Owner's Manual for AGT INDUSTRIAL models including: DGS1500, AGT-DGS1500 Wood Chipper, AGT-DGS1500, Wood Chipper, Chipper
File Info : application/pdf, 17 Pages, 705.51KB
DocumentDocumentTable of Contents PRODUCT MANUAL AGT-DGS1500 WOOD CHIPPER WARNING This equipment can not be installed, operated or repaired without reading instructions. Electricity must be hooked up by certified electrician. Do not use this equipment beyond its rated capacity. Missing parts or questions on assembly? Pleasecontact us 1 Part II: Setting Up The Log Splitter Table of Contents PART I: General Safety Rules ........................................................................................................... 3 PART II: Familiar with the Wood Chipper .........................................................................................9 PART III: Operating the Wood Chipper ........................................................................................... 10 PART IV: Maintaining the Wood Chipper ........................................................................................12 PART V: Troubleshooting and Parts List ......................................................................................... 14 Conventions used in this manual WARNING This indicates a hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury. NOTICE This information is important in proper using of your machine. Failure to follow this instruction could result in damage to your machine or property. Additional Information and Potential Changes We reserve the right to discontinue, change, and improve its products at any time without notice or obligation to the purchaser. The descriptions and specifications contained in this manual were in effect at printing. Equipment described within this manual may be optional. Some illustrations may not be applicable to your machine. 2 Part I: General Safety Rules PART I: General Safety Rules Safety Labels Found on Your Unit 2 Part I: General Safety Rules Should make sure the emergency stop switch is available before every use. Or may result in serious injury even death. WARNING Read this Safety & Operating Instructions manual before you use the Wood Chipper. Become familiar with the operation and service recommendations to ensure the best performance of your machine. Propose CAUTION This machine is designed solely to chip wood and must not be used for any other purpose. It should only be used by trained operators who are familiar with the content of this manual. It is potentially hazardous to fit or use any parts other than your dealer parts. The company disclaims all liability for the consequences of such use, which in addition voids the machine warranty. 4 Part I: General Safety Rules Before using the wood chipper NOTICE A Operators must be fully trained before using this machine. BUser Manual is read and understood. C Machine is positioned on level ground, all guards are fitted and in good condition. D Blades are in good condition and secure. All blades are sharpened or replaced in sets. EAll fasteners are checked for tightness. F Only WOODEN materials free of nails etc. are fed into the machine. G Emergency stop wire is rightly connected and the switch is functional. H Fire extinguisher is available on site. When using the wood chipper NOTICE A. Always feed from the side. B. It is better to have a second trained operator within easy reach of the machine. C. Maintain strict discipline at all times and service machine at specified periods. D. Note direction of discharge chute and if necessary note the wind direction to prevent debris from being blown into highway or where it could affect members of the public. E. DO NOT put any part of your body into the in-feed chute while the machine is running. F. DO NOT operate the machine whilst under the influence of alcohol or drugs. G. DO NOT operate inside a building or confined space or Climb on the in-feed chute. Protecting Yourself and Those Around You WARNING This is a high-powered machine, with moving parts operating with high energy. You must operate the machine safely. Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area. Always take the following precautions when using this machine: A. Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and themselves. B. Always wear protective goggles or safety glasses with side shields while using the Wood Chipper to protect your eyes from possible thrown debris. C. Avoid wearing loose clothing or jewelry, which can catch on moving parts. D. We recommend wearing gloves while using the Wood Chipper. Be sure your gloves fit properly and do not have loose cuffs or drawstrings. E. Wear shoes with non-slip treads when using your Wood Chipper. If you have safety shoes, we recommend wearing them. Do not use the machine while barefoot or wearing open sandals. F. Wear long pants while operating the Wood Chipper. G. Keep bystanders at least 50 feet away from your work area at all times. Stop the engine when another person or pet approaches. 