WalleCube Smart UPS W150 Manual

Read Before Operating

Important Note

Before connecting, operating, and maintaining the device for the first time, please power the device first.

Safety Precautions

Not suitable for and must not be used in the following situations:

• Environments with hazardous gases
• Environments with moisture, dust, dirt, steam, or extreme humidity
• Environments that are prone to mold, insects, or parasites
• Environments with salty air or cooling water, smoke, acid, or other contaminants
• Environments with a pollution level higher than 2 according to IEC 60664-1
• Environments with abnormal vibration, heat sources, or strong electromagnetic interference

Warning

• This device is designed for indoor use only.
• Do not use this device in areas exposed to direct sunlight, liquids, excessive dust, or high humidity.
• Do not use a transformer or voltage regulator to power the device, as this may cause damage to the device.
• The UPS does not have a transformer function; do not use it across voltage ranges. Do not use an adapter with a voltage that does not match the device's power requirements, as this may cause damage to the device.
• Please set the adapter's voltage and current correctly. Incorrect settings may cause the UPS to fail to charge or damage the NAS.
• In case of connecting multiple devices, ensure that the total power output of the power supply adapter exceeds the combined maximum power requirements of all connected devices. The maximum power of each device should be based on the power rating specified on the original power adapter.

Packaging List

The package includes:

• WalleCube Smart UPS Device
• USB Cable
• DC5525 Cable
• DC5521 Male to DC5525 Male Cable
• 4PIN Power Female Cable (Short Cable)
• 4PIN Power Male Cable (Long Cable)
• DC5521 Female to DC5525 Male Cable

Appearance

FRONT

The front panel features a screen and a power/wake-up button. A reboot button is also present.

Diagram Description: A rectangular device with a screen on the front panel and a power/wake-up button. The back panel shows input, output, and USB ports.

• 1: Screen
• 2: Power and wake-up button
• 3: Reboot button

BACK

• 4: Power input port
• 5: Power output port (non-differential)
• 6: USB port

Instructions

Important Note

Before connecting, operating, and maintaining the device for the first time, please power the device first.

Operating

Power On and Power Off

• Power On: Press and hold the power button until you hear a beep.
• Power Off: Disconnect all inputs and outputs from the UPS, then press and hold the power button for 15 seconds to turn it off.

Device Status Indicators

Display Information

The screen displays the following information:

• Vout: Current output voltage
• Iout: Current output current
• battery: Battery charge level (e.g., 100%)
• 29°C: Current battery temperature
• Ibat: Current battery current
• Pout: Current output power
• Battery: Time remaining at current power

Screen Off, Sleep Mode and Transport Mode

• UPS Screen Off: When powered on, the system defaults to screen off mode after approximately 5 minutes.
• UPS Sleep Mode: When not powered on, the system defaults to sleep mode after 10 minutes.
• UPS Transport Mode: After 72 hours in sleep mode, the UPS enters transport mode.

UPS Wake Up

To wake the UPS from screen off or sleep mode, press the power button once.

UPS Restart

To restart the UPS, press the device reboot button.

Device Information

Press and hold the power button for 5 seconds to display device information, including the device's IP address, IMEI number, and the QR code corresponding to that IMEI number. The device is identified as "瓦力方程 WALLECUBE" with an example IP address of 192.168.1.100 and IMEI 1X91A84XE168.

Connecting

Important Note

Before connecting, make sure to select the right cables according to the adapter and NAS. Check the instruction of the NAS if not sure.

4PIN Device Connection

Diagram Description: A 4PIN Power Female cable connects to an adapter. The adapter then connects via a 4PIN Power Male cable to a NAS. A USB cable connects the UPS to the NAS.

DC5521 Device Connection

Diagram Description 1: A DC5521 device is connected via a USB cable to a NAS. An adapter is connected via a DC5521 cable to the UPS.

Diagram Description 2: A DC5521 device is connected via a USB cable to a NAS. An adapter is connected via a DC5521 Female to DC5525 Male cable to the UPS.

Binding and Network

Follow these steps to bind the UPS and configure network settings:

1. Scan the QR code for the WalleCube APP (Android), or search "WalleCube" in the App Store (iPhone).
2. In the APP, click "Add UPS", then scan the device's QR code or enter the device IMEI.
3. On the UPS screen, press and hold the power button for 5 seconds to display a QR code. Scan this QR code with the APP and click "Bind". The APP will then return to the device data page.
4. Click the Bluetooth icon [Bluetooth icon] to connect via Bluetooth. Then, click the Wi-Fi icon [Wi-Fi icon] to configure the network, enter the Wi-Fi password, and connect to the Wi-Fi network.

Cautions

• Connecting Bluetooth requires location, Bluetooth, and nearby devices (local network) permissions. Ensure your phone's location and Bluetooth are enabled.
• The device only supports 2.4G WIFI. If your Wi-Fi network combines 2.4G and 5G bands and you cannot assign an IP address, please separate them.
• When configuring Wi-Fi, position yourself close to the router, disconnect your phone from the Wi-Fi network, and use mobile data for the configuration process.
• If the device fails to assign an IP address, try restarting the device by pressing the reset button and check your router's Wi-Fi encryption type.

Adapter and Parameter

PURPOSE

The UPS needs to know its operating conditions, specifically the voltage and maximum current the adapter provides, to manage power status, NAS power-on, and power restoration.

How to Set Adapter Settings

Connect to Bluetooth, then navigate to "Setting" ➔ "Adapter Settings". Set the voltage and current according to your power adapter specifications.

Example: For a specific adapter, the power adapter voltage is set to 12V and the current is set to 7.5A.

FAQ

• Please use the voltage and current settings accurately. Incorrect configuration may cause the UPS to not power the connected equipment or damage it.
• If the power adapter's output voltage is lower than the specified requirement, lower the power adapter voltage setting accordingly in the APP.
• The UPS does not function as a voltage converter; the input and output voltages are the same. Ensure you use a power adapter suitable for the connected equipment.

NAS Configuration

Check the UPS connection status within your NAS system approximately 5 minutes after connecting. The check paths for some NAS systems are provided below. If your NAS is not listed, consult its manual:

If you encounter any configuration issues within your NAS, please consult the NAS manufacturer's customer service, check the online manual within the WalleCube APP, or send an email to hi@wallecube.com.

Advanced Settings

The WalleCube UPS features an OAT (Online Auto Update) function. WalleCube strives to update and provide more advanced features. Please refer to the online documentation within the WalleCube APP for the latest advanced function instructions.

Specifications

Warranty

This product provides a one-year standard warranty service from the date of purchase. For specific warranty policies, please refer to the sales platform.

Warranty NOT Included

Warranty is not provided for the following circumstances:

• The warranty of this product has expired.
• Damage caused by misuse, improper maintenance, or keeping the product in an inappropriate environment as per the manual.
• Damage caused by the user's own disassembly and modification.
• Product damage caused by unexpected factors or behavior.
• Damage caused by the use of pirated or other illegally authorized software.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

RF Exposure Statement

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.