Computer Desk With Drawer

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Do Not Return This Product!

Contact our customer service team for help first.

Assembly Difficulty Meter: Easy Tough

Contact Us!

Do NOT return this product! Contact our friendly customer service team first for help.

Assembly Tips ▶️ [YouTube]

Helpful Hints

PEOPLE NEEDED FOR ASSEMBLY: 2

ESTIMATED ASSEMBLY TIME: 1 HOUR

• Open your item in the area you plan to keep it to avoid excessive heavy lifting.
• Identify, sort and count the parts before attempting assembly.
• Compression dowels are lightly tapped in with a hammer ?.
• Slides are labeled with a R (right) and L (left) for proper placement.
• Make sure to always face the point on the top of the Cam Lock towards the outer edge.
• Use all the nails provided for the back panel and spread them out equally.
• Back panel must be used to make sure your unit is sturdy.
• Do NOT use harsh chemicals or abrasive cleaners on this item.
• Never push, pull, or drag your furniture.

Diagram descriptions:

• [Image: Hammer tapping a dowel into a panel]
• [Image: Screwdriver]
• [Image: Cam lock and cam cover components]
• [Image: Nails being spread out]
• [Image: Warning symbol indicating not to use chemicals]
• [Image: Symbol indicating not to drag furniture]

Before You Start

Quick Assembly Tip

• Read through each step carefully and follow the proper order.
• Separate and count all your parts and hardware.
• Give yourself enough room for the assembly process.
• Have the following tools: Flat Head Screwdriver ?, #2 Phillips Head Screwdriver ?, and Hammer ?.
• Caution: If using a power drill or power screwdriver for screwing, please be aware to slow down and stop when screw is tight. Failure to do so may result in stripping the screw.

Cam Lock Fastening System

This Cam Lock Fastening System will be used throughout the assembly process.

Diagrams illustrating the Cam Lock system:

1. A screw is inserted into a panel.
2. A cam lock is inserted into a corresponding hole on another panel, with its arrow pointing towards the edge.
3. The two panels are joined, and the cam lock is turned to secure them.
4. A cam lock is shown fully engaged.

Detail: Proper orientation of CAM LOCK (unlock and lock positions shown).

Board Identification

(Not Actual Size)

Associated parts for assembly:

• Left slide track: TKX1027-2
• Left slide runner: TKX1027-1
• Right slide track: TKX1028-2
• Right slide runner: TKX1028-1
• Screw(12)Ø3.5x12mm: TKX1016

Diagram: Exploded view showing how parts A, B, C, and D connect.

Part List

(Note: Part 1 and 5 are shown actual size, Parts 2, 3, 4 are not actual size)

Assembly Steps

STEP 1

Diagram: Attaching cam bolts (2) to leg frames (C and D). Two cam bolts are shown being screwed into each leg frame.

STEP 2

Diagram: Connecting modesty panel (B) to leg frames (C and D) using cam locks (3) and cam covers (4). The proper orientation of the cam lock is indicated.

STEP 3

Diagram: Attaching the assembled leg structure (C, D, B) to the table top with drawer (A) using bolts (1) and the hex key (5).

Note: Tighten all bolts to secure the unit in this assembly step.

STEP 4

Diagram: Further securing the unit by attaching additional bolts (1) using the hex key (5).

Note: Tighten all bolts to secure the unit in this assembly step.

Maximum Loads

This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury.

Diagram: Desk showing load capacities.

Top surface: 80 Lbs / 36.3 Kgs

Drawer: 15 Lbs / 6.8 Kgs

Warning: Risk of injury to persons - do not place a television on this furniture. This furniture is not approved for use with a television.

Certificate of Conformity

1. This certificate applies to the Dorel Home Furnishings, Inc. product identified by this instruction manual.

2. This certificate applies to compliance of this product with the CPSC Ban on Lead-Containing Paint (16 CFR 1303).

3. This product is distributed by: Dorel Home Furnishings, Inc.

410 East First Street South
Wright City, MO 63390
636-745-3351

4. Site of Manufacture: Svay Rieng, Cambodia

5. See front page of instruction manual for date of manufacture.

Register Your Product

Register your product to receive the following:

• New trend details - sneak peek on what's new
• Surveys - have a voice within our community
• Exclusive deals and discount codes
• Quick and easy replacement part service

To register your product, visit ameriwoodhome.com

Star Rating

Visit your local retailer's website, rate your purchased product and leave us some feedback!

We would like to extend a big "Thank You" to all of our customers for taking the time to assemble this Home product, and to give us your valuable feedback.

Thank You!