5 Part I: General Safety Rules Safety for Children and Pets WARNING Tragic accidents can occur if the operator is not alert to the presence of children and pets. Children are often attracted to the machine and the chipping activity. Never assume that children will remain where you last saw them. Always follow these precautions: A. Keep children and pets at least 50 feet from the working area and ensure they are under the watchful care of a responsible adult. B. Be alert and turn the machine off if children or pets enter the work area. C. Never allow children to operate the Wood Chipper. Safety with Gasoline - Powered Machines WARNING Gasoline is a highly flammable liquid. Gasoline also gives off flammable vapor that can be easily ignited and cause a fire or explosion. Never overlook the hazards of gasoline. Always follow these precautions: A. Never run the engine in an enclosed area or without proper ventilation as the exhaust from the engine contains carbon monoxide, which is an odorless, tasteless, and a deadly poisonous gas. B. Store all fuel and oil in containers specifically designed and approved for this purpose and keep away from heat and open flame, and out of the reach of children. C. Replace rubber fuel lines and grommets when worn or damaged and after 5 years of use. D. Fill the gasoline tank outdoors with the engine off and allow the engine to cool completely. Don't handle gasoline if you or anyone nearby is smoking, or if you're near anything that could cause it to ignite or explode. Reinstall the fuel tank cap and fuel container cap securely. E. If you spill gasoline, do not attempt to start the engine. Move the machine away from the area of the spill and avoid creating any source of ignition until the gas vapors have dissipated. Wipe up any spilled fuel to prevent a fire hazard and properly dispose of the waste. F. Allow the engine to cool completely before storing in any enclosure. Never store a machine that has gas in the tank, or a fuel container, near an open flame or spark such as a water heater, space heater, clothes dryer or furnace. G. Never make adjustments or repairs with the engine running. Shut down the engine, disconnect the spark plug wire, keeping it away from the spark plug to prevent accidental starting, wait 5 minutes before making adjustments or repairs. H. Never tamper with the engine's governor setting. The governor controls the maximum safe operation speed and protects the engine. Over-speeding the engine is dangerous and will cause damage to the engine and to the other moving parts of the machine. If 6 Part I: General Safety Rules required, see your authorized dealer for engine governor adjustments. I. Keep combustible substances away from the engine when it is hot. J. Never cover the machine while the muffler is still hot. K. Do not operate the engine with the air cleaner or the carburetor air intake cover removed. Removal of such parts could create a fire hazard. Do not use flammable solutions to clean the air filter. L. The muffler and engine become very hot and can cause a severe burn; do not touch. General Safety WARNING Operating this Wood Chipper safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe operation can create a number of hazards for you. Always take the following precautions when operating: A. Your Wood Chipper is a powerful tool, not a plaything. Exercise extreme caution at all times. The machine is designed to Chip Woods. Do not use it for any other purpose. B. Know how to stop the Wood Chipper quickly. C. Never operate your unit on a slippery, wet, muddy, or icy surface. Exercise caution to avoid slipping or falling. D. See manufacturer's instructions for proper operation and installation of accessories. E. Never use the machine without ensuring that all guards and shields are in place. F. Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the Wood Chipper. This includes all shields and guards. Modifications to your machine could cause personal injuries and property damage and will invalid your warranty. G. If the machine start to make an unusual noise or vibrate, shut down the engine, disconnect the spark plug wire, keeping it away from the spark plug to prevent accidental starting, wait 5 minutes for engine to cool down, then inspect for damage. Vibration is generally a warning of trouble. Check damaged parts and clean, repair and/or replace as necessary. H. Never tamper with safety devices. Check their proper operation regularly. I. Before performing any maintenance or inspection procedure, shut down the engine, disconnect the spark plug wire keeping it away from the spark plug to prevent accidental starting, wait 5 minutes for machine to cool down. J. Never allow people who are unfamiliar with these instructions to use the Wood Chipper. Allow only responsible individuals who are familiar with these rules of safe operation to use your machine. K. Never overload or attempt to chip woods beyond the manufacturer's recommendation. It could result in personal injury or damage to the machine. L. While using, don't hurry or take things for granted. When in doubt about the equipment or your surroundings stop the machine and take time to look things over. M. Never operate the machine when under the influence of alcohol, drugs, or medication. 7 Part I: General Safety Rules N. Use the machine only in daylight. O. Stay alert for hidden hazards or traffic. P. Keep all nuts and bolts tight and keep the equipment in good operating condition. A Note to All Users List of warnings and cautions cannot be all-inclusive. If situations occur that are not covered by this manual, the operator must apply common sense and operate this WOOD CHIPPER in a safe manner. Contact the dealers for assistance in your area. 8 Part II: Familiar with the Wood Chipper PART II: Familiar with the Wood Chipper It may be helpful to familiarize yourself with the controls and features of the Wood Chipper. If you have any question, please contact the dealers in your area. TECHNICAL SPECIFICATIONS Engine Power Chipper Capacity Wood Diameter Permitted wood width Chipper Blade Tire Overall Height Overall Length Width weight Roller Max RPM DR-GS-150SH 13HP/14HP/15HP four strokes Gasoline/petrol 4CBM/hour to 6CBM/hour diameter 100mm 300mm twin reversible blades 6.5-84.0-84.8-8 1800mm 2700mm 1070mm 280kgs/330kgs 3600 7 Part III: Operating the Wood Chipper PART III: Operating the Wood Chipper It may be helpful to better familiarize yourself with the features of your Wood Chipper before beginning the steps outlined in this chapter. WARNING A. Read and understand all instructions, safety precautions, and/or warnings listed in "PART I: General Safety Rules" before operating the WOOD CHIPPER. If any doubt or question arises about the correct or safe method of performing anything found in this manual, please contact the dealers in your area. B. When operating the Wood Chipper, make sure you are standing in the safe operating area (OPERATOR ZONE). You must stay in the safe operating area at all times when the ram is in motion (whether extending or retracting). Never place any part of your body into a position that causes an unsafe operating condition. C. Before loading and operating the Wood Chipper, always wear protective gear, including safety goggles, hearing protection, tight-fitting gloves without draw strings or loose cuffs, and steel-toed shoes. D. Knowing the correct and incorrect methods of Chipping woods. Never using an incorrect or unsafe method. Starting 1. Make sure the stop bar or stop button not activated. 2. Position your Wood Chipper on flat, dry ground, and then stop the front wheel with brake, make sure the machine cannot be moved. 3. Make sure the fuel shut-off valve is in the "ON" position. 4. Move the choke control lever to the "CHOKE" position (should only be needed if the engine is cold). 5. Move the throttle control lever to the "FAST" position. 6. Recoil Start: Turn the Ignition Switch to the "On" position. Grasp the recoil starter handle and slowly pull until you feel resistance. Let the cord retract a little bit then pull the cord rapidly to start the engine. One or two pulls usually starts the engine. 7. Electric Start: Turn and hold the Key in the start position until Engine starts then let the Key return to run position. 8. Move the choke control lever (if used for cold engine) slowly back to the "RUN" position when the engine is running well. 9. If the Wood Chipper has not been running (cold engine), warm up the engine by running the engine at half throttle for 3 to 4 minutes, then advance the engine throttle control to the maximum speed. 8 Part III: Operating the Wood Chipper Stopping PUSH THE EMERGENCY STOP BAR OR STOP BUTTON TO STOP. OR: 1. Move the Throttle Lever to IDLE. 2. Recoil Start: Turn the Ignition Switch to the OFF position. 3. Electric Start: Turn the Key to the OFF position. Operator Zone Wood Chipping NOTICE Woods' and branches' diameter should be no bigger than 120mm. WARNING Do not place your hands into the chute when loading. This is a very UNSAFE method and could result in injury to your hands. Do not reach or step across the rail while the Wood Chipper is running. This is a very UNSAFE method which could cause personal injury, even death. When Blocked If the Roller stops while chipping woods or branches, the engine should be stopped, and take out the woods which stuck the roller, and then restart the engine, and chip again. 