Installation Guide for ELCOP models including: RD350VAAU, Rotary Controlled LED Dimmer 350 VA
Index of /wp-content/uploads/2021/02/
Rotary LED Dimmer 350VA | Elcop – Zippy Electrical Suppliers
File Info : application/pdf, 2 Pages, 5.42MB
DocumentDocumentInstallation Guide 2.0 Description The LED Dimmer is a rotary controlled, modular dimmer mechanism rated at 350 VA. Up to six dimmer mechanisms can be installed in a plate! Designed for LED lamps, the unit utilises powerful and sophisticated dimming technology to provide control. The LED Dimmer also incorporates over-current and thermal fuse cutoff (non-recoverable) protection devices and is capable of withstanding persistent short circuit conditions. 3.0 Features Table of Contents Section .................................................................... · Modular dimming mechanism. · Two-wire phase control wall plate dimmer. · Soft-start for lamp and driver life. · Provide optimised dimming of LED based lamps and drivers. · Compatibility with incandescent lamps,240V halogen lamps, Low voltage halogen lamp with dimmable electronic transformer, etc · Wall or architrave mounting options. · Wide range of plate styles and colour variants available. · Suitable for new installations or retro-fit applications. · Inbuilt Over-Current and Over-Temperature protection. · Full short circuit protection. · Immune to high frequency (ripple) signal injection on mains supply. · Complies with Australian and International EMC Standards. 1.0 Product Range .................................................................... 2.0 Description .......................................................................... 4.0 Electrical Specification 3.0 Features .............................................................................. 4.0 Electrical Specification......................................................... 5.0 Load Compatibility ............................................................... 6.0 Wiring Diagram .................................................................... 7.0 Installation ............................................................................ 8.0 Warranty Statement.............................................................. 1.0 Product Range Product No. Description AU-RD350VA Rotary Controlled LED Dimmer,350 VA Parameter Value Nominal Operating Voltage 220-240 V ac Nominal Operating Frequency Maximum Load 50 Hz 350 VA @1 Gang Derate for multi-gang applications Minimum Load 10 VA Dimming Technique Mounting Centres Trailing Edge Phase Control 84mm Australian Pattern Plate Safety Compliance AS/NZS 3100, AS/NZS 3133, IEC 60669-2-1 EMC Compliance AS/NZS CISPR15, IEC 60669-2-1 (26.1, 26.2), IEC 61000-3-2 (Excepting when used in conjunction with Electronic loads) Specifications Typical @ 240 V ac 25 ¥ Suitable for Indoor Use Only No User Serviceable Parts Inside 5.0 Load Compatibility AU-RD350VA Load Symbol Compatible Loads Maximum Load Minimum Load Dimmable LED Lighting 150 W 10 W 7.0 Installation To connect the required lighting loads, then follow the following steps: Step 1 Leave the dimmer connected, but remove the dimming knob from the dimming shaft Step 2 Turn the dimmer shaft anti-clockwise until the available installation level is reached. Incandescent Lighting 240 V Halogen Lamps 350 W Low Voltage Halogen Lightingwith Electronic Transformers 350 VA 10 W 10 VA 6.0 Wiring Diagram Step 3 Align the plane on the front face of the dimmer with the plane on the inside of the dimmer knob Step 4 Push the dimmer knob back onto the shaft such that the plane remain aligned Live Neutral One-Way Wiring Diagram Live Neutral Two-way Wiring Diagram NOTE: · The LED dimmer series are designed for One-Way or Two-Way operation as above diagrams. · Two or more dimmers cannot be connected in parallel or series to control the same load from two different locations. · Dimmer Mechanism wiring is NOT polarity sensitive 8.0 Warranty Statement 1. This product is guaranteed against faulty workmanship and materials for a period of two years from the date of installation. 2. This warranty is expressly subject to the product being installed, wired, tested,operated and used in accordance with the manufacturer's instructions. It is illegal for persons other than an appropriately licensed electrical contractor or other persons authorised by legislation to work on the fixed wiring of any electrical installation. Penalties for conviction are severe!Sejda 3.2.19 (www.sejda.org) Adobe PDF library 9.90