Официальный сервисный центр продукции Alphard Group
Owner's Manual for ALPHARD models including: AAB-1200.2D, AAB-1800.2D, AAB-1200.2D Two-Channel Amplifiers, AAB-1200.2D, Two-Channel Amplifiers
Apocalypse AAB-1800.2D
File Info : application/pdf, 24 Pages, 8.85MB
DocumentDocumentTWO-CHANNEL AMPLIFIERS
AAB-1200.2D
AAB-1800.2D
HTTPS://ALPHARD.AUDIO
CLASS D
1. Before installing the amplifier disconnect the battery from the electrical system. 2. To connect the amplifier it is necessary to stretch the power cable from the location of the battery to the place of installation of the amplifier. Select the power cable with the appropriate regulations in AWG (see Table: Selection of the diameter of the power cables) 3. Connect the power supply with the correct polarity. Connect all (+) terminals of the amplifier to the cables stretching from the positive terminal of the battery and all (-) terminals of the amplifier to the cables stretching from the negative terminal of the battery. 4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of the power cable to the holder after connecting the other end to the amplifier. Do not install the fuse(s). 5. Route all signal cables next to each other and separately from the power cables. 6. Connect the wires of RCA input. The input signal power must be between 0.2 V and 6 V. 7. To connect the power wire supply is necessary to use special power cables. 8. Fasten the amplifier properly when installing it in the vehicle. If the component is disconnected during driving, it may cause serious damage to the passengers of the vehicle or another vehicle. It is not recommended to screw the amplifier directly to the metal it can lead to distorsions at the signal outputs. 9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly. Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the light bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive terminal of the battery. When properly connected, the bulb must briefly light up and go out. Now you may connect the positive lead to the (+) of the battery. If the light does not go out, then something is wrong. This will prevent damage to the amplifier in case of reverse polarity and unwanted sparks when connecting. Install the rest of the fuses. 10. To activate the amplifier, it is necessary to apply the positive potential of 12 volts to the control input of the amplifier (REM IN) through a switch or a corresponding control output (REMOTE OUT) with the head unit (HU). 11. LED indicator on front of the amplifier turns blue to indicate that the amplifier is turned on. If the indicator does not light up see chapter "Possible faults and their solutions" for more information. 12. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the sensitivity level of the amplifier up until you hear distortions.
EN 5. WIRING DIAGRAMS
Connect the speaker cables from the positive and negative terminals of the speakers to the respective outputs of the amplifier terminal marked with CH1 / CH2 SPEAKERS OUTPUTS, as shown at the diagram. To connect the power wire supply it is necessary to use special power cables. The fuse is placed in the holder and fixed in the cable cut. One end of the cable is connected to the positive terminal of the battery, the second one to the amplifier terminals marked with +12V. Be sure to use a fuse with the parameters sufficient for use in the system. The length and diameter of the grounding cable must conform to the length and diameter of the cable +12V. Connect one end to the negative terminal of the battery and the other end of the grounding cable to the terminals marked with GND. Connect the head unit (HU) to low-level inputs of the amplifier using RCA cable.
Standard wiring diagram of two-channel amplifier to two speakers. Step 1. Connect the speaker cable from (+) terminal of the amplifier to (+) terminal of the speaker. Step 2. Connect the speaker cable from (-) terminal of the amplifier to (-) terminal of the speaker. Step 3. Repeat the installation sequence Step 1 and Step 2 for each speaker.
1-8 Ohm
1-8 Ohm
Caution!!! The minimum permissible connection load impedance at every single channel is 1 Ohm. For models AAB-1200.2D, AAB-1800.2D the operating voltage is 9-15V.
4
Standard wiring diagram of two-channel amplifier to one subwoofer Step 1. Connect the speaker cable from (+) terminal of the amplifier to (+) terminal of the subwoofer. Step 2. Connect the speaker cable from (-) terminal of the amplifier to (-) terminal of the subwoofer.
min. 2 Ohm
Caution!!! The minimum permissible connection load impedance for bridged connection is 2 Ohm. For models AAB-1200.2D, AAB-1800.2D the operating voltage is 9-15 V.
