Owner's Manual for AZIMUT models including: KIT DVS-PSS 2024 Sensor Functionality Statement, KIT DVS-PSS 2024, Sensor Functionality Statement, Functionality Statement, Statement
In October 2024, the Direct Vision Standard (DVS), the license to drive an HGV into Greater London, will change significantly. One of the key changes for vehicles weighing
File Info : application/pdf, 20 Pages, 3.57MB
DocumentDocumentSENSOR FUNCTIONALITY STATEMENT KIT DVS-PSS 2024 Content 1. Introduction ............................................................................................................1 2. Product introduction ..............................................................................................2 2.1.Product brief introduction..............................................................................................2 2.2.Parts list..........................................................................................................................3 3. Product func3on introduction................................................................................5 1. func4on introduction ....................................................................................................5 2. Product working logic diagram......................................................................................5 1. DM70MR Display func4on description ........................................................................12 2. Failure mode list and Troubleshooting method............................................................13 3. Others ..........................................................................................................................13 4. Common problems and test maintenance guide ................................................13 4.1.After startup, the system automatically checks. ..........................................................13 4.2.Power failure................................................................................................................13 4.3.Detect range and range anomalies ..............................................................................13 4.4.The system s4ll works aHer ACC OFF............................................................................14 5. Product cleaning and maintenance .....................................................................14 5.1.Camera cleaning time ..................................................................................................14 1. INTRODUCTION Thank you for purchasing a Blind Spot Information and Moving Off Information System with integrated Camera Monitoring System. In order to ensure the correct installation and use of the device, please read the installation instructions and other important information. Disclaimer The content of this manual will be updated from time to time without prior notice; updated content will be added to the new version of this manual. This manual is used as a guide. The photos, charts and illustrations provided in the manual are only for explanation and illustrative purposes. There may be differences with the actual situation, please refer to the actual situation. Safety warning In order to ensure that the system passes DVS/PSS,the installation position of each component is critical. Please be sure to install according to the product assembly instructions; Although this product has the blind spot information function, the driver should take full responsibility for driving, be sure to drive vehicle carefully and pay attention to the surrounding; System detection and sensing components, if obscured will affect the function of the device. Please clean the cameras on the front and sides regularly to ensure normal operation; If the system detects anomalies, or other fault conditions. Please drive carefully to avoid the risk of accidents. For more information, please refer to: https://tfl.gov.uk/info-for/deliveries-in-london/ delivering-safely/direct-vision-in-heavy-goods-vehicles 2. PRODUCT INTRODUCTION 2.1.Product brief introduction In October 2024, the Direct Vision Standard (DVS), the license to drive an HGV into Greater London, will change significantly. One of the key changes for vehicles weighing more than 12 tones, whether from the UK or entering London from overseas, is the minimum star requirement, which will be increased from one to three stars. This adjustment means a greater emphasis on safety, especially for vehicles that do not meet the star rating. In order to be licensed, these vehicles will now need to be equipped with additional safety equipment. Previously, the permit for HGV's additional safety equipment was called a "safety system." However, starting in October 2024, it will be called the Progressive Safe System (PSS).The shift is part of a broader effort to improve safety standards. PSS introduces the latest technological advancements, which means that some operators may need to replace existing equipment with new, more advanced technology. Our DVSUK2 Kit is a perfect entry level solution for the operator who wishes to meet the standards of the Progressive Safe System. 2.2.Parts list A. DM70MR 3channel display B. CS50RA-180 Front Camera C. CS5ORA-180 Side Camera D. AP103A GPS receiver E. AP120 visual LED light 3. PRODUCT FUNCTION INTRODUCTION 1. func3on introduction The Blind Spot Information System (BSIS provides blind spot information and active detection and identification around the vehicle (side. Traffic accidents due to vehicle size and dead line of sight. Blind Spot Information System (BSISis a set of camera AI algorithm to provide drivers with auxiliary information when driving BSIS effectively eliminates vehicle blind spots and reduces accidents due to blind eye angles on the side of vehicles. When the vehicle IS stationary or moving, once a risk object, or a vulnerable road users (VRU enters the detection area, BSIS will provide the driver with an IS (Information Signal information Signal, or WS (Warning Signal warning signal to remind the driver to avoid accidents. The Moving Off Information System (MOIS)is a set of AI technology that provides drivers with active detection and blind spot information ahead of the vehicle. When the vehicle IS stationary or moving, once a vulnerable road user (VRU enters the detection range, the system will provide the driver with an IS (Infor mation Signal) information Signal or WS (Warning Signal) warning signal to remind the driver to avoid accidents. 