Instruction Manual for DynaLabs models including: DYN-I-9000 Triaxial MEMS Gyroscopes, DYN-I-9000, DYN-I-9000 Gyroscopes, Triaxial MEMS Gyroscopes, MEMS Gyroscopes, Triaxial MEMS, Triaxial Gyroscope, Gyroscope
30 apr 2022 — Disclaimer. Dynalabs Ltd. provides this publication "as is" without warranty of any kind, express or implied, including but not limited to, ...
Manuals & Datasheets – Dynalabs
File Info : application/pdf, 9 Pages, 383.83KB
DocumentDocumentModel DYN-I-9000 [g|°/s]: 2|75, 4|75, 8|75, 10|75, 20|75, 40|75, 50|75, 100|75, 200|75, 500|75 [g|°/s]: 2|150, 4|150, 8|150, 10|150, 20|150, 40|150, 50|150, 100|150, 200|150, 500|150 [g|°/s]: 2|300, 4|300, 8|300, 10|300, 20|300, 40|300, 50|300, 100|300, 200|300, 500|300 [g|°/s]: 2|900, 4|900, 8|900, 10|900, 20|900, 40|900, 50|900, 100|900,200|900, 500|900 Product Manual All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Product Support If at any time you have questions or problems with the DYN-I-9000 sensors, please contact a Dynalabs engineer at: Phone: E-mail: +90 312 266 33 34 (9 a.m. to 5 p.m., UTC +3) info@dynalabs.com.tr Warranty Our products are warranted against defective materials and workmanship for one year. Defects arising from user errors are not covered by the warranty. Copyright All copyrights of this manual belonging to Dynalabs products are reserved. It cannot be reproduced without written consent. Disclaimer Dynalabs Ltd. provides this publication "as is" without warranty of any kind, express or implied, including but not limited to, the implied warranties of merchantability or fitness for a particular purpose. This document is subject to change without notice, and should not be construed as a commitment or representation by Dynalabs Ltd. This publication may contain inaccuracies or typographical errors. Dynalabs Ltd. will periodically update the material for inclusion in new editions. Changes and improvements to the product described in this manual may be made at any time. 2 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Table of Contents 1) Introduction..........................................................................................................................................4 2) General Information.............................................................................................................................4 2.1) Unpacking and Inspection.............................................................................................................4 2.2) System Components......................................................................................................................4 2.3) Specifications ................................................................................................................................5 2.4) Outline Drawing............................................................................................................................7 3) Operation and Installation ....................................................................................................................7 3.1) General ..........................................................................................................................................7 4) Sensor Static Calibration Verification .................................................................................................8 5) Declaration of Conformity ...................................................................................................................9 3 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 1) Introduction Dynalabs Inertial Measurement Units are based on triaxial accelerometers and triaxial gyroscopes that are integrated in a single housing. The inertial measurement unit (IMU) is based on proven microelectromechanical systems (MEMS) accelerometers and gyroscopes for detecting the smallest linear accelerations and angular rates. Dynalabs IMUs enable separate analog voltage outputs for all 6 degrees of freedom (DOF). IMUs enable power supply voltage from 6 to 20 VDC. Dynalabs IMUs feature a lightweight, reliable aluminum housing with protection class IP68 and have cable with configurable length and connectors. DYN-I-9000 sensors offer the following options; · Custom Cable Length · Custom Housing Material · Custom Connector · Base plate 2) General Information 2.1) Unpacking and Inspection Dynalabs products provide adequate protection for undamaged products to be transported. Document the damages that occur indirectly during the transport and contact the customer representative. 2.2) System Components The DYN-I-9000 has the following components: -MEMS Sensor - Calibration Certificate - Product Manual 4 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 2.3) Specifications Table 1 Gyroscopes Specifications Datasheet Full scale angular velocity Frequency range Non-linearity (full scale) Noise (in band) Scale factor (nominal) Scale factor var. over. temp. Bias variation with temp. (°/s) (Hz) (%) (°/s /Hz) (V/°/s) (%) (°/s) ±75 0-150 0.06 0.0075 0.012 0.5 ± 1 ±150 0-150 0.06 0.0075 0.006 0.5 ± 2 ±300 0-150 0.06 0.0075 0.003 0.5 ± 3 ±900 0-150 0.06 0.0075 0.001 0.5 ± 4 Table 2: Accecelerometers Specifications Datasheet Full scale (g) ±2 ±4 ±8 ±10 ±20 ±40 ±50 ±100 ±200 ±500 acceceleration Frequency (Hz) range (±3dB) 1,500 1,500 1,500 1,500 1,500 1,500 3,000 3,000 3,000 3,000 Non-linearity (%) 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 (full scale) (g/ Noise (in Hz) 20 25 25 75 80 85 70 50 100 260 band) Scale factor (mV/g) 400 200 100 80 40 20 40 20 10 4 (nominal) 5 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Environmental Table 3: Environmental Specifications datasheet Protection Level IP 68 Operating Voltage 6 V 20 V Operating Temperature Operating Current Consumption mA Isolation -40 °C to +100 °C <50 mA Case isolated Physical Table 4: Physical Specifications datasheet Sensing Element Housing Material Connector (Optional) Mounting Base plate (Optional) Weight (without cable) MEMS Capacitive Vibrating ring Aluminum or Steel D-Sub 9 or 15 pin, Lemo, Binder Adhesive or screw mount Aluminum or Steel 27.5 g (aluminum) 69.5 g (steel) 6 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 2.4) Outline Drawing The dimensional properties of DYN-I-9000 sensors are given below; 3) Operation and Installation 3.1) General The general sensor connector configuration is given below; Cable Code/Pin Configuration: · Red : V + Power supply voltage +6 to +20 VDC · Black : Ground Power GND · X -Axis : Yellow : Signal(+) Positive, analog output voltage signal for differential mode. Purple : Signal(-) Negative, analog output voltage signal for differential mode. ·Y -Axis : Blue : Signal(+) Positive, analog output voltage signal for differential mode. Green : Signal(-) Negative, analog output voltage signal for differential mode. ·Z -Axis : White : Signal(+) Positive, analog output voltage signal for differential mode. Orange : Signal(-) Negative, analog output voltage signal for differential mode. 7 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. Cable Code/Pin Configuration: · Red · Black : V + : Ground Power supply voltage +6 V to +20 VDC. Power GND · RX : Brown : Gyro Signal X-Axis: Analog output voltage signal for single-ended mode. · RY : Grey : Gyro Signal Y-Axis: Analog output voltage signal for single-ended mode. · RZ : Pink : Gyro Signal Z-Axis: Analog output voltage signal for single-ended mode. · White- Brown : nc Not connected. WARNING Never connect the power supply and/or the power ground to yellow, purple, blue, green, white, orange, brown, grey, and/or pink cables. Never connect the power supply to the power ground. Always use a clean power source and check the voltage range. 4) Sensor Static Calibration Verification Using gravity for the accelerometer of the 9000 series IMU, voltage values are measured in the + and - gravity directions, providing a value of ±1 g. The measurement should be made as follows; When the acceleration value of 9000 series IMU's accelerometers is entered into the data acquisition system, the sensor shows +1 g with the effect of gravity, which is in the direction of the axis to be calibrated. When the sensor is positioned in the opposite direction to the axis to be calibrated, the arrow shows -1g as shown below under the effect of gravity. Using gravity, the voltage values that provide 1 g in the + and - directions are measured and compared with the catalog value. The calibration value should be close to the catalog value with 10% tolerance. Sensor catalog sensitivity values are given in Table 2. 8 All rights reserved. Reproduction or issue to third parties in any form whatsoever is not permitted without written authority from the proprietors. 5) Declaration of Conformity This declaration of conformity is issued under the sole responsibility of the manufacturer. The product(s) are developed, produced and tested according to following EC- directives: · 2014/35/EU Low Voltage Directive (LVD) · 2006/42/EU Machinery Safety Directive · 2015/863/EU RoHS Directive Applied standards: · EN 61010-1:2010 · EN ISO 12100:2010 · MIL-STD-810-H-2019 (Test Methods: 501.7 - High Temperature, 502.7 - Low Temperature, 514.8 - Vibration, 516.8 Shock) DYNALABS MÜHENDSLK SANAY TCARET LMTED RKET declares that above mentioned products meet all the requirements of the above mentioned standards and regulations. Murat Aykan, Technical Manager Ankara, 15.07.2021 9