myTOUCH SMART Indoor Digital Simple Set Plug-In Timer

Product Overview

This document provides instructions for the myTOUCH SMART Indoor Digital Simple Set Plug-In Timer. It guides users through initial setup and programming custom on/off times for lights and appliances.

Timer Interface Description

The timer features a digital display and several control buttons:

• Clock/Set Buttons: Used for setting the current time and programming modes.
• My on/off time Buttons: Used to set custom on and off times for automated operation.
• Reset Button: Clears all current times and schedules, resetting the timer to factory defaults. This button is typically located in a small recessed hole and may require a toothpick or pencil to press.
• Up [↑] and Down [↓] Arrows: Used to scroll through and set the current time, as well as program custom on/off times.
• Active Program Indicator Arrow: Appears on the screen when a program is set, indicating that the timer is active.
• AM/PM Indicator: Displays whether the set time is AM or PM.

Figure 1: Diagram showing the timer's buttons and indicators.

I. Initial Setup

1. Setup

   If the display is not visible or numbers are difficult to read, plug the timer into an outlet and allow it to charge for one hour. After charging, press the reset button [reset-button] located in the lower left corner using a toothpick or pencil.

2. Set the Time

   Use the Up [↑] and Down [↓] arrows to set the current time. Note the AM or PM designation. For daylight saving time adjustments, use the Up [↑] and Down [↓] arrows to change the time by one hour.

II. Programming

1. Choose Your Custom "my On Time"

   Press the "my on time" button. The default time will flash. Use the Up [↑] and Down [↓] arrows to set your desired on time. If the set "my on time" is earlier than the current time, the timer will activate on the following day at the scheduled time.

   Once the "my on time" is set, wait 5 seconds, press "my on time" again, or press "my off time" to proceed to setting the off time.

2. Choose Your Custom "my Off Time"

   Press the "my off time" button. The default time will flash. Use the Up [↑] and Down [↓] arrows to set your desired off time.

   Once the "my off time" is set, wait 5 seconds, press "my off time" again, or press the "my on time" button to set the next on time.

   Note: When a "my on" or "my off" time is set, the active program indicator arrow will appear on the screen next to the corresponding button.

Default "My On" / "My Off" Times

• 5:00 p.m.
• 6:00 p.m.
• 12:00 a.m.
• 6:00 a.m.

Important Information and Warnings

FCC Statement

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3(B)/NMB-3(B)

WARNING

RISK OF ELECTRIC SHOCK

• Plug directly into an electrical outlet.
• Do not use in wet locations.
• Fully insert plug.
• Use indoors only.
• Unplug timer before cleaning.
• Keep children away.

RISK OF FIRE

• Do not use to control appliances that contain heating elements (cooking appliances, heaters, irons, etc.).
• Do not exceed electrical ratings.
• Do not use with extension cords.

Manufacturer and Warranty Information

MADE IN CHINA

Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.

This Jasco product comes with a 1-year limited warranty. Visit www.byjasco.com for warranty details.

Questions? Contact Jasco Products Company LLC at 1-800-654-8483 between 7:00 AM - 8:00 PM CST.

Specifications:

• 125V~50/60Hz
• Maximum load: 15A 1875W resistive, 5A 625W tungsten, 1/2HP
• Suitable for Indoor Use only.
• Works with dimmable LED and CFL bulbs.

Model Number: 36253

Version: 01 9/28/16