SJCAM C200PRO 4K Anti-Shake Camera

User Manual

Please read this manual carefully before use and keep it in a safe place.

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure without restriction.

Safety Guidelines

1. Do not place this product near objects with strong magnetic fields, such as magnets or motors. Also avoid placing this product near objects that emit strong radio waves to prevent malfunctions.
2. Please choose a reputable brand of Micro SD card.
3. Do not place the Micro SD card near objects with strong magnetic fields to avoid data loss.
4. If the product overheats, smokes, or smells strange during charging, pull out the charging device and stop charging immediately to avoid fire.
5. When charging, place the product where children cannot reach it to avoid electric shock and other accidents.
6. Place the product in a cool, dry, and dust-free location. Do not expose it to high temperatures or direct sunlight.
7. This product is a high-precision instrument; do not drop or subject it to collision.
8. Please choose an official recycling point to recycle this product or battery; do not dispose of it in the garbage. ♻️

If you have any questions, please contact customer service. Please do not disassemble without authorization!

Product Description

The camera is shown from the front and back. The front view displays the screen, a button below it, and a speaker grille. The back view shows the screen, indicator lights, and a lens. Side views reveal buttons and ports.

Key Components:

1. Up/M button

2. Down / WiFi button

3. Screen

4. Speaker

5. On/Off/OK button

6. Reset button

7. TF cardholder

8. TYPE-C

9. Microphone

10. Lens

Packing List

• Camera ×1
• Waterproof Case ×1
• Base Mount ×1
• Frame Mount ×1
• Back Clip ×1
• 3M Sticker ×2
• Helmet Base ×2
• USB Cable ×1
• Wiping Cloth ×1
• User Manual ×1

Specifications

Remote Control Instructions

A diagram shows a small remote control with four buttons labeled 1, 2, 3, 4.

Buttons:

1. 1. Power button: Turn off the camera
2. 2. Photo button: Take photos
3. 3. WiFi button: Turn on/off camera WiFi
4. 4. Video button: Start/stop recording

Note: Remote control is not a standard accessory; it needs to be purchased separately.

After powering on the camera, slide down from the top to access the preview screen. Click the remote control icon to select the remote control matching. The camera enters the matching interface. Press the remote control video button and the photo button simultaneously. Upon successful matching, the camera will indicate pairing completion. You can then operate the camera through the remote control.

Figure 1 shows the camera's preview screen with recording information. Figure 2 illustrates the remote control buttons being pressed. Figure 3 displays a pairing ID.

App Download & WiFi Connection

Scan the QR code on your smartphone or search for "SJCAM ZONE" in the App Store or Google Play to download and install the App.

WiFi Connection Steps:

1. Slide the screen from top to bottom, click the WiFi icon to turn on the camera WiFi. The QR code will be displayed on the camera screen.
2. Open the downloaded APP on your phone, click "Connect Camera → Scan Code to Connect". After scanning the QR code on the camera, your phone will enter the APP preview interface (interface may vary slightly between different smartphone systems).
3. After successful connection, you can take photos, videos, change settings, and perform other operations in the App.

Operation Guide

1. Micro SD Card Installation

Press and hold the button, then slide the cover down to open the Micro SD card port. Insert the card into the slot, paying attention to the direction, and gently press inward until a clicking sound is heard.

2. Recording

Power on the camera to enter recording mode. Short press the OK button to start recording and short press again to stop. The recording icon turns red, and the video duration is displayed. The blue light next to the OK button blinks during recording.

Note: After setting the camera mode, it has a memory function; the camera will remember the mode before it was turned off when powered on again.

3. Photo

After turning on the camera, click the [Home Icon] at the bottom of the screen or slide the screen to enter the mode interface. Slide left/right to select the [Photo Icon] to enter photo mode, then press the OK button to take photos.

4. Playback

When the camera is on, slide down the screen and click the [Playback Icon] to enter playback mode. Select the video/photo you want to playback, then press OK to browse.

5. Car Mode

After turning on the camera, click the [Home Icon] at the bottom of the screen or slide the screen up to enter the mode interface. Slide left/right to select the [Car Mode Icon] and click it to enter Car Mode.

Note: 1. If installing the camera upside down in car mode, enable rotation in system settings. 2. After connecting the car power adapter, the camera will automatically turn on and record when the car starts, and will automatically stop recording and turn off after the power is disconnected for about 5 seconds.

6. Charging

A power adapter or car charger can charge the camera. The device's red light is on while charging and turns off when fully charged.

Note: Please use a 5V1A or 5V2A output power adapter.

7. Recording Settings

A. In the video preview interface, click the [Settings Icon] at the bottom of the screen. Slide the screen to select the desired option and click to confirm.

