Instruction Manual for Mooon models including: D076-ZG Smart Cord Dimmer Zigbee, D076-ZG, Smart Cord Dimmer Zigbee, Cord Dimmer Zigbee, Dimmer Zigbee, Zigbee
Mooon Smart Cord Dimmer Zigbee - Black | Zwart | D076-ZG Black
97.43 Item Nr.: D076-ZG Item Description: Zigbee Rotary Cord Dimmer DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH Turn off all power supplying this equitment Use a voltage tester of appropriate rang. Failure to follow these instrucons will result in death or serious injury. WARNING HAZARD OF FIRE Failure to follow these instrucons can result in death, serious injury, or equitment damage. SPECS Rated input voltage: Power range: 220-240Vac, 50Hz 5-50W @ 220-240V LED 10-100W @ 220-240V INC, HAL Type of load: Dimming: Ambient temperature (Ta): Manual Control / APP Control / Voice Control -10¥j+40¥ Dimension: 97.43*31.1*41.8mm Protection: Item weight: Over-temperature, Overload, Over-Current 47.2g WIRING 1. Unscrew the closing screws H 2. Take out the front cover B and the knob A 3. Strip the cable to be connected 4. Connect supply cable to the terminal L and N of the electronic board board. 6. Mount cord anchorage C E C 8. Mount front B and back G , screwing the screws H 9. Stick the rubber sticker I OPERATION 2. MIN. Setting Clockwise to increase the brightness anti-clockwise to decrease the brightness 3. Indicator: to indicate the setting process COMPATIBLE HUB · Homey · Philips Hue · Google Home · Amazon Alexa 31.1 41.8 24.9 ZIGBEE ROTARY CORD DIMMER 15.2 *Dimensions in mm Reset Indicator SUPPORT ZIGBEE CLUSTER 1) Input Cluster - 0x0000: Basic - 0x0003: Identify - 0x0006 - 0x0008 2) Output Cluster - 0x0019: OTA - 0x0004: Groups - 0x0b05 - 0x0005: Scenes SETTING 1. Reset Hold the reset button till the indicator stays in red. Please Note: All configuration will be reset after the device is reset or removed from the network. 2. Include to the Zigbee Network a. Remove the device from a previous Zigbee networkIf it has already been added to one, otherwise pairing will fail. b. Enter your Zigbee hub's app, choose to add lighting and enter the pairing mode. c. Press reset button twice. The indicator starts blinking blue and stay solid for 10s when Succeeds. 3. TouchLink Step 1. If the device is on a ZigBee network, remove the device before enabling TouchLink. Step 2. Press the reset button for 4 times. Step 3. The indicator starts blinking green and stays solid for 10s when pairing is succeds. Time out 15mins. Step 4. Bring the remote within 10cm of the smart dimmer and set the remote into TouchLink commissioning. step 5. The connected light will blink 10 times when TouchLink succeeds. Note: a. When both devices (Dimmer and remote) are not included in the Zigbee Network, each dimmer can link with one remote max. b. When both devices are included in the same Zigbee network, each dimmer can link with max 30 remotes. c. For Philips Hue Hubs and Amazon Echo Plus, add the remote and device to network first then touchlink 4. Find and Bind Step 1.Make sure the device and remote are added to the same Zigbee network. Step 2. Press the reset button for 5 times. Step 3. The indicator starts blinking yellow and will stay solid for 10s. Step 4. Set the remote into find and bind mode and enable it to find and bind commisioning. Please refer to the manual for instructions.Adobe PDF library 15.00 Adobe Illustrator(R) 24.0