Instruction Manual for Sunricher models including: sr-mt9040a-s Matter Thread Micro Smart Dimmer, sr-mt9040a-s, Matter Thread Micro Smart Dimmer, Thread Micro Smart Dimmer, Micro Smart Dimmer, Smart Dimmer, Dimmer
Matter Dimmer für Beleuchtung 230V Sunricher SR-MT9040A-S | max 400W
25 мар. 2025 г. — Read All Instructions Prior to Installation. Features. Safety & Warnings. • Matter thread AC phase cut dimmer. • 100-240VAC wide input and ...
Matter stmívač LED osvětlení 230V Sunricher 400W
Matter Thread Micro Smart Dimmer Function Introduction · ImportantRead All Instructions Prior to Installation. Switch input Micro Smart Dimmer C O M S1 "Reset" Key: Press and hold for over 5 seconds to factory reset the dimmer Reset Min.Set OUT AC 100-240V L LN N Load output "Min.Set" Key: Minimum brightness and startup brightness set button AC power input (2-wire with No Neutral input) (3-wire with Neutral input) Product Data Input Voltage 100-240VAC Output Voltage 100-240VAC Output Current 1.8A max Size (LxWxH) 45.5x45x20.3mm Load Symbol Load Type Compatible Load Types Maximum Load Remarks Dimmable LED lamps 200W @ 230V 100W @ 110V Due to variety of LED lamp designs, maximum number of LED lamps is further dependent on power factor result when connected to dimmer. Dimmable LED drivers 200W @ 230V 100W @ 110V Maximum permitted number of drivers is 200W divided by driver nameplate power rating. Incandescent lighting, HV Halogen lamps 400W @ 230V 200W @ 110V Low voltage halogen lighting with electronic transformers 200W @ 230V 100W @ 110V 1 Features · Matter thread AC phase cut dimmer · 100-240VAC wide input and output voltage · Supports resistive loads, capacitive loads or inductive loads · 1 channel output, up to 400W · Input and output with screw terminals, safe and reliable · Trailing edge dimming · Compatible with universal Matter gateways: the latest Apple HomePod mini, Google Home, Amazon Echo devices etc. · Can be controlled through the Apple Home app, Google Home app, Amazon Alexa app · Can be voice controlled through Apple Siri, Google Assistant, Amazon Alexa · Mini Size, easy to be installed into a standard wall box · Waterproof grade: IP20 Main Features: · Can operate under two-wire connection with no neutral lead or three-wire connection with neutral lead · Advanced microprocessor control · Implemented algorithm of smart light source detection · Active power and energy metering functionality · Soft start function · Innovative minimum dimming level and startup brightness setting function · Works with various types of switches momentary, toggle, three-way, etc. · Active element: semiconductor electronic switch · To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of applicable regulations · The Bypass is an extension unit As a dimmer it operates under the following loads: · Conventional incandescent and HV halogen light sources · ELV halogen lamps and dimmable LED bulbs (with electronic transformers) · MLV halogen lamps (with ferromagnetic transformers) · Dimmable LED bulbs · Dimmable compact fluorescent CFL tube lamps · Supported dimmable light sources (power factor > 0.5) with minimal power of 3VA using the Bypass (depending on the type of load) Safety & Warnings · DO NOT install with power applied to the device. · DO NOT expose the device to moisture. Operation 1 Do wiring according to connection diagram correctly.(See P9-10) 2 This Matter thread device is a wireless receiver that communicates with a variety of Matter compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible Matter system. 2 3 Add to a Matter gateway and control through the gateway: 5 6 7 Note An Apple HomePod mini is used as a Matter border router for adding and controlling the device. For other Matter border routers, please refer to their user manuals to learn how to add and control Matter devices. Step 1: Prepare an iPhone (iOS 16.2 or later) or iPad (iPadOS 16.2 or later) with the latest version firmware, and prepare an Apple HomePod mini with the latest version firmware. Step 2: Connect the iPhone or iPad to your home WLAN network. Run the Apple Home app and set up the HomePod mini as instructed by Apple (as shown in Figure 1 to Figure 7). 1 2 3 4 Step 3: Do wiring of the Matter thread dimmer according to the wiring diagram (See P9-10) and power on it. Step 4: Add the Matter thread dimmer to the Apple Home app by scanning the QR code sticker on the dimmer as shown in Figure 8 to Figure 16. 