2. Product working logic diagram 2.1. DVS/PSS BSIS Detect 2.1.1. Vehicle Sta4c V=0Km/h & Brake Signal. Regulation BSIS Warning Type IS DM70MR (Monitor) Detec4on area yellow translucent base map AP120 (LED light) Steady on red below (SIDE) Audio Warning (DM70MR Output) N/A 2.1.2. Vehicle Dynamic (V=0Km/h & No Brake Signal) or (1Km/hV35Km/h). Regulation BSIS Warning Type IS DM70MR (Monitor) Detec4on area yellow translucent base map AP120 (LED light) Steady on red below (SIDE) Audio Warning (DM70MR Output) N/A Regulation BSIS Warning Type WS DM70MR (Monitor) Detec4on area red translucent base map AP120 (LED light) Flashing red below (SIDE) Audio Warning (DM70MR Output) Cau4on. Side Pedestrian. 2.1.3. Vehicle Dynamic (0Km/hV35Km/h) & (No Brake Signal) & (Turning signal is on). Regulation BSIS Warning Type WS DM70MR (Monitor) Detec4on area red translucent base map AP120 (LED light) Flashing red below (SIDE) Audio Warning (DM70MR Output) Cau4on. Side Pedestrian. 2.1.4. Vehicle Dynamic V>35Km/h, Detection Off. 2.2. DVS/PSS MOIS Detect 2.2.1. Vehicle Sta4c V=0Km/h & Brake Signal. Regulation MOIS Warning Type IS DM70MR (Monitor) Detec4on area yellow translucent base map AP120 (LED light) Steady on red above (FRONT) Audio Warning (DM70MR Output) N/A 2.2.2. Vehicle Dynamic (V=0Km/h & No Brake Signal) or (1Km/hV10Km/h). Regulation MOIS Warning Type WS DM70MR (Monitor) Detec4on area red translucent base map AP120 (LED light) Flashing red above (FRONT) Audio Warning (DM70MR Output) Cau4on. Front Pedestrian. 2.2.3. Vehicle Dynamic V>10Km/h, Detection Off. 2.3. DVS/PSS BSIS & MOIS Detect 2.3.1. BSIS & MOIS IS Regulation BSIS + MOIS Warning Type IS DM70MR (Monitor) BSIS & MOIS Detection area yellow translucent base map AP120 (LED light) Steady on red (SIDE & FRONT) Audio Warning (DM70MR Output) N/A 2.3.2. BSIS WS & MOIS IS Regulation MOIS BSIS Warning Type IS WS DM70MR (Monitor) Detec4on area yellow translucent base map Detec4on area red translucent base map AP120 (LED light) Steady on red above (FRONT) Flashing red below (SIDE) Audio Warning (DM70MR Output) N/A Cau4on. Side Pedestrian. 2.3.3. BSIS IS & MOIS WS Regulation MOIS BSIS Warning Type WS IS DM70MR (Monitor) Detec4on area red translucent base map Detec4on area yellow translucent base map AP120 (LED light) Flashing red above (FRONT) Steady on red below (SIDE) Audio Warning (DM70MR Output) Cau4on. Front Pedestrian. N/A 2.3.4. BSIS & MOIS WS Regulation BSIS Warning Type WS DM70MR (Monitor) BSIS & MOIS Detec4on area red translucent base map AP120 (LED light) Flashing red (SIDE & FRONT) Audio Warning (DM70MR Output) Cau4on. Front and Side Pedestrian. 3. DM70MR DISPLAY FUNCTION DESCRIPTION 3.1. Basic func4on : Support 3-channel camera input, CH1 as the PSS side camera, CH2 as the PSS front camera, CH3 as the rear camera, they all support pedestrian detec4on and alarm func4ons. 3-channel video recording func4on is supported, aHer inser4ng an empty TF card and formabng it using the display, the video recording func4on can be performed, the maximum capacity supported is 512G. However, the matching front and side PSS cameras are soundless cameras, so the sound recording func4on is not supported. The display supports touch func4on, user can use the touch func4on to perform func4on sebng, such as: menu opera4on, PSS detec4on zone sebng, etc. PSS detec4on alarm func4on, please see the 4.3. Product working logic diagram 3.2. Menu func4on : Home screen menu BRIGHTNESS:After entering, the screen brightness can be set, there are high, medium, low options. VOLUME: After entering, the system alarm volume can be set, there are high, medium and low options to choose. The default value is Medium. LANGUAGE: After entering, the screen language can be set, there are traditional Chinese, simplified Chinese, English, Spanish optional, the default is English. SYSTEM SETTING: After clicking, the password input screen will appear, and you need to enter a four-digit password. For more information, contact your installer. 4. Failure mode list and Troubleshoo3ng method No camera signal - Front/Rear Troubleshooting method: Check the camera connection. Insufficient illumina4on, detec4on OFF - Front/Rear Troubleshooting mode: None: This alarm is triggered when the scene brightness is too low. Low image quality, detec4on OFF - Front/Rear Troubleshooting method: Check whether the camera lens is dirty and clean the lens. System error, the system will automa4cally restart in 5 seconds Troubleshooting method: Feedback to original factory, provide version number information. 5. Others There is no automatic heating function for the camera, so the lens must be cleaned in rainy and foggy weather, otherwise the camera detection will be affected. 4. COMMON PROBLEMS AND TEST MAINTENANCE GUIDE 4.1.APer startup, the system automa3cally checks. The display send failure message when the system fails. Check all parts of the system, whether the connec4on is normal or dirty 4.2.Power failure Check the power supply voltage. The standard opera4ng voltage is 24V Check whether the power cables and GND are connected correctly. 4.3.Detect range and range anomalies The system meets DVS/PSS test specifica4ons, and the system will take rela4ve speed and vehicle status as reference. Provide IS (Information Signal),or WS (Warning Signal)to alert the driver. 4.4.The system s3ll works aPer ACC OFF Check whether the power cable is connected to the ACC switch 5. PRODUCT CLEANING AND MAINTENANCE Regular cleaning can ensure that the camera lens maintain the best performance, the use of high-quality and safe cleaning agents and soft cloth, can effectively remove stains and debris on the lens. When the camera is automatically heated, it can effectively vaporize the surface of fog and frost and snow. 5.1.Camera cleaning time Inspect the vehicle with the naked eye before using it daily. Clean immediately when accumula4ng dust or dirt. Regular weekly inspec4on, visual observa4on. Clean immediately when accumula4ng dust or dirt Rainy day, frost day, snow day, etc. A failure message is displayed. (Dirty, shielding) Do not use aggressive chemicals or abrasive cleaning products to clean the lens