11 Part IV: Maintaining The Wood Chipper PART IV: Maintaining the Wood Chipper Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug. Disconnect the Battery Terminals (Electric start only). Regular Maintenance Checklist Procedure Check engine oil level Check general equipment condition Check belts Check tire pressure Clean engine exterior and cooling Change Engine Oil Replace air filter Replace spark plug Before Each Use First time 5hours Every 3 Hours Every 25 Hours Every 100 Hours Engine Service Refer to the engine manufacturer's user manual for engine maintenance. 10 Part IV: Maintaining The Wood Chipper Lubrication NOTICE All Bearings of your Chipper are sealed units and should have sufficient lubricant to last the life of your machine with normal use. 13 Part VI: Troubleshooting and Parts List PART V: Troubleshooting and Parts List Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact the dealers in your area. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug. Troubleshooting Table SYMPTOM The engine won't start. (Please refer to the engine user manual for engine-specific procedures.) The engine lacks power or is not running smoothly. (Please refer to the engine user manual for engine-specific procedures.) Engine smokes. (Please refer to the engine user manual for engine-specific procedures.) POSSIBLE CAUSE Is the ignition switch in the "ON" position? Is the fuel shut-off valve on? Are you using fresh, clean gas? If the gas is old, change it. Use a fuel stabilizer if you keep gas longer than 30 days. Is the spark plug clean? If the spark plug is dirty or cracked, change it. If it's oily, leave it out, hold a rag over the plug hole and pull the recoil cord several times to blow out any oil in the cylinder, then wipe off the plug and reinsert it. Check that the Throttle Lever is in the "Run" position. Is the air filter clean? If it's dirty, change it following the procedure in the engine manufacturer's owner's manual. Is the spark plug clean? If it's fouled or cracked, change it. If it's oily, leave it out, hold a rag over the plug hole and pull your recoil cord several times to blow out any oil in the cylinder, then wipe off the plug and reinsert it. Are you using fresh, clean unleaded gas? If it's old, change it. Use a fuel stabilizer if you keep gas longer than 30 days. Does your engine have the right amount of clean oil? If it's dirty, change it following the procedure in the engine manufacturer's owner's manual. Check the oil level and adjust as needed. Check the oil level and adjust as needed. Check the air filter and clean or replace if needed. You may be using the wrong oil--too light for the temperature. Refer to your Engine Owner's Manual for detailed information. Clean the cooling fins if they're dirty. 14 Part VI: Troubleshooting and Parts List Machine does not seem to have full chipping power. The belts may be too loose and slipping. Adjust or replace belts as need. Explosion View and parts list No. Description No. Description No. Description 1 Main body 2 Wheel 3 Wheel cover 4 Blade system assy. 5 Filter net 6 Door plate 7 Anvil 8 Engine plate 9 Rear plate 10 F208 bearing base 11 Engine pulley 12 Disk pulley 13 Belt 14 Belt cover 15 Tow bar 16 Tow Hitch 17 Foot 18 Rubber pad 19 Tool box(opt.) 20 Tool box cover(opt.) 21 Discharge 22 Wheel axis 23 Battery box(opt.) 24 Battery(opt.) 25 Clover bolt 26 Switch 27 Switch plate 28 Spring 29 Chain 57 30 Pin 58 31 Engine 59 32 Connect frame 60 33 Belt cover bottom part 61 34 Tension assy. 62 35 Tension base 63 36 Deflector 64 37 Infeed top part 65 38 Infeed bottom part 66 39 Emergency bar 67 40 Arm 68 41 Buckle 69 42 Restrict plate 70 43 Outer Ring 71 44 Left ring 72 45 Right ring 73 46 Switch cover 74 47 Spring frame 75 48 Rubber plate 76 49 Rubber fitting bar 77 50 M10*30 bolt 78 51 Pin 4*32 79 52 Spring washer 10 80 53 Spring washer 12 81 54 Spring washer 16 82 55 Spring washer 8 83 56 flat washer 12 84 flat washer 16 flat washer 10 flat washer 8 flat washer 10 flat washer 8 Spring washer 40 Keyway 6*50 Keyway 10*36 Hex bolt M12*25 Hex bolt M12*55 Hex bolt M12*30 Hex bolt M16*70 Hex bolt M10*55 Hex bolt M12*80 Hex bolt M12*100 Hex bolt M10*70 Hex bolt M10*80 Hex bolt M8*25 Hex bolt M8*20 Hex flange bolt M8*16 Hex nut M12 Hex nut M10 Hex flange nut M8 Hex lock nut M10 Hex lock nut M12 Hex lock nut M16 Hex lock nut M8 Hex slot nut M24 15 Part VI: Troubleshooting and Parts List 16 Part VI: Troubleshooting and Parts List 17WPS 文字