Standard wiring diagram of two-channel amplifier to battery Step 1. Connect one end of the power cable from (+) terminal of the battery and the second end to the amplifier terminal marked with +12V. Do not forget to protect positive power cable with appropriate fuse. Step 2. Connect one end of the power cable from (-) terminal of the battery and the second end of the grounding cable to the terminals marked with GND. Step 3. Connect one end of the cable to the Remote output terminal at the HU and the second end to the amplifier terminal marked with REM.
Standard wiring diagram of two-channel amplifier to Head Unit Step 1. Connect one end of the RCA cable to the RCA output terminals at the HU and the second end to the amplifier RCA inputs terminals marked with INPUT.
5/FL
1 2 3 4 5 6 7 8 9 10
11 12 13
1. INPUT signal input, RCA jacks 2. CROSSOVER HPF High pass filter (15 Hz 1 kHz at 12 dB/Oct) 3. CROSSOVER LPF low pass filter (50 Hz 20 kHz at 12 dB/Oct) 4. GAIN input signal level adjustment 5. BASS BOOST - bass level adjustment (0-12 dB at 45 Hz) 6. REMOTE input for connection of the bass remote control 7. POWER - LED for operation (blue) 8. CLIP - LED on the clip (orange) 9. PROTECT - LED for protection (red) 10. SPEAKERS OUTPUTS speakers connection terminals 11. +12V power supply terminal (+12V) 12. REM IN connector of remote activation of the amplifier 13. GND grounding supply terminal «-» 14. POWER LED for operation (blue) 15. GAIN input signal level adjustment
Remote control 14 15
Voice coil
4 Ohm 8 Ohm
Total impedance
8 Ohm 16 Ohm
Voice coil
4 Ohm 8 Ohm
Voice coil
4 Ohm 8 Ohm
Total impedance
12 Ohm 24 Ohm
Total impedance
16 Ohm 32 Ohm
Voice coil
4 Ohm 8 Ohm
Total impedance
2 Ohm 4 Ohm
Voice coil
4 Ohm 8 Ohm
Total impedance
1.33 Ohm 2.66 Ohm
Voice coil
4 Ohm 8 Ohm
Total impedance
1 Ohm 2 Ohm
Voice coil
4 Ohm 8 Ohm
Total impedance
4 Ohm 8 Ohm
Model
AAB-1200.2D
Power RMS 4 Ohm* (W) Power RMS 2 Ohm* (W)
580 x 2 780 x 2
Power RMS 1 Ohm* (W)
1 210 x 2
Power RMS 4 Ohm bridged mode* (W)
1 560 1
Power RMS 2 Ohm bridged mode* (W) High pass filter (Hz)
2 420 1 15 - 1 000
Low pass filter (Hz)
50 - 20 000
Crossover (dB/Oct)
12
Bass level adjustment (dB at 45 Hz)
0-12
Frequency response (Hz)
15 - 20 000
Input sensitivity (V)
0.2 - 6
Signal to noise ratio (dB)
100
Damping factor
>260
Input terminal connection (AWG/mm²)
2 / 33.6
Output terminal connection (AWG/mm²)
8 / 8.37
Working voltage (V)
9-15
The simultaneous operation of LPF and HPF
Yes
Minimum permissible load impedance on the single channel (Ohm) 1
Minimum permissible load impedance in bridged mode (Ohm)
2
Size (LWH mm)
215 x 247 73,5
Size (LWH inch)
8.46 x 9.72 2.89
*RMS Power at 14.4 V, THD 1%
AAB-1800.2D 670 x 2
1 020 x 2 1 800 x 2 2 020 1 3 600 1 15 - 1 000 50 - 20 000
12 0-12
15 - 20 000 0.2 - 6 100 > 260 0 / 53.5 8 / 8.37 9-15 Yes 1 2
282 x 247 73.5 11.1 x 9.72 2.89
Deaf Bonce amplifiers are high-quality and technically perfect products. The problems often arise due to improper use, faulty connection of components or lack of power supply of the on-board network.