8 9 3 4 NoteBefore scanning the QR coder sticker on the dimmer as shown in Figure 10, short press the reset button 5 times to reset the dimmer so that it can be discovered by the Apple Home app. Otherwise if it has already been added to another gateway, current gateway can not discover and add it. Press 5X Reset 10 11 12 13 14 15 16 Note When choose the room that you would like to add the dimmer to, please make sure to choose the same room that the HomePod mini is located as shown in Figure 14. Step 5: Once the dimmer is added to the gateway successfully, tap on the device to control on/off and brightness of the dimmer as shown in Figure 17 to Figure 19. 17 18 19 5 6 4 Minimum and Startup Brightness Setting Button Minimum brightness: Press and hold for 3S Startup brightness: Press 2X Min.Set Min.Set Press and hold down the button for 3 seconds to set minimum brightness: when current brightness value is 1%-50%, it will be set as minimum brightness. When current brightness value is 100%, previously set minimum brightness will be deleted. Once a minimum brightness is set, the connected load can not be dimmed below this level. Short press the button twice to set startup brightness: when current brightness value is 1%-50%, it will be set as startup brightness. When current brightness value is 0%, previously set startup brightness will be deleted. Note startup brightness setting function is to avoid the phenomenon that some dimmable LED drivers can not be turned on after dimmed to a low level and turned off. Once setting a startup brightness, if the startup brightness is higher than dimmed level before turned off, the driver will first go to the startup brightness after turned on then drop down to the dimmed level. If the startup brightness is lower than the dimmed level before tured off, the driver will directly go to the dimmed level after turned on. 5 Controlled by a push switch Once connected with a push switch, click the push switch to switch ON/OFF, press and hold down it to increase/ decrease light intensity. Wiring Diagram * Notes for the diagrams: L - terminal for live lead N - terminal for neutral lead Out - output terminal of the dimmer (controlling connected light source) S1 - terminal for switch COM - terminal for grounding to the switch connected to the dimmer * Supported Switch Types: The switch types this device supports can be configured by factory setting: 1. Push Switch (factory default setting) 2. Toggle On/Off Switch (can be configured by factory setting upon request) 7 * Compatible load types and recommended values of power for supported loads: Supported load types 100-240V~ Resistive loads Conventional incandescent and halogen light sources 20-400W @ 230V 20-200W @ 110V Capacitive loads Fluorescent tube lamp (compact / with electronic ballast), electronic transformer, LED Using Bypass: 3-200W @ 230V 3-100W @ 110V No Bypass Used: 20-200W @ 230V 20-100W @ 110V Inductive loads Ferromagnetic transformers 20-200W @ 230V 20-100W @ 110V COM S1 COM S1 (1) 2-Wire Connection With No Neutral Lead With PUSH LV PUSH Micro Sm art Dim m er Reset Min.Set OUT AC 100-240V L LN N With PUSH PUSH Micro Sm art Dim m er Reset Min.Set OUT AC 100-240V L LN N Bypass Bypass Live Neutral Live Neutral Notes Switch connected to the S1 terminal activates the basic functionality of the dimmer (turning the light on/off, dimming). The Bypass is a device designed to work with the micro smart dimmer. It should be used in case of connecting LED bulbs or energy saving compact fluorescent lamps. The Bypass prevents flickering of the LED lights and glowing of the turned off compact fluorescent lamps. In the case of 2-wire connection, the Bypass allows to reduce minimum power of load required by the dimmer for correct operation. The Bypass provides powering of the dimmer in case of controlling the low loads of minimum power down to 3W (for cos>0.5). 8 C O M S 1 C OM S 1 (2) 3-Wire Connection With Neutral Lead With PUSH LV PUSH Micro Sm art Dim m er Reset Min.Set OUT AC 100-240V L LN N With PUSH PUSH Micro Sm art Dim m er Reset Min.Set OUT AC 100-240V L LN N Live Neutral Live Neutral Notes Switch connected to the S1 terminal activates the basic functionality of the dimmer (turning the light on/off, dimming). With PUSH CO M S1 Micro Sm art Dim m er Reset Min.Set OUT AC 100-240V L LN N Live Neutral This phase dimmer adopts leading edge dimming (forward phase control) or trailing edge dimming (reverse phase control), two versions are available for choosing, factory default version is trailing edge. Please make sure the connected loads support the control type you choose. Please refer to the user manual of the load or consult the supplier of the load. Product Dimension (3) Multiple Momentary or Push Switches Connection With PUSH LV CO M S1 Micro Sm art Dim m er Reset Min.Set OUT AC 100-240V L LN N 9 Package 1 PCS/Box 55x55x35mm 10 200 PCS/Carton 380x270x280mmGPL Ghostscript 10.03.0 Adobe InDesign 18.0 (Windows)