B. Recording Setup Menu

• Resolution: 4K (3840*2160) 30fps, 2K (2560*1440) 60/30fps, 1080P (1920*1080) 120/60/30fps, 720P (1280*720) 120/60/30fps
• Video encoding: H.264, H.265
• Loop recording: Off, 3 minutes, 5 minutes, 8 minutes
• Capture interval: Off, 5 seconds, 10 seconds, 30 seconds, 1 minute
• Vertical Screen Mode: Off, On
• Motion Detection: Off, On
• Pre recording: Off, On
• Delay recording: Off, On
• Viewing Angle: Wide, Medium, Narrow
• WDR: Off, On
• HDR: Off, On
• Gyro stabilization: Off, On
• Sound recording: Off, On
• Volume adjustment: 1, 2, 3, 4, 5, 6, 7, 8
• Date labeling: Off, On
• LOGO watermark: Off, On
• Code Stream: High, Medium, Low
• ISO: Auto, 100, 200, 400, 800, 1600, 3200
• Sharpness: strong, standard, soft
• Saturation: High, Standard, Low
• Contrast: High, Standard, Low
• Noise Reduction: High, Standard, Low
• Image Brightness: High, Standard, Low
• White Balance: Auto, Cloudy, Daylight, Tungsten, Fluorescent, Underwater mode
• Color: Normal, Black & White, Retro, Warm Tone, Cool Tone
• Exposure compensation: +2.0, +5/3, +4/3, +1.0, +2/3, +1/3, 0.0, -1/3, -2/3, -1.0, -4/3, -5/3, -2.0
• Metering: Average, Center, Spot
• Fisheye correction: Off, On

Photo Settings

A. On the photo preview interface, click the [Settings Icon] at the bottom of the screen. Slide the screen to select the option to be set, and click to confirm the selection.

B. Photo Setup Menu

• Photo resolution: 20M(5888*3312), 16M(5376*3024), 14M(5008*2816), 12M(4640*2608), 10M(4320*2432), 8M(3840*2160)
• Burst mode: off, 3P, 5P, 10P, 30P
• Interval shooting: off, 3 seconds, 5 seconds, 10 seconds, 20 seconds, 5 minutes, 15 minutes, 30 minutes
• Time-lapse photo: off, 3 seconds, 5 seconds, 10 seconds
• Exposure time: Auto, 1/30 sec, 1 sec, 2 sec, 5 sec, 10 sec, 20 sec, 30 sec
• Image Quality: Premium, Standard, Economical
• Sharpness: Strong, Normal, Soft
• Saturation: High, Normal, Low
• Contrast: High, Normal, Low
• Noise Cancellation: High, Normal, Low
• Image Brightness: High, Normal, Low
• White Balance: Auto, Cloudy, Daylight, Tungsten, Fluorescent, Underwater
• Color: Normal, Black & White, Retro, Warm, Cool
• ISO: Auto, 100, 200, 400, 800, 1600, 3200
• Exposure compensation: +2.0, +5/3, +4/3, +1.0, +2/3, +1/3, 0.0, -1/3, -2/3, -1.0, -4/3, -5/3, -2.0
• Metering mode: average metering, central metering, spot metering
• WDR: Off, On
• HDR: Off, On
• Fisheye Correction: Off, On
• Date tags: off, date, datetime

System Settings

A. On the camera preview interface, click the [Settings Icon] in the lower right corner of the screen to enter the setting interface. Select the menu to be set by sliding the screen up and down, and click to confirm the selection.

B. System Setup Menu

• Language setting: English, French, German, Spanish, Italian, Portuguese, Chinese, Japanese, Traditional Chinese, Russian, Romanian, Polish, Czech, Slovak, Hungarian, Finnish, Danish, Dutch, Turkish, Hebrew
• Time/Date: H/M/S: YY/MM/DD
• Formatting: Yes, no
• Quick Recording: Off, On
• Quick photo: Off, on
• Indicator light: Off, on
• Automatic shutdown: Off, 3 minutes, 5 minutes, 10 minutes
• Button sound: Off, on
• Voice broadcast: Off, on
• LED brightness adjustment: Low → high
• Screen saver: 30 seconds, 1 minute, 3 minutes, 5 minutes, off
• Light source frequency: 50Hz, 60Hz
• Rotation: Off, on
• WiFi band: 2.4G, 5G
• Default setting: Restore factory settings
• Version: Check the version information

Product Information & Support

Product features may change with product upgrades or updates; please refer to the actual product specifications.

If you need after-sales service, please contact SJCAM customer service.

Technical support email: support@sjcam.com

Welcome to visit SJCAM official website: www.sjcam.com

Manufacturer: Shenzhen Zhencheng Technology Co., Ltd.