1) The amplifier does not turn on. Problem solution: Check all the contacts and the presence of 9-15 V at the amplifier terminals. Check whether the control input of the amplifier "REM IN" receives the positive potential of +12 V. 2) Power turns on, but goes into protection (protection indicator lights up) Problem solution: Check if there is a short circuit (fault) on the amplifier output which is connected to the speakers or subwoofers. Make sure that commutation of the voice coils of the subwoofer is correct. The rated impedance of the voice coils should not be lower than the permissible rated load impedance of the amplifier. Check the supply voltage of the amplifier. It must be within the range of 9-15 V. 3) The amplifier turns on but at a high volume it goes in to protection. Problem solution: The amplifier may lack power. Make sure that the rated current of the alternator and the battery capacity is enough to power this amplifier. Check the amplifier for overheating. Check the load impedance. 4) The amplifier is turned on, but there is no sound from the speakers or subwoofer. Problem solution: Check the connection of the amplifier, the integrity of the interconnecting cable, HU, the speakers or the subwoofer.
9. BOX CONTENTS
EN
1. Amplifier 1 pc. 2. Owner's manual 1 pc. 3. Warranty card 1 pc. 4. Remote control 1 pc. 5. Mounting Kit 1 pc. 6. Window decals - 2 pcs.
10. WARRANTY AND MAINTENANCE INFO
Deaf Bonce products are warranted against defects concerning materials and their manufacturing under normal functioning conditions.
While the product is under warranty, defective parts will be repaired or replaced at the manufacturer's discretion. The defective product, along with notification about it, must be returned to the dealer from which it was purchased together with the warranty certificate duly filled in, complete with the original packaging. If the product is no longer under warranty, it will be repaired at the current costs.
Our company does not undertake any liability for damages due to transportation. Our company does not take any responsibility for: costs or loss of profit due to the impossibility to use the product, other accidental or consequential costs, expenses or damages suffered by the customer. Warranty according to laws in force.
For more information visit our website and carefully read warranty card. The manufacturer reserves the right to change design
11. INFORMATION ON DISPOSAL OF THE ELECTRICAL AND ELECTRONIC EQUIPMENT (FOR THE EUROPEAN COUNTRIES WITH SEPARATE WASTE COLLECTION)
9. , . , , . 12 21 , .
. + . , . . .
10. , (REM IN) +12 , (REMOTE OUT) (). 11. LED , . « » . 12. 3/4 ; , , .
, , CH1 / CH2 SPEAKERS OUTPUTS, . , , , , +12V. , . +12V. , , GND. RCA .
. 1. (+) (+) . 2. (-) (-) . 3. 1 2
1-8
1-8
!!! - 1 . AAB-1200.2D, AAB-1800.2D 9-15 .
15
RU
1. (+) (+) . 2 . (-) (-) .
. 2
!!! - 2 . AAB-1200.2D, AAB-1800.2D 9-15 .
1. (+) , , +12V. . 2. (-) , , GND. 3. Remote , , REM.
, 40
1. RCA RCA , RCA , INPUT.
5/FL
16
1 2 3 4 5 6 7 8 9 10
11 12 13
1. INPUT RCA , RCA
2. CROSSOVER HPF (15 1 12 /) 3. CROSSOVER LPF (50 20 12 /) 4. GAIN 5. BASS BOOST (0-12 45 ) 6. REMOTE 7. POWER () 8. CLIP - () 9. PROTECT - () 10. SPEAKERS OUTPUTS 11. +12V (+12) 12. REM IN 13. GND «-» 14. POWER () 15. GAIN
Remote control 14 15
AAB-1200.2D
RMS 4 * () RMS 2 * ()
580 x 2 780 x 2
RMS 1 * ()
1 210 x 2
RMS 4 * ()
1 560 1
RMS 2 * ()
2 420 1
() () (/) ( 45 )
15 - 1 000 50 - 20 000
12 0-12
() ()
15 - 20 000 0,2 - 6
/ ()
100
>260
(AWG/²)
2 / 33,6
(AWG/²)
8 / 8,37
()
9-15
() () ( )
1 2 215 x 247 73,5
( )
8,46 x 9,72 2,89
* RMS 14,4 , 1%
AAB-1800.2D 670 x 2
1 020 x 2 1 800 x 2 2 020 1 3 600 1 15 - 1 000 50 - 20 000
12 0-12
15 - 20 000 0,2 - 6 100 > 260 0 / 53,5 8 / 8,37 9-15 1 2
282 x 247 73,5 11,1 x 9,72 2,89