommended for safety.

WE STAND BY OUR PRODUCTS: For warranty service, contact Trophy Ridge Customer Support at 1-800-694-9494 for a return authorization (RA) number and return shipping instructions.

Key Contact Data

Dealer Phone: 800-694-9494

Dealer Fax: 812-467-1245

Web: www.TrophyRidge.com

2L-8000-00