Edelkrone SliderPLUS PRO v5 User's Manual

Table of Contents

1. What's in the Box & The Basics
2. Attaching the Belts & Tension Adjustment
3. Attaching the Belts & Tension Adjustment
4. Legs & Angle Adjustment
5. Mounting SliderPLUS on Tripod
6. Mounting Your Camera on SliderPLUS
7. Mounting Your Magic Arm on SliderPLUS
8. Inclined Motion
9. Cleaning Kit
10. Cautions and Tips

1. What's in the Box & The Basics

Components:

• 1. Rubber feet
• 2. Built-in foldable legs
• 3. Magnetic belt clip slot
• 4. 3/8"-16 pop-up screw
• 5. 1/4" mounting port
• 6. Instant locking mechanism
• 7. Incline
• 8. Mounting wheel for 3/8”-16 mounting port
• 9. Cleaning kit (x3)
• 10. 2.5mm-3mm allen keys
• 11. Motion control belt (x2)
• 12. Manual control belt (x2)

A detailed video explaining how to attach the belts can be found at: http://edel.kr/sld5

2. Attaching the Belts & Tension Adjustment

Attach either the manual control belt or the motion control belt depending on use.

1. Remove the wheel.
2. Pass the belt through the hole.
3. Attach the wheel back.

A detailed video explaining how to attach the belts can be found at: http://edel.kr/sld5

3. Attaching the Belts & Tension Adjustment

1. Attach the other head of the belt.
2. If belt tension is low, you may increase it by loosening the side wall screws and pulling out the side walls until desired tension is achieved.

A detailed video explaining how to attach the belts can be found at: http://edel.kr/sld5

4. Leg & Angle Adjustment

To adjust the legs:

1. Loosen the wheel by turning it counterclockwise.
2. Legs are adjustable at each 15°. Adjust the leg at an appropriate angle.
3. Tighten the wheel by turning it clockwise.

A detailed video explaining how to leg adjustment can be found at: http://edel.kr/sld5

5. Mounting SliderPLUS on Tripod

1. Detach tripod head from your tripod.
2. Place your SliderPLUS onto your tripod's 3/8"-16 mounting screw.
3. Mount using the mounting wheel.

A detailed video explaining the process can be found at: http://edel.kr/sld5

6. Mounting Your Camera on SliderPLUS

The SliderPLUS has a 3/8”-16 screw for your tripod head hidden inside. You can access this screw with the help of a coin. Using a coin, turn the screw until it pops out. To hide the screw back again, just press it down and turn it counterclockwise.

1. Place your tripod head on the screw and tighten clockwise.
2. Attach your camera to your tripod head.

A detailed video explaining the mounting process can be found at: http://edel.kr/sld5

7. Mounting Your Magic Arm on SliderPLUS

You can mount any camera head or arm to your SliderPLUS with the 1/4” mounting screw.

A detailed video explaining the mounting process can be found at: http://edel.kr/sld5

8. Inclined Motion

To get inclined shots:

1. Place your SliderPLUS onto the 3/8”-16 mounting screw of your tripod head.
2. Attach your FlexTILT Head or any camera head onto your SliderPLUS.
3. You should attach your Slide Module to the incline side of the SliderPLUS.
4. You should tighten the slide tension of the Slide Module to get inclined motion.
5. Place your camera on the FlexTILT Head or any camera head.

If you are not able to slide manually after inclined operation, try loosening the tension. Make as small adjustments as possible.

Please make sure that your tripod legs are opened widely enough to prevent falls and balance issues. Always make sure that your system is leveled and balanced.

A detailed video explaining inclined motion can be found at: http://edel.kr/sld5

9. Cleaning Kit

1. Separate the slider upper and lower carriages while your slider is resting on a flat surface as shown.
2. Remove a double-sided sticker from the cleaning kit.
3. Stick one side of the sticker on the slider rail as shown and peel off the white cover from the sticker.
4. Slide the slider cars from one end to the other to clean the wheels.
5. Repeat this process for all wheels.

A detailed video explaining how to use the cleaning kit can be found at: http://edel.kr/sld5

10. Cautions and Tips

Please contact our dedicated customer care team for recommended tripod legs.

1. In order to get perfect results with your SliderPLUS, please attach your SliderPLUS directly to tripod legs, not to the tripod head.
2. If your tripod has a feature that allows you to extend the height from its neck, we suggest keeping it down and as tight as possible in order to prevent a rainbow effect.
3. Please make sure that your SliderPLUS withstands within the area of the tripod legs to prevent falls and balance issues. Always make sure that your system is leveled and balanced.
4. Always keep your slider locked while it is not in use.
5. Use built-in foldable legs to level your system.

SliderPLUS can travel twice its own length when it's mounted on a tripod. When using it on its feet, it can only travel its own length.

For more tips, please watch the user's manual videos at: http://edel.kr/sld5

Disclaimer

edelkrone cannot be held responsible for damage caused by improper use or modification of the product.

For more information and tips about your SliderPLUS, please watch the user's manual videos at: http://edel.kr/sld5