4D-F10 Drone User Manual

Important Safety Information and Warnings

Keep packaging and manual for future reference.

Responsibility: You are responsible for safety and any damages caused by the drone.

Safe Distance: Maintain 2-3m distance from the drone during operation to prevent danger.

Manufacturer Liability: The company and distributors are not liable for losses, damages, or injuries due to improper use or operation.

Child Supervision: Children under 14 must be supervised by adults. This product is not for children under 14 years of age.

Assembly: Follow instructions. Some parts should only be assembled by adults.

Small Parts: Keep away from children to prevent accidental ingestion or suffocation.

Prohibited Areas: Do not operate on roads or near water bodies to avoid accidents.

Disposal: Dispose of drone packaging responsibly.

Modification: Do not disassemble or modify the drone; it may cause malfunction.

Charging Cable: Use only the specified 5V 2A power source, matching the product label.

Other Cables: Using non-specified charging cables can damage the battery and cause unexpected hazards.

Charging Safety: Never leave charging batteries unattended. Keep away from flammable materials.

Battery Handling: Do not squeeze batteries to avoid explosion. Do not mix different types of lithium batteries. The drone uses a lithium battery that must be removed for charging. Do not disassemble, throw batteries into fire, or place them in high-temperature environments (e.g., near fire or heating devices). Do not expose batteries to impact, open them, or expose them to water. Supervise batteries during charging.

Interference: Operate the drone as far as possible from other electrical and magnetic devices, which may cause interference.

Propellers: Maintain a safe distance from rapidly spinning propellers to avoid burns or cuts.

Motors: Motors are hot parts; do not touch them to avoid burns.

LEDs: LEDs emit laser radiation; do not point them directly at people.

Noise: Do not use the model near ears! Improper use may cause hearing damage.

USB Cable: The USB charging cable must be connected to the data cable provided by the company for battery charging. Otherwise, it will cause serious battery damage and lead to unexpected danger.

Battery Charging Procedure: Turn off the equipment and disconnect the battery when discharged. After 30 minutes of rest, begin charging; otherwise, the battery may be damaged.

Flight Restrictions: UAV models cannot fly within 10 km on either side of the centerline and 20 km at both ends of an airport runway, or near civil aviation routes and airlines. It is forbidden to use drones in no-fly zones designated by state authorities.

Included Accessories

• Drone x1
• USB Cable x1
• Propeller Pairs x2
• Lithium Battery x1
• Screwdriver x1
• User Manual x1

Drone Components

Diagram showing the drone with labels pointing to:

• Propeller Mounts
• Motor
• LED Lights
• Camera
• Rear Camera
• Battery
• Cover
• Propellers

Propeller Installation

3.1 Remove Propeller: Unscrew and remove the propeller.

Note: Propellers are marked ABCD. Install A with C, and B with D. Incorrect installation will prevent flight.

3.2 Replace Propeller: To replace propellers, loosen the screw, remove the propeller and connecting parts. If propeller B/D is damaged, replace it with B/D. Similarly, if A/C is damaged, replace it with A/C. Incorrect replacement will prevent flight.

Drone Startup (Pre-flight Preparation)

4.1 Unfold Drone: Follow the diagrams to unfold the drone arms.

5.1 Battery Installation: Insert the lithium battery into the drone's compartment.

5.2 Battery Removal: Remove the lithium battery from the drone.

5.3 Charging: Connect the USB cable to a computer USB port (or a 5V 2A adapter). Connect the other end to the battery. The LED indicator is red while charging and turns green when fully charged.

Warning: Always use the provided charging cable. Other cables may cause complications.

Controller Components

Diagram of the drone controller with labels for:

• Acceleration
• 360° Rotation
• Left Stick
• Switch
• Trim Button
• Right Stick
• LED Indicator
• Rotation Button
• Quick Start/Landing
• Emergency Button (single press/quick calibration, long press for return)
• Headless Mode (single press/quick return, long press for return)

Controller Battery Installation

7.1 Install Batteries: Unscrew the battery cover with the screwdriver and remove it.

7.2 Insert Batteries: Insert 4 x "AAA" batteries (not included) according to polarity markings on the battery compartment.

Note: 1. When inserting batteries, identify the positive and negative poles. 2. Do not mix old and new batteries. 3. Do not mix different types of batteries.

Charging Instructions: Do not place charged batteries in high temperatures, near open flames, or heating devices, as this may cause damage or explosion. Do not subject batteries to impact, open them, or expose them to water. Supervise batteries during charging.

Flight Environment

Suitable: Fly in open spaces without rain, snow, or strong winds (up to force 3). Avoid: People, trees, power lines, tall buildings, airports, signal towers during flight. Do not fly indoors or in areas with weak GPS signals.

Pre-flight Preparation

9.1 Drone Power On: Turn on the drone and place it horizontally. The drone will automatically enter pairing mode; the front white and rear red lights will flash. Note: Ensure the drone is oriented correctly, pointing forward, on a level surface.

9.2 Controller Power On: Press the power button (Step 1). The indicator will flash. Move the left stick up (Step 2) then down (Step 3) to sync frequency. Lights will change from flashing to solid.

9.3 Calibration: Briefly press the horizontal calibration button on the controller. White and red lights will flash rapidly. When lights become solid, calibration is complete (Figure 1).

App Operation: In the app, click "More Settings" and follow the displayed steps (Figure 2).

Note: Calibration requires the drone to be on a horizontal surface.

Start/Stop & Quick Takeoff/Landing

11.1 Start/Stop: Push the left joystick up on the controller (Figure 2). The drone will take off. All indicators will be on. To land, press the quick landing button (Figure 3).

11.2 Quick Takeoff and Landing: After unlocking, gently press the "One Key Takeoff/Landing" button (Figure 4). The drone will ascend to about 1 meter for stable flight. Pressing again will initiate a slow landing.

Controller Operation

Left Stick:

• Up: Ascend ⬆️
• Down: Descend ⬇️
• Left: Rotate Left ⬅️
• Right: Rotate Right ➡️

Right Stick:

• Up: Move Forward ⬆️
• Down: Move Backward ⬇️
• Right: Move Right ➡️
• Left: Move Left ⬅️

360° Rotation

The drone can perform 360° flips. Perform maneuvers at a height of at least 1.5m. It's best done during ascent for easier height control.

• 11.1 360° Left: Press the 360° rotation button, then push the right joystick left.
• 11.2 360° Right: Press the 360° rotation button, then push the right joystick right.
• 11.3 360° Forward: Press the 360° rotation button, then push the right joystick forward.
• 11.4 360° Backward: Press the 360° rotation button, then push the right joystick down.

Other Controller Functions

12.1 Headless Mode: The drone's front is the default forward direction in headless mode. To adjust, re-enable code-matching and briefly press the headless button (Figure 5).

12.2 Quick Return: If the drone flies too far, use the quick return function. The controller must face the drone. Press and hold the quick return button (Figure 6). A sound indicates activation, and the drone will return to the operator. Any joystick movement cancels the function.

12.3 Speed Change: Default speed is slow (Level 1). Press the speed button to change. One beep: Level 1 (slow). Two beeps: Level 2 (medium). Three beeps: Level 3 (fast) (Figure 7).

Tuning Function

12.4 Tuning:

• Forward/Backward Tuning: If the drone drifts backward, press and hold button 1 for forward trim. If it drifts forward, press and hold button 2 for backward trim.
• Left/Right Tuning: If the drone drifts right, press and hold button 3 for left trim. If it drifts left, press and hold button 4 for right trim.

Mobile App Installation

13.1 Download & Install: Program can be downloaded by scanning the QR codes.

13.2 Installation:

1. Turn on the drone and go to Menu Settings on your smartphone or iPad, then open Wi-Fi connection. Search for the device named "4DRC**********" and connect.
2. Open the app (4D FLY icon) and enter the operation mode. During flight, try to avoid other signal sources.

App Workflow: Wi-Fi Connection > Open 4D FLY App > Click Operation Icon > Operation Menu.

Pre-flight Preparation (via App)

14.1 Frequency Tuning: Turn on the drone and place it stably on a horizontal position. In this situation, the drone automatically enters frequency tuning mode - the front and rear white LED lights flash. Note: Ensure the drone is oriented correctly. Its nose should point in the direction of flight.

14.2 Wi-Fi Connection: Turn on the mobile device's Wi-Fi, select the device named "4DRC**********" from the list (Figure 8). After a successful connection, open the app and click OFF (Figure 9), then the hourglass button. The LED lights will illuminate normally, indicating correct frequency tuning (Figure 10).

14.3 Horizontal Calibration: App operation: Click the icon in the mobile app menu (Figure 11). The LED lights on the drone surface will illuminate, indicating that calibration is complete.

Note: Horizontal calibration can only be performed when the drone is in a horizontal position.

Quick Start and Landing (via App)

14.4 Operation via App: Click the quick start and landing button (Figure 12) in the app to activate the quick start option. During flight, click the button again to activate the quick landing option - the drone will automatically proceed to landing.

Operation via App

Left Stick:

• To take off and ascend, push the left joystick up in the app. ⬆️
• To land the drone, push the left joystick down in the app. ⬇️
• To turn left, push the left joystick left in the app. ⬅️
• To turn right, push the left joystick right in the app. ➡️

Right Stick:

• To fly forward, push the right joystick up in the app. ⬆️
• To fly backward, push the right joystick down in the app. ⬇️
• To tilt the drone left, push the right joystick left in the app. ⬅️
• To tilt the drone right, push the right joystick right in the app. ➡️

Other App Functions

16.1 Headless Mode: App operation: The drone's front is the default forward direction in headless mode. If direction adjustment is necessary, re-enable pairing and enter the app menu, then click the headless mode button (Figure 13).

Tip: Ensure the drone is aligned straight for the gyroscope to automatically detect the line, enabling automatic straight-line flight.

16.2 Speed Adjustment: Click the "30%" icon in the mobile app (Figure 14) to select flight speed.

16.3 Orbit Mode: Click the flight path tracking button in the mobile app to open the drawing screen. Drag your finger across the screen to set the flight path the drone will follow (Figure 15).

16.4 Gesture Control: Click the gesture control button.

Tip: For optimal gesture control, stand about 2-3 meters from the drone camera in good lighting conditions.

• OK Gesture (Right Hand): From about 3m from the drone camera lens, perform an OK gesture with your right hand horizontally. After the drone successfully recognizes the gesture, it will count down 3 seconds and take photos. ✋
• V Gesture: From about 3m from the drone camera lens, perform a V gesture. The drone will start recording. Recording will end upon recognizing the gesture again (the time difference between two recognitions should be greater than 3s). ✌